Abstract:Multi-stage microforming is increasingly used in manufacturing of the miniaturized parts with complex structures and geometries. Optimization design of this type of manufacturing process, however, is still challenging due to its unknown intrinsic nature of the process. In the multi-stage deformation and microforming, the size effect (SE), the strain path change (SPC), and the intragranularly misoriented grain boundary (IMGB) generated in previous forming stage, are the main factors governing the deformation behaviors of ultra-thin sheets. To gain thorough insights into their influences on deformation and elucidate the associated micro-scaled mechanisms, SS 316L ultra-thin sheets with the thickness of 0.1 mm and different mean grain sizes (d) were used for two-stage tensile tests under the conditions with distinct pre-strain & epsilon;pre and intersection angle & theta;SPC (the angle between the previous loading direction and subsequent one). Mechanical tests reveal that increasing & epsilon;pre and & theta;SPC reduces the yield stress and hardening rate in SPC tension, but this reduction gets smaller after increasing d. This is because more IMGBs with complex pattern are formed in relatively large grains, raising the permanent deformation resistance inside grains in subsequent tension. To model the IMGB-induced hardening, the SPC-induced softening, and the SE-induced concurrent facilitations to the hardening and softening, an enhanced crystal plasticity constitutive relation was established. The physical essence that IMGB obstructs dislocation movement, is used to model the IMGB-induced hardening based on the interactions between the main slip planes and IMGBs. The hardening facilitation caused by increasing grain size is implicitly incorporated in determining the saturated slip resistance. Modelling of the SPC-induced softening is based on the high Schmid factor grain fraction and its influences are governed by pre -strain and the defined SPC parameter. The softening facilitation caused by coarsening grains is modelled in establishing the initial slip resistance in SPC deformation. The proposed simulation procedure and constitutive relationship help with accurately predicting the mechanical response and microstructure evolution in micro-scaled SPC deformation, and also provide a basis for modelling and design of the multi-stage microforming of complex miniaturized parts.

Finite Element Simulation of Mesoscale Inhomogeneous Deformation in 304 Stainless Steel Foil Tensile

3D Crystal Plasticity Finite Element Modeling of the Tensile Deformation of Polycrystalline Ferritic Stainless Steel

Crystal Plasticity Simulation of Yield Loci Evolution of SUS304 Foil

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

SIMULATION OF STORED ENERGY EVOLUTION IN HOT DEFORMED AUSTENITE ON A MESOSCALE

Specimen Dimension and Grain Size Effects on Deformation Behavior in Micro Tensile of Sus304 Stainless Steel Foil

A Constitutive Model for Metal Plastic Deformation at Micro/meso Scale with Consideration of Grain Orientation and Its Evolution

Surface roughness evolution and heterogeneous plastic deformation of austenitic stainless steel during micro deep drawing: Modeling and experiment

Finite Element Modeling of Tensile Instability of Sheet Metals Considering Nonuniform Mechanical Properties

A Multiscale Constitutive Model Coupled with Martensitic Transformation Kinetics for Micro-Scaled Plastic Deformation of Metastable Metal Foils

Crystal Plasticity Finite Element Method for Slip Systems Evolution Analysis of / Duplex Titanium Alloys during Quasi-Static Tensile Testing

Effect of Plastic Anisotropy on Microscale Ductile Fracture and Microformability of Stainless Steel Foil

FEM simulations of tensile deformation and fracture analysis for CuW alloys at mesoscopic level

Crystal Plasticity-Based Analysis and Modelling of Grain Size and Strain Path Dependent Micro-Scaled Deformation Mechanisms of Ultra-Thin Sheet Metals

Multi-scale Crystal Plasticity Finite Element Method (CPFEM) Simulations for Shear Band Development in Aluminum Alloys

Microstructure evolution in 439 stainless steels under tensile: phase field simulation and experiment

Anisotropic plasticity deformation during micro-deep drawing of 304 foils: An experimental and numerical investigation

Prediction of anisotropic deformation behavior of TA32 titanium alloy sheet during hot tension by crystal plasticity finite element model

Microstructure characterization and crystal plastic finite element simulation of additive manufacturing 316 L stainless steel

Simulation of Torsion of Thin FCC Single Crystal Wires by Mechanism-Based Strain Gradient Crystal Plasticity

Crystal Plasticity Finite-Element Simulation of Ti-6Al-4V Alloy with 3D Polycrystalline Models