Degradation of Tetrabromobisphenol A in Heat Activated Persulfate Oxidation Process

Hao Jin,Deyang Kong,Yuefei Ji,Junhe Lu,Quansuo Zhou

DOI: https://doi.org/10.1039/c6ra02482c

IF: 4.036

2016-01-01

RSC Advances

Abstract:Sulfate radicals (SO4˙−) generated by heat activated persulfate were employed to degrade brominated flame retardant tetrabromobisphenol A (TBBPA).

What problem does this paper attempt to address?

Degradation of Tetrabromobisphenol S by thermo-activated Persulphate Oxidation: reaction Kinetics, transformation Mechanisms, and brominated By-products

Lu Wang,Yaqun Yu,Guoqiang Liu,Baowei Hu,Junhe Lu

DOI: https://doi.org/10.1080/09593330.2022.2135027

IF: 3.475

2022-10-25

Environmental Technology

Abstract:Brominated flame retardants (BFRs) are a group of contaminants of emerging environmental concern. In this study, systematic exploration was carried out to investigate the degradation of tetrabromobisphenol S (TBBPS), a typical emerging BFRs, by thermally activated persulfate (PDS) oxidation. The removal of 5.0 μM TBBPS was 100% after 60 min oxidation treatment under 60°C. Increasing the temperature or initial PDS concentration facilitated the degradation efficiency of TBBPS. The quenching test indicated that TBBPS degradation occurred via the attack of both sulphate radicals and hydroxyl radicals. Natural organic matter (NOM) decreased the removal rate, however, complete disappearance of TBBPS could still be obtained. Six intermediate products were formed during reactions between TBBPS and radicals. Transformation pathways including debromination, β-Scission, and cross-coupling were proposed. Brominated disinfection by-products (DBPs) in situ formed during the degradation of TBBPS were also investigated, such as bromoform and dibromoacetic acid. The presence of NOM reduced the formation rates of brominated DBPs. Results reveal that although thermo-activated PDS is a promising method for TBBPS-contaminated water, it can lead to potential brominated DBPs risks, which should be paid more attention to when SO 4 •− -based oxidation technology is applied. GRAPHICAL

environmental sciences
Cobalt catalyzed peroxymonosulfate oxidation of tetrabromobisphenol A: Kinetics, reaction pathways, and formation of brominated by-products

Yuefei Ji,Deyang Kong,Junhe Lu,Hao Jin,Fuxing Kang,Xiaoming Yin,Quansuo Zhou

DOI: https://doi.org/10.1016/j.jhazmat.2016.04.033

2016-08-05

Abstract:Degradation of tetrabromobisphenol A (TBBPA), a flame retardant widely spread in the environment, in Co(II) catalyzed peroxymonosulfate (PMS) oxidation process was systematically explored. The second-order-rate constant for reaction of sulfate radical (SO4(-)) with TBBPA was determined to be 5.27×10(10)M(-1)s(-1). Apparently, degradation of TBBPA showed first-order kinetics to the concentrations of both Co(II) and PMS. The presence of humic acid (HA) and bicarbonate inhibited TBBPA degradation, most likely due to their competition for SO4(-). Degradation of TBBPA was initiated by an electron abstraction from one of the phenolic rings. Detailed transformation pathways were proposed, including β-scission of isopropyl bridge, phenolic ring oxidation, debromination and coupling reactions. Further oxidative degradation of intermediates in Co(II)/PMS process yielded brominated disinfection by-products (Br-DBPs) such as bromoform and brominated acetic acids. Evolution profile of Br-DBPs showed an initially increasing and then decreasing pattern with maximum concentrations occurring around 6-10h. The presence of HA enhanced the formation of Br-DBPs significantly. These findings reveal potentially important, but previously unrecognized, formation of Br-DBPs during sulfate radical-based oxidation of bromide-containing organic compounds that may pose toxicological risks to human health.
Elimination of Bisphenol A with Visible Light-Enhanced Peroxydisulfate Activation Process Mediated by Fe3+-nitrilotriacetic Acid Complex.

Yan Xiao,Liangliang Xiong,Yin Xu,Hui Zhang

DOI: https://doi.org/10.1016/j.jhazmat.2022.129780

IF: 13.6

2022-01-01

Journal of Hazardous Materials

Abstract:In recent years, visible light assisted advanced oxidation processes (AOPs) are appealing in the elimination of pollutants. Herein, an innovative and eco-friendly visible light enhanced Fe3+-nitrilotriacetic acid system for the activation of peroxydisulfate (Vis/Fe3+-NTA/PDS) was proposed for the removal of bisphenol A (BPA). Fe3+-NTA could be dissociated through ligand-to-metal charge transfer (LMCT) to realize the generation of Fe2+ for the continuous activation of PDS to remove BPA. The use of 0.10 mM Fe3+, 0.10 mM NTA and 1.00 mM PDS led to 97.5% decay of 0.05 mM BPA and 66.3% of TOC removal in 30 min with the illumination of visible light at initial pH 3.0. The sulfate and hydroxyl radicals were proved to be the dominant species leading to BPA removal by means of radical scavenging experiments, radical probes and electron paramagnetic resonance (EPR) technique. The effects of various operating parameters, natural water constituents as well as different water matrices on BPA abatement were explored. The intermediate products of BPA degradation were identified and a possible transformation pathway was proposed. Briefly, this research provides an attractive strategy for the remediation of refractory wastewater using NTA assisted with visible light in the homogeneous Fe3+/PDS system.
Alkali-thermal activated persulfate treatment of tetrabromobisphenol A in soil: Parameter optimization, mechanism, degradation pathway and toxicity evaluation

Yushuang Chen,Rui Shi,Yafei Hu,Wenlai Xu,Neng-Min Zhu,Haijiao Xie,Neng-min Zhu

DOI: https://doi.org/10.1016/j.scitotenv.2023.166477

2023-09-02

Abstract:The continued accumulation of halogenated organic pollutants in soil posed a potential threat to ecosystems and human health. In this study, tetrabromobisphenol A (TBBPA) was used as a typical representative of halogenated organic pollutants in soil, for alkali-thermal activated persulfate (PS) treatment. The results of response surface methodology (RSM) showed a optimal debromination efficiency of TBBPA was 88.99 % under the optimum reaction conditions. Quenching experiments and electron paramagnetic resonance (EPR) confirmed that SO 4 − •, HO•, O 2 − • and 1 O 2 existed simultaneously in the oxidation process. SO 4 − • played a major role in the initial stage of the reaction, and O 2 − • played a major role in the the last stage. Based on density functional theory (DFT) and intermediate products, two degradation pathways were proposed, including debromination reaction and β bond scission. Moreover, the basic physical and chemical properties of the soil were affected to a certain extent, while the soil surface structure, elements and functional group composition rarely changed. In addition, the T.E.S.T. analysis and biotoxicity tests proved that alkali-thermal activated PS can effectively reduce the toxicity of TBBPA-contaminated soil, which is conducive to the subsequent safe secondary utilization of soil.

environmental sciences
Sequential reduction-oxidation for photocatalytic degradation of tetrabromobisphenol A: kinetics and intermediates

Yaoguang Guo,Xiaoyi Lou,Dongxue Xiao,Lei Xu,Zhaohui Wang,Jianshe Liu

DOI: https://doi.org/10.1016/j.jhazmat.2012.09.044

2012-11-30

Abstract:C-Br bond cleavage is considered as a key step to reduce their toxicities and increase degradation rates for most brominated organic pollutants. Here a sequential reduction/oxidation strategy (i.e. debromination followed by photocatalytic oxidation) for photocatalytic degradation of tetrabromobisphenol A (TBBPA), one of the most frequently used brominated flame retardants, was proposed on the basis of kinetic analysis and intermediates identification. The results demonstrated that the rates of debromination and even photodegradation of TBBPA strongly depended on the atmospheres, initial TBBPA concentrations, pH of the reaction solution, hydrogen donors, and electron acceptors. These kinetic data and byproducts identification obtained by GC-MS measurement indicated that reductive debromination reaction by photo-induced electrons dominated under N(2)-saturated condition, while oxidation reaction by photoexcited holes or hydroxyl radicals played a leading role when air was saturated. It also suggested that the reaction might be further optimized for pretreatment of TBBPA-contaminated wastewater by a two-stage reductive debromination/subsequent oxidative decomposition process in the UV-TiO(2) system by changing the reaction atmospheres.
Degradation of bisphenol A by UV/persulfate process in the presence of bromide: Role of reactive bromine

Anhong Cai,Jing Deng,Xiao Ling,Cheng Ye,Huihong Sun,Yang Deng,Shiqing Zhou,Xueyan Li

DOI: https://doi.org/10.1016/j.watres.2022.118288

2022-05-15

Abstract:Bromide (Br-), a ubiquitous species in natural water, is capable of reacting with sulfate radical (SO4∙-) and hydroxyl radical (∙OH) to form secondary reactive bromine species (RBS). The reaction routes can influence the degradation mechanisms and performance of these radicals for removal of target pollutants and may also form harmful bromine-containing disinfection by-products (Br-DBPs) during subsequent chlorination. In the present research, the UV-activated persulfate (PS) degradation of bisphenol A (BPA) was systematically examined in the presence of Br-. Results indicated that the presence of Br-enhanced the BPA degradation and both UV/PS and UV/PS/Br- processes followed the pseudo-first-order kinetics. At 0-0.8 mM Br-, 0.2 mM Br- exerted the best enhanced effect on BPA degradation, while RBS functioned as the major contributor in the presence of 0.05-0.5 mM Br-. Solution pH (6.0-8.0) barely affected the BPA degradation in the UV/PS system, but the introduction of Br- augmented the pH dependence. In the UV/PS/Br-system, the reaction rate constant of BPA increased/decreased with increasing PS/HA dosage, and was affected slightly in the presence of bicarbonate and chloride. According to the quantum chemical calculation, the second-order rate constants of BPA with ∙OH, SO4∙-, Br∙ and Br2∙- were calculated as 7.65 × 1010, 1.67 × 109, 1.77 × 108 and 2.83 × 102 M-1 s-1, respectively. Additionally, three degradation pathways of BPA were proposed based on DFT calculation and HPLC/MS analysis, and the formed bromine-containing products exhibited higher toxicity than BPA. Br-DBPs, particularly tribromomethane and tribromoacetic acid, generated from UV/PS/Br-pre-oxidation during BPA chlorination significantly increased the toxicity of total DBPs.
Mechanochemical degradation of tetrabromobisphenol A: performance, products and pathway.

Kunlun Zhang,Jun Huang,Wang Zhang,Yunfei Yu,Shubo Deng,Gang Yu

DOI: https://doi.org/10.1016/j.jhazmat.2012.10.034

IF: 13.6

2012-01-01

Journal of Hazardous Materials

Abstract:Tetrabromobisphenol A (TBBPA) is the most widely used brominated flame retardant (BFR), which has received more and more concerns due to its high lipophilicity, persistency and endocrine disrupting property in the environment. Considering the possible need for the safe disposal of TBBPA containing wastes in the future, the potential of mechanochemical (MC) destruction as a promising non-combustion technology was investigated in this study. TBBPA was co-ground with calcium oxide (CaO) or the mixture of iron powder and quartz sand (Fe+SiO(2)) in a planetary ball mill at room temperature. The method of Fe+SiO(2) destructed over 98% of initial TBBPA after 3h and acquired 95% debromination rate after 5h, which showed a better performance than the CaO method. Raman spectra and Fourier transform infrared spectroscopy (FTIR) demonstrated the generation of inorganic carbon with the disappearance of benzene ring and CBr bond, indicating the carbonization and debromination process during mechanochemical reaction. LC-MS-MS screening showed that the intermediates of the treatment with Fe+SiO(2) were tri-, bi-, mono-brominated BPA, BPA and other fragments. Finally all the intermediates were also destroyed after 5h grinding. The bromine balance was calculated and a possible reaction pathway was proposed.
Formation of brominated by-products during the degradation of tetrabromobisphenol S by Co2+/peroxymonosulfate oxidation

Lu Wang,Yaqun Yu,Guoqiang Liu,Junhe Lu

DOI: https://doi.org/10.1016/j.jenvman.2022.115091

IF: 8.7

2022-07-01

Journal of Environmental Management

Abstract:Tetrabromobisphenol S (TBBPS), an emerging brominated flame retardant, can cause neurotoxic and cytotoxic effects to human physiology. In this study, the degradation of TBBPS in Co2+ activated peroxymonosulfate (PMS) oxidation process was explored. In particular, brominated by-products formed during the degradation of the TBBPS were examined. It was found that TBBPS could be effectively removed in the Co2+/PMS oxidation process. The pseudo-first-order rate constants were 0.13 min-1 at 0.2 mM PMS and 0.5 μM Co2+ initially. It appeared that TBBPS degradation occurred via and HO attacks, but played a dominant role. The presence of natural organic matter (NOM) greatly inhibited the transformation of the TBBPS, which can be explained by the scavenging of the radical species. β-Scission, debromination, and cross-coupling were identified as the main reaction pathways of TBBPS degradation in the Co2+/PMS system. Further oxidation and ring-opening of the intermediates generated brominated by-products including bromoform, monobromoacetic acid, and dibromoacetic acid. The formation of the brominated by-products increased gradually in approximately 48 h. But, the presence of NOM reduced the yields of the brominated -by-products. The findings of this study indicate that organic bromine contaminants can be effectively removed but lead to brominated by-products in the activated PMS oxidation process, which should be taken into consideration when -based oxidation technology is applied.

environmental sciences
Aqueous photodecomposition of the emerging brominated flame retardant tetrabromobisphenol S (TBBPS)

Haiyan Xu,Yueyue Li,Jiaxin Lu,Junhe Lu,Lei Zhou,Jean-Marc Chovelon,Yuefei Ji

DOI: https://doi.org/10.1016/j.envpol.2020.116406

IF: 8.9

2021-02-01

Environmental Pollution

Abstract:As an emerging brominated flame retardant (BFR), tetrabromobisphenol S (TBBPS) has been frequently detected in the environmental media and organisms. Knowledges on the transformation and fate of TBBPS in both environment and engineering systems are essential to its ecological risk assessment. Herein, we reported the photochemical decomposition of TBBPS in aqueous solution upon 254 nm ultraviolet irradiation (UV254). Results show that TBBPS was highly photoreactive, most likely due to the presence of four ortho-bromine substituents. The molar absorption coefficient and quantum yield of TBBPS were found to be pH-dependent, with the monoanionic form being most photoreactive. A series of photoproducts were identified by solid phase extraction (SPE) combined with liquid chromatography-electrospray ionization-triple quadrupole mass spectrometry (LC-ESI(+)-MS/MS. The photolysis of TBBPS likely proceeded through photonucleophilic substitution, photoreductive debromination, and β-scission reactions. A ketocarbene, possibly derived from the lower lying excited triplet state, was proposed to be involved in the photolysis of TBBPS. Ion chromatography analysis revealed that debromination occurred quickly, and the yield of bromide (Br−) approached 100% after 90 min irradiation. The presence of SRNOM and MRNOM inhibited the photodegradation rate of TBBPS, which is likely due to the light-screening and physical quenching effects of natural organic matter (NOM). Our results reveal that photolysis is an important process for the attenuation of TBBPS in aquatic system; however, naturally occurring species such as NOM can appreciably retard the decay of TBBPS.

environmental sciences
Degradation, metabolism, and bound-residue formation and release of Tetrabromobisphenol A in soil during sequential anoxic-oxic incubation.

Jie Liu,Yongfeng Wang,Bingqi Jiang,Lianhong Wang,Jianqiu Chen,Hongyan Guo,Rong Ji

DOI: https://doi.org/10.1021/es4014322

IF: 11.4

2013-01-01

Environmental Science & Technology

Abstract:Tetrabromobisphenol A (TBBPA) is one of the most commonly used flame retardants and has become an environmental contaminant worldwide. We studied the fate of C-14-labeled TBBPA in soil under static anoxic (195 days) and sequential anoxic (125 days)-oxic (70 days) conditions. During anoxic incubation, TBBPA dissipated with a half-life of 36 days, yielding four debromination metabolites: bisphenol A (BPA) and mono-, di-, and tribrominated BPA. At the end of anoxic incubation, all four brominated BPAs completely disappeared, leaving BPA (54% of initial TBBPA) as the sole detectable organic metabolite. TBBPA dissipation was accompanied by trace mineralization (<1.3%) and substantial bound-residue formation (35%), probably owing to chemical binding to soil organic matter. Subsequent oxic incubation was effective in degrading accumulated BPA (half-life 11 days) through mineralization (6%) and bound-residue formation (62%). However, 42% of the anoxically formed bound residues was released as TBBPA and lower brominated BPAs, which were then persistent during oxic incubation. Our results provide the first evidence for release of bound residues during alteration of the redox environment and indicate that sequential anoxic-oxic incubation approaches-considered effective in remediation of environments containing halogenated xenobiotics-do not completely remove xenobiotics from environmental matrices.
Degradation of benzothiazole pollutant by sulfate radical-based advanced oxidation process

Jie Ma,Yi Ding,Chunyun Gu,Guangyao Zhai,Yanbo Liu,Jing Wen,Xun Rong,Chaoyi Luo,Ye Qiu,Ping Zhang

DOI: https://doi.org/10.1080/09593330.2021.1906326

IF: 3.475

2021-03-30

Environmental Technology

Abstract:Benzothiazole (BTH) is an aromatic heterocyclic compound with wide industrial applications. In view of its toxicity and wide environmental presence, previous efforts have been made to decompose BTH via different degradation pathways. However, due to its recalcitrant nature, conventional biological treatment methods cannot completely degrade BTH in the wastewater. In this study, sulfate radical-based advanced oxidation process (AOP) technique has been adopted to degrade BTH in aqueous phase. Persulfate (PS) was employed as radical promotor to generate sulfate radical via heat activation. Degradation of BTH by thermally activated persulfate via AOP has been experimentally evaluated in a systematic manner. Laboratory efforts have been made to examine the impact of a number of physiochemical parameters including the type of oxidants, reaction temperature, initial concentrations of PS and BTH, solution pH, and the presence of anionic species. It shows that a higher BTH degradation rate can be achieved by lowering BTH initial concentration or increasing PS concentration. Increasing solution pH or the presence of 10 mM of Cl−, Br−, <math>CO32−</math>, or <math>HCO3−</math> species can decrease BTH degradation rate. Furthermore, the primary radical(s) responsible for BTH degradation have been identified as sulfate radical at an acidic aqueous condition, and hydroxyl radical and sulfate radical combined at a basic condition. This study provides the necessary theoretical and technical foundations for BTH degradation via sulfate radical-based AOP technique. The conclusions from this study can substantially promote the field application of AOP, especially sulfate radical-based AOP technique, for BTH degradation in wastewater treatment process.GRAPHICAL 

environmental sciences
Enhanced degradation of tetrabromobisphenol A by Fe3+/sulfite process under simulated sunlight irradiation

Zongping Wang,Lisan Cao,Ying Wan,Jingwen Wang,Fan Bai,Pengchao Xie

DOI: https://doi.org/10.1016/j.chemosphere.2021.131442

IF: 8.8

2021-12-01

Chemosphere

Abstract:Degradation of tetrabromobisphenol A (TBBPA), an emerging micropollutant, by photo/Fe3+/sulfite process was investigated under different operational conditions and water matrices. 91% of TBBPA was efficiently degraded within 30 min in the Fe3+/sulfite system under sunlight irradiation when the initial pH was 6.0, which is much higher than that of TBBPA without irradiation (52%). The acceleration of radical generation and direct photolysis by photo irradiation were responsible for the enhanced TBBPA degradation. Although this process showed better performance on TBBPA degradation in weak acid conditions, the high removal efficiency was also achieved at near-neutral pH. HO, SO4− and direct photolysis contributed to TBBPA degradation. Direct photolysis and SO4− presented the dominant contribution. The degradation rate increased with elevating the Fe3+ dose (10–40 μM), but slightly decreased when the Fe3+ dose was further raised to 100 μM. Similarly, the degradation efficiency initially increased with increasing the sulfite dose (100–400 μM), but decreased when the sulfite concentration reached 1000 μM. Dissolved oxygen played a crucial role in TBBPA degradation, the presence of water matrices such as humic acid (0.8–4.0 mg/L), bicarbonate (0.5–10 mM) and chloride (0.5–10 mM) retarded TBBPA degradation. This study proposed a new efficient strategy to enhance TBBPA degradation in the Fe3+/sulfite process.

environmental sciences
Heterogeneous catalytic reactions of in-situ generated bromide ions via hydrodehalogenation of tetrabromobisphenol A in advanced oxidation processes over palladium nanoparticles

Yang Wu,Lang Chen,Pengliang Sun,Qingran Zhang,Yinguang Chen,Xiong Zheng

DOI: https://doi.org/10.1016/j.apcatb.2023.123213

2023-08-25

Abstract:Herein, we report a novel and efficient approach for degrading tetrabromobisphenol A (TBBPA) via catalytic hydrodehalogenation (HDH) and advanced oxidation processes (AOP). Using heterogeneous catalytic HDH of TBBPA over palladium nanoparticles (Pd NPs) achieves the in-situ generation of bromide ions (Br - ), which effectively accelerate and reinforce the degradation of debromination intermediates during peroxymonosulfate-based AOP. The conversion of TBBPA to bisphenol A (BPA) by the HDH process reaches up to 99.9% debromination efficiency in 1 h under near-neutral condition, along with the removal of 99.4% BPA in 15 min during the AOP. Further studies show that free bromine and 1 O 2 produced by in-situ generated Br - reacting with peroxymonosulfate are the most effective reactive species for promoting the BPA degradation. Sustainability footprint analysis reveals considerable stability and high sustainable footprint of the integrated process during long-term operation. This work provides a promising strategy to elimination of bromine organic pollutants in water treatment.

chemistry, physical,engineering, chemical, environmental
The mechanism of photodegradation reaction of different dissociation forms of tetrabromobisphenol S in water with free radicals and the ecotoxicity evaluation of related products

Ying Lu,Se Wang

DOI: https://doi.org/10.1016/j.chemosphere.2024.141136

IF: 8.8

2024-01-09

Chemosphere

Abstract:Tetrabromobisphenol S (TBBPS) is a widely used brominated flame retardant that has attracted environmental concern due to its abundant presence in water. The objective of this study is to systematically analyze the direct photolysis and degradation mechanisms of TBBPS in two different dissociation forms in water, as well as to evaluate their toxicological effects induced by •OH, 1 O 2 , and •NO 2 radicals. The degradation mechanism of TBBPS is investigated with density functional theory (DFT) and time-dependent density functional theory (TDDFT) methods, and the toxicity of the degradation products is assessed through toxicological studies. The results of the study indicate that the OH-addition and H-abstraction reactions are favorable pathways for •OH-induced TBBPS degradation. The H-abstraction reaction of TBBPS 0 with •OH was more favorable than the •OH addition reaction. However, in the degradation of TBBPS − , the •OH addition reaction was favored over the H-abstraction reaction. Additionally, the indirect photolysis of TBBPS by 1 O 2 and •NO 2 in water was found to be easier for TBBPS − compared to TBBPS 0 , with degradation mechanisms involving Br-substitution and NO 2 -addition reactions. The higher E a values calculated indicate that the degradation of TBBPS by 1 O 2 and •NO 2 in water has been a secondary reaction. The direct photolysis reaction pathway of TBBPS in water has involved the cleavage of the S1–C7 and S1–C16 bonds. For TBBPS 0 in the S 1 /T 1 states, the primary reaction pathway is the cleavage of the S1–C16 bond, while for TBBPS − , the primary reaction pathway is the cleavage of the S1–C7 bond. Furthermore, the computational toxicology results indicate a slight increase in the toxicity levels of most products, highlighting the significance of investigating the degradation byproducts of TBBPS in greater detail.

environmental sciences
Degradation mechanisms and toxicity determination of bisphenol A by FeOx-activated peroxydisulfate under ultraviolet light

Hongbo Peng,Hongyan Gu,Zhimin Xu,Guomei Xiong,Peng Gao,Siyao Wang,Xiongchao Li,Fangfang Li

DOI: https://doi.org/10.1080/09593330.2024.2335670

IF: 3.475

2024-04-02

Environmental Technology

Abstract:Ultraviolet light (UV)-assisted advanced oxidation processes (AOPs) are commonly used to degrade organic contaminants. However, this reaction system's extensive comprehension of the degradation mechanisms and toxicity assessment remains inadequate. This study focuses on investigating the degradation mechanisms and pathways of bisphenol A (BPA), generation of reactive oxygen species (ROS), and toxicity of degradation intermediates in UV/PDS/ferrous composites (FeO x ) systems. The degradation rate of BPA gradually increased from the initial 11.92% to 100% within 120 min. Sulfate radicals ( SO4.− ), hydroxyl radicals (OH), superoxide anions ( O2.− ), and singlet oxygen ( 1 O 2 ) were the primary factors in the photocatalytic degradation of BPA in the UV/PDS/FeO x systems. The main reactions of BPA in this system were deduced to be β-bond cleavage, hydroxyl substitution reaction, hydrogen bond cleavage, and oxidation reaction. A trend of decreasing toxicity for the degradation intermediates of BPA was observed according to the toxicity investigations. The efficient degradation of BPA in UV/PDS/FeO x systems provided theoretical data for AOPs, which will improve the understanding of organic contaminants by FeO x in natural industry wastewater.

environmental sciences
Rapid Removal of Tetrabromobisphenol A by Ozonation in Water: Oxidation Products, Reaction Pathways and Toxicity Assessment.

Ruijuan Qu,Mingbao Feng,Xinghao Wang,Qingguo Huang,Junhe Lu,Liansheng Wang,Zunyao Wang

DOI: https://doi.org/10.1371/journal.pone.0139580

IF: 3.7

2015-01-01

PLoS ONE

Abstract:Tetrabromobisphenol A (TBBPA) is one of the most widely used brominated flame retardants and has attracted more and more attention. In this work, the parent TBBPA with an initial concentration of 100 mg/L was completely removed after 6 min of ozonation at pH 8.0, and alkaline conditions favored a more rapid removal than acidic and neutral conditions. The presence of typical anions and humic acid did not significantly affect the degradation of TBBPA. The quenching test using isopropanol indicated that direct ozone oxidation played a dominant role during this process. Seventeen reaction intermediates and products were identified using an electrospray time-of-flight mass spectrometer. Notably, the generation of 2,4,6-tribromophenol was first observed in the degradation process of TBBPA. The evolution of reaction products showed that ozonation is an efficient treatment for removal of both TBBPA and intermediates. Sequential transformation of organic bromine to bromide and bromate was confirmed by ion chromatography analysis. Two primary reaction pathways that involve cleavage of central carbon atom and benzene ring cleavage concomitant with debromination were thus proposed and further justified by calculations of frontier electron densities. Furthermore, the total organic carbon data suggested a low mineralization rate, even after the complete removal of TBBPA. Meanwhile, the acute aqueous toxicity of reaction solutions to Photobacterium Phosphoreum and Daphnia magna was rapidly decreased during ozonation. In addition, no obvious difference in the attenuation of TBBPA was found by ozone oxidation using different water matrices, and the effectiveness in natural waters further demonstrates that ozonation can be adopted as a promising technique to treat TBBPA-contaminated waters.
Degradation of Bisphenol A in Aqueous Solution by Persulfate Activated with Ferrous Ion.

Xiaoxuan Jiang,Yanlin Wu,Peng Wang,Hongjing Li,Wenbo Dong

DOI: https://doi.org/10.1007/s11356-013-1468-5

2013-01-01

Environmental Science and Pollution Research International

Abstract:Degradation of bisphenol A (BPA) in aqueous solution was studied with high-efficiency sulfate radical (SO4 −·), which was generated by the activation of persulfate (S2O8 2−) with ferrous ion (Fe2+). S2O8 2− was activated by Fe2+ to produce SO4 −·, and iron powder (Fe0) was used as a slow-releasing source of dissolved Fe2+. The major oxidation products of BPA were determined by liquid chromatography-mass spectrometer. The mineralization efficiency of BPA was monitored by total organic carbon (TOC) analyzer. BPA removal efficiency was improved by the increase of initial S2O8 2− or Fe2+ concentrations and then decreased with excess Fe2+ concentration. The adding mode of Fe2+ had significant impact on BPA degradation and mineralization. BPA removal rates increased from 49 to 97 % with sequential addition of Fe2+, while complete degradation was observed with continuous diffusion of Fe2+, and the latter achieved higher TOC removal rate. When Fe0 was employed as a slow-releasing source of dissolved Fe2+, 100 % of BPA degradation efficiency was achieved, and the highest removal rate of TOC (85 %) was obtained within 2 h. In the Fe0–S2O8 2− system, Fe0 as the activator of S2O8 2− could offer sustainable oxidation for BPA, and higher TOC removal rate was achieved. It was proved that Fe0–S2O8 2− system has perspective for future works.
One-step Process for Debromination and Mineralization of Tetrabromobisphenol a by a Layered Double Oxide-Supported Sulfurized Nanoscale Zero-Valent Iron under Ambient Conditions

Ruohan Li,Lixun Zhang,Ying Zhang,Zhengfang Zhang,Yuntao Guan

DOI: https://doi.org/10.1016/j.cej.2024.151165

IF: 15.1

2024-01-01

Chemical Engineering Journal

Abstract:Tetrabromobisphenol A (TBBPA), currently the most widely used brominated flame retardant, has attracted significant attention. However, traditional methods for deep debromination or mineralization of TBBPA usually include multiple steps and require external oxidants. In this study, we report a complete degradation of TBBPA through a one-step process of only adding a layered double oxide-supported sulfurized nanoscale zero-valent iron (S-nZVI@LDO) under ambient conditions. TBBPA was rapidly removed by S-nZVI@LDO with an efficiency of 95.6 % (10 mg & sdot;L-1) within 12 h. The kinetic rate constant (0.0035 min- 1) was greater when compared with traditional reductants. The produced Br- ion occupied 76.7 % of total Br content, and the concentration of total organic carbon decreased by over 50 %, suggesting a deep debromination and mineralization of TBBPA by SnZVI@LDO. It is caused by the substantial improvement of electron transfer, O2 adsorption, and hydrophobicity of S-nZVI@LDO facilitating synchronous reductive debromination and O2 activation to produce & sdot;O2- and & sdot;OH, as approved by electrochemical test, O2-TPO analysis, EPR analysis, and density functional theory calculations. The enriched structural S(-II) and enhanced Fe(III)/Fe(II) redox cycling exerted vital roles in maintaining the reduction potential of the composite. The degradation pathways analysis confirmed that debrominationmineralization mechanisms dominated the complete degradation of TBBPA. This study demonstrates the feasibility of the one-step mineralization removal of TBBPA only using S-nZVI@LDO under ambient conditions and offers insight into external oxidant-free in-situ elimination of halogenated persistent organic pollutants in a natural environment.
Evaluation of a sustained-release buccal nitroglycerin preparation in stable angina pectoris.

S. Grasso,F. Pesciatini,C. Ugolini,R. Lepore,B. Cerri

Abstract:The efficacy of a 2.5 mg sustained-release buccal nitroglycerin preparation given 8-hourly in effort-induced stable angina pectoris was investigated by means of graded exercise testing in 15 patients. An initial double-blind crossover study, compared with a placebo (duration six days) was followed by a further 15-day open treatment period on the active drug. Exercise testing was carried out 2 and 7 h after tablet administration at the conclusion of active treatment in the double-blind phase, and 2 h after tablet administration at the conclusion of the open treatment phase. Workload and exercise duration were significantly increased and mean electrocardiographic ST segment depression and ST segment recovery time significantly reduced by buccal nitroglycerin in the initial phase of the study, and these improvements were maintained over the subsequent 15-day assessment period. Systolic blood pressure at rest was significantly decreased by active treatment; other haemodynamic parameters remained unchanged. The study demonstrated the efficacy of sustained-release buccal nitroglycerin in effort-induced stable angina pectoris, and an absence of (+) tolerance to the therapeutic effects of this mode of nitrate administration.
Efficient degradation of tetrabromobisphenol A using peroxymonosulfate oxidation activated by a novel nano-CuFe 2 O 4 @coconut shell biochar catalyst

Xinxin Li,Xujing Li,Chuang Song,Xiaojin Yang,Yanping Liu,Jia Zhu

DOI: https://doi.org/10.1016/j.envpol.2023.122488

IF: 8.9

2023-10-12

Environmental Pollution

Abstract:In this study, a novel bimetallic complexation–curing nucleation–anaerobic calcination method was developed to synthesize a nano-CuFe 2 O 4 @coconut shell biochar (CuFe 2 O 4 @CSBC) catalyst to activate peroxymonosulfate for degradation of tetrabromobisphenol A (TBBPA). The reaction processes of the TBBPA on CuFe 2 O 4 @CSBC have been investigated using in situ characterization and metal leaching. The effects of initial reaction conditions and degradation mechanism were investigated. Greater than 99% degradation of TBBPA at 10 mg L −1 was achieved in 30 min under the condition of pH 11, a total organic carbon removal rate of up to 70.67% was achieved and the degradation efficiency was 90% after 5 cycles of CuFe 2 O 4 @CSBC use. The degradation was in a second-order reaction at a constant of 0.797 M −1 min −1 (R 2 = 0.993). The degradation was attributed to the main active species (SO 4 · − ≈·OH < 1 O 2 ), and the surface active site of CuFe 2 O 4 @CSBC was the key role. The degradation process involved three main degradation pathways. Path A: ·OH attacked the C–Br bonds (TBBPA→TriBBPA→DBBPA→MBBPA→BPA); Path B: Hydroxylation and decarboxylation; Path C: Dehydrocoupling of TBBPA. What's more, the practical application of the system was very positive, achieved >77% degradation in sewage and industrial wastewater.

environmental sciences

Degradation of Tetrabromobisphenol A in Heat Activated Persulfate Oxidation Process

Degradation of Tetrabromobisphenol S by thermo-activated Persulphate Oxidation: reaction Kinetics, transformation Mechanisms, and brominated By-products

Cobalt catalyzed peroxymonosulfate oxidation of tetrabromobisphenol A: Kinetics, reaction pathways, and formation of brominated by-products

Elimination of Bisphenol A with Visible Light-Enhanced Peroxydisulfate Activation Process Mediated by Fe3+-nitrilotriacetic Acid Complex.

Alkali-thermal activated persulfate treatment of tetrabromobisphenol A in soil: Parameter optimization, mechanism, degradation pathway and toxicity evaluation

Sequential reduction-oxidation for photocatalytic degradation of tetrabromobisphenol A: kinetics and intermediates

Degradation of bisphenol A by UV/persulfate process in the presence of bromide: Role of reactive bromine

Mechanochemical degradation of tetrabromobisphenol A: performance, products and pathway.

Formation of brominated by-products during the degradation of tetrabromobisphenol S by Co2+/peroxymonosulfate oxidation

Aqueous photodecomposition of the emerging brominated flame retardant tetrabromobisphenol S (TBBPS)

Degradation, metabolism, and bound-residue formation and release of Tetrabromobisphenol A in soil during sequential anoxic-oxic incubation.

Degradation of benzothiazole pollutant by sulfate radical-based advanced oxidation process

Enhanced degradation of tetrabromobisphenol A by Fe3+/sulfite process under simulated sunlight irradiation

Heterogeneous catalytic reactions of in-situ generated bromide ions via hydrodehalogenation of tetrabromobisphenol A in advanced oxidation processes over palladium nanoparticles

The mechanism of photodegradation reaction of different dissociation forms of tetrabromobisphenol S in water with free radicals and the ecotoxicity evaluation of related products

Degradation mechanisms and toxicity determination of bisphenol A by FeOx-activated peroxydisulfate under ultraviolet light

Rapid Removal of Tetrabromobisphenol A by Ozonation in Water: Oxidation Products, Reaction Pathways and Toxicity Assessment.

Degradation of Bisphenol A in Aqueous Solution by Persulfate Activated with Ferrous Ion.

One-step Process for Debromination and Mineralization of Tetrabromobisphenol a by a Layered Double Oxide-Supported Sulfurized Nanoscale Zero-Valent Iron under Ambient Conditions

Evaluation of a sustained-release buccal nitroglycerin preparation in stable angina pectoris.

Efficient degradation of tetrabromobisphenol A using peroxymonosulfate oxidation activated by a novel nano-CuFe 2 O 4 @coconut shell biochar catalyst