Abstract:The 2195 Al-Cu-Li alloy is widely utilized for the fabrication of key aerospace vehicle components; hence, an in-depth understanding of its hot deformation behavior is essential for consistently achieving high-performance products. In this study, isothermal compression tests were performed on 2195 Al-Cu-Li alloy ingots in the temperature and strain rate ranges of 250–500 °C and 10 −3 -1 s −1 , respectively. A processing map was established to predict the workability under different conditions. The corresponding microstructures were examined to reveal their hot deformation mechanism. Results demonstrated that the processing map was divided into four distinct domains. The unstable zone was located in the 250–375 °C/10 −1.5 -1 s −1 and 250–275 °C/10 −2.5 –10 −1.5 s −1 , temperature/strain rate regimes, in which deformation bands and flow localization were observed. The deformation bands blocked dislocations and compromised the dynamic recrystallization (DRX) behavior, hence damaging the microstructure. Further, large coarse T 1 phases precipitated in the 325–410 °C/10 −2.5 –10 −3 s −1 regime, which led to the formation of heterogeneities in the microstructure, corresponding to a minimum workability in the processing map. The optimal hot-working domain for the 2195 alloy was determined to be 460–500 °C/10 −3 –10 −2 s −1 , and the dominating hot deformation mechanisms were DRX and dynamic recovery (DRV). Specifically, continuous and discontinuous DRX behaviors dominated in the 300–400 °C/10 −3 s −1 and 450–500 °C/10 −3 s −1 regimes, respectively. DRX gradually weakened as the strain rate increased at 500 °C. Further, the weakening of DRX was only minimally affected by temperature at 400–500 °C during high-speed deformation (1 s −1 ). The results reported herein can provide valuable insights into the hot working of Al-Cu–Li alloys.

Hot Deformation Behavior of Two Kinds of TC4-xFe Alloys Based on Processing Map

Constitutive equation and hot processing maps of Al–5Ti–1B master alloy

Hot Deformation Behavior of the 20 Vol.% TiC/Cu-Al2O3 Composites

Thermal Deformation Behavior and Microstructural Evolution Mechanism of TC4 Titanium Alloy Based on Hot Processing Map

Deformation Behavior and Constitutive Model for Isothermal Compression of TC4 Alloy

Processing map of titanium alloy TC4 and its application for plate rolling analyses

Hot Deformation Behaviors of the Mg-3Sn-2Al-1Zn Alloy: Investigation on its Constitutive Equation, Processing Map, and Microstructure

Behavior of Hot Deformation and its Effect Factors for TC4 Titanium Alloy

Hot Deformation Characteristics and Processing Parameter Optimization of Al–6.32Zn–2.10Mg Alloy Using Constitutive Equation and Processing Map

High-temperature hot deformation behavior and processing map of Ti-22Al-25Nb alloy

Characterization of Hot Deformation Behavior and Processing Maps of Homogenized Al-Mg-Si-Sc-Zr Alloys

Hot deformation behavior, dynamic recrystallization mechanism and processing maps of Ti–V microalloyed high strength steel

Hot deformation behavior and microstructure evolution of TC11 dual-phase titanium alloy

Hot deformation behavior and process parameters optimization of Ti–6Al–7Nb alloy using constitutive modeling and 3D processing map

Hot Workability and Microstructure Evolution of Homogenized 2050 Al-Cu-Li Alloy during Hot Deformation

Hot deformation behavior and microstructural evolution of the Al-Cu-Li alloy: A study with processing map

Flow Behaviors and Dynamic Recrystallization Mechanisms Study of TC4 under Different Temperatures and Strain Rates

Hot Deformation Behavior of Homogenized Al-7.8Zn-1.65Mg-2.0Cu (wt.%) Alloy

Exploring hot deformation behavior of equimolar CoCrFeNi high-entropy alloy through constitutive equations and microstructure characterization

Hot Deformation Behaviours and Spheroidization Mechanisms of Ti-5322 Alloy During Hot Compression

Constitutive equation and hot processing map of TA15 titanium alloy