Abstract:The stacking fault energy (SFE) of face-centered cubic (FCC) alloys is a critical parameter that controls microstructural and crystallographic texture evolution during deformation and annealing treatments. This review focuses on several FCC alloys, aluminum (Al), copper (Cu), austenitic stainless steels (ASSs), and high entropy alloys (HEAs), all of which exhibit varying SFEs. These alloys are often subjected to thermo-mechanical processing (TMP) to enhance their mechanical properties. TMP leads to the evolution of deformation-induced products, such as shear bands (SBs), strain-induced martensite (SIM), and mechanical/deformation twins (DTs) during plastic deformation, while also influencing crystallographic texture. High-medium SFE materials, such as Al and Cu, typically exhibit the evolution of Copper-type texture during room temperature rolling (RTR), while low SFE materials, such as ASSs and HEAs, display Brass-type texture at high reduction ratios. Moreover, the presence of second-phase particles/precipitates can also impact the microstructure and texture evolution in Al and Cu alloys. Particle-stimulated nucleation (PSN) during the annealing treatment has been reported for Al, Cu, ASSs, and HEAs, which causes texture weakening. Another interesting observation in severely deformed Cu alloys is the room-temperature softening phenomenon, which is discussed in the reviewed work. Additionally, plastic deformation and heat treatment of ASSs result in phase transformation, which was not observed in Al, Cu, or HEAs. Furthermore, the dependence of special boundaries in HEAs on plastic deformation temperature, strain rate, and annealing temperature is also discussed. Thus, this review comprehensively reports on the impact of TMP on microstructural and crystallographic texture evolution during plastic deformation and the annealing treatment of Al, Cu, ASSs, and HEAs FCC materials, using results obtained from electron microscopy.

Structural Evolutions of Metallic Materials Processed by Severe Plastic Deformation

Achieving High Strength and High Ductility in Nanostructured Metals: Experiment and Modelling

Nanostructural design of superstrong metallic materials by severe plastic deformation processing

Research Progress on the Microstructure Evolution Mechanisms of Al-Mg Alloys by Severe Plastic Deformation

Constitutive modeling of mechanical behaviors in gradient nanostructured alloys with hierarchical dual-phased microstructures

New Insight for Mechanical Properties of Metals Processed by Severe Plastic Deformation

Nanostructuring of Zn–Li-based alloys through severe plastic deformation: Microstructure, mechanical properties, and corrosion behaviors

Fabrication of Nano/Ultra-Fine Grained IF Steel via SPD Processes: a Review

Review: nanoSPD-produced metallic materials for advanced medical devices

Microstructure and Texture Evolution in Thermomechanically Processed FCC Metals and Alloys: a Review

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Mechanical properties and deformation mechanisms of gradient nanostructured metals and alloys

SPD deformation of pearlitic, bainitic and martensitic steels

The Superstrength of Nanostructured Metallic Materials: Their Physical Nature and Hardening Mechanisms

Microstructure refinement, strengthening and ductilization mechanisms in Al–Mg–Mn–Er–Zr alloy with high Mn content by friction stir processing

Deformation mechanisms and mechanical properties of the high-strength and ductile Al-Zn-Mg-Cu alloys processed by repetitive continuous extrusion forming process with different heat treatments

Effect of Deformation on Precipitation and the Microstructure Evolution during Multistep Thermomechanical Processing of Al-Zn-Mg-Cu Alloy

Superfunctional Materials by Ultra-Severe Plastic Deformation

Structure–Phase Transformations and Properties of Non-Ferrous Metals and Alloys under Extreme Conditions

Atomistic modeling of idealized equal channel angular pressing process

Experimental and numerical analyses of 45 steel during three dimensional severe plastic deformation (3D-SPD)