Abstract:Loop heat pipe (LHP) is an efficient phase-change heat transfer device which has been widely applied in cooling high-power electronics on ground and in spacecraft. In previous work, a novel LHP coupled with vapor-driven jet injector (VDJI) has been proved to be feasible and shows excellent performance, namely LHPI. However, due to the lack of pressure data during LHP operation, the coupling mechanisms of VDJI and LHP remain unknown. Especially, the heat-mass transfer between high-speed vapor and subcooled liquid inside VDJI, which has great influence on the LHPI, need to be investigated to guide the design of the LHPI. In this paper, the start-up process, steady-state operation characteristic of LHPI and internal flow field of VDJI were investigated experimentally and numerically. By using the pore-forming sintering and integrated sintering method, the bi-porous wick was prepared and embedded on the base plate surface of evaporator, which brought a significant improvement in its performance. The results indicated that the LHPI could operate under a power of 600 W (50.0 W/cm 2 ) without dry-out. Maintaining the heating wall temperature within 85 °C, the minimum thermal resistance of the LHPI with bi-porous and integrated sintered wick was below 0.18, and the maximum heating power can reach up to 404 W, which are 60% lower and 52.5% higher than mono-porous wick, respectively. In addition, four operation modes of VDJI were classified as low-efficiency mode, normal-injection mode, restricted expansion mode and superheated mode. The operation modes of VDJI had great influence on the performance of LHPI. In normal-injection mode, the entrainment ratio of VDJI exceeded 100, which resulted in the lowest thermal resistance of LHPI. For long-term operation of LHPI, the VDJI is suggested keep operating in normal-injection mode. Moreover, by using 3D numerical simulation method, the internal flow structure of the VDJI was obtained to gives an insight into mechanisms of these four operation modes. The numerical results showed the profile of compression waves and confirmed the existence of condensation shock wave in VDJI.

Development of a Loop Heat Pipe with the 3D Printed Stainless Steel Wick in the Application of Thermal Management

The Start-Up Characteristics of a Novel Loop Heat Pipe with Stainless Steel Capillary Wick

Performance of LHPs with a Novel Design Evaporator

Simulation of Steady-State Operation of an Ejector-Assisted Loop Heat Pipe with a Flat Evaporator for Application in Electronic Cooling

Three-dimensional Lattice Boltzmann Investigation on Pore Scale Liquid–vapor Distribution Patterns and Heat Transfer Performance of a Loop Heat Pipe Heterogeneous Porous Wick Evaporator

Experimental research on the thermal performance of a flat evaporator loop heat pipe with a new composite wick

Experimental Investigation and Visual Observation of Loop Heat Pipes with Two-Layer Composite Wicks

Experimental investigation on the thermal performance of a novel loop heat pipe (LHP) with micro-channel structure

Biomimetic porous wick with efficient fluid transport and excellent heat transfer for loop heat pipes

Effect of the working fluid transportation in the copper composite wick on the evaporation efficiency of a flat loop heat pipe

Experimental studies on a high performance compact loop heat pipe with a square flat evaporator

Comparative Study on Thermal Performance of Ultrathin Miniature Loop Heat Pipes with Different Internal Wicks

Experimental study on a novel loop heat pipe with both flat evaporator and boiling pool

Experimental Study of a Novel Loop Heat Pipe with a Vapor-Driven Jet Injector and a Boiling Pool

Performance of a novel loop heat pipe coupled with micro vapor-driven jet injector – An experimental and numerical study

Experimental Research on the Heat Performance of a Flat Copper-Water Loop Heat Pipe with Different Inventories

Experimental study on capillary performance of sintered powder porous wick for loop heat pipes

Development of Sintered Ni-Cu Wicks for Loop Heat Pipes

Experimental study on the characteristics of loop heat pipe with modified carbon fiber felt wick

Experimental investigation on the start-up performance of a novel flat loop heat pipe with dual evaporators

Experimental investigation for the loop heat pipe with a bifacial flat evaporator