Abstract:{1011}-{1012} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy, especially at low or moderate rolling temperature. Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150°C and 300°C respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively: the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling. Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector, and their mechanical performances are measured by uniaxial tensile tests at room temperature and a strain rate of 0.001 s -1. Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropies. The effects of the {1011}-{1012} double twins occurred during rolling on the microstructure, texture and mechanical properties of the rolled sheets are discussed and related to each other. The results show that the fraction of {1011}-{1012} double twins varies widely in different rolled sheets, which are determined by the rolling temperature. The twins in different rolled sheets are arranged in different ways. In the normal rolled sheets, the traces of twins are approximately perpendicular to the final rolling direction, while in the cross rolled sheets there are both traces of twins parallel and to the final directions. This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction. For the same reason, the textures of twins in the rolled sheets produced through different paths are different. The textures of twins will add onto the bulks, and increases the textural difference between the bulks. The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins. © Right.

MECHANICAL PROPERTIES AND ANISOTROPY OF MG ALLOY WITH TWIN LAMELLAE

Improving Tensile and Compressive Properties of Magnesium Alloy Plates by Pre-Cold Rolling

Effect of Rolling Technology on Microstructure and Mechanical Properties of Mg Alloy for Automobile

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

Mechanical Properties and Anisotropy of AZ31 Alloy Sheet Processed by Flat Extrusion Container

The improvement on mechanical anisotropy of AZ31 magnesium alloy sheets by multi cross-rolling process

Heterogeneous Lamella Mixed Grain Structures of Strength-Ductility Synergy in Medium Strain Rate Rolled AZ31 Magnesium Sheets

Development of Mechanical Properties in AZ31 Magnesium Alloy Processed by Cold Dynamic Extrusion

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

Microstructure and Mechanical Properties of Mg-Gd-Y-Zn-Mn Alloy Sheets Processed by Large-Strain High-Efficiency Rolling

Twinning, Grain Orientation, and Texture Variations in Mg Alloy Processed by Pre-Rolling

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Effects of Micro-Twin Lamellar Structure on the Mechanical Properties and Fracture Morphology of AZ31 Mg Alloy

Microstructure, Texture and Mechanical Properties Evolution of Pre-Twinning Mg Alloys Sheets During Large Strain Hot Rolling

On the Structure, Mechanical Behavior, and Deformation Mechanism of Az91 Magnesium Alloy Processed by Symmetric and Asymmetric Rolling

Microstructure and mechanical property of multi-pass low-strain rolled Mg-Al-Zn-Mn alloy sheet

Activation of multiple twins by pre-tension and compression to enhance the strength of Mg–3Al–1Zn alloy plates

Enhanced mechanical properties of AZ91 magnesium alloy by asynchronously large-strain high-efficiency rolling with bimodal grain structure

Microstructure Evolution and Mechanical Properties of High-Strength Mg-Gd-Y-Zn-Mn Alloy Processed by Asymmetric Hot Rolling

Effect of Dual Deformation Processes on the Microstructure and Mechanical Properties of Low-Alloyed Mg-Zn-Ca-Mn Alloy

Mechanical Behavior and Microstructural Evolution in Rolled Mg-3Al-1Zn-0.5Mn Alloy under Large Strain Simple Shear