Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

Effect of Annealing Process on the Abnormal Grain Growth Behavior During Carburizing of 20crmnti Steel

Nucleation and Coarsening Behavior of Aluminum Nitride and Its Effect on Abnormal Grain Growth in High-Temperature Carburizing Process

Effect of Initial Microstructure on Austenite Transformation and Grain Growth Behavior of 20crmnti Steel During Pseudo-Carburizing Process

Precipitation Criterion for Inhibiting Austenite Grain Coarsening During Carburization of Al-Containing 20cr Gear Steels

Effect of the Normalizing Temperature on the Size and Homogeneity of Austenite Grain in 20CrMnTi Carburized Gear Steel

Suppression of Austenite Grain Coarsening by Using Nb–Ti Microalloying in High Temperature Carburizing of a Gear Steel

Effect of Precipitated Particles on Austenite Grain Growth of Al- and Nb-Microalloyed 20MnCr Gear Steel

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

On the grain coarsening behavior of 20CrMnTi gear steel during pseudo carburizing: A comparison of Nb-Ti-Mo versus Ti-Mo microalloyed steel

Effect of carburizing process parameters on austenitic grain coarsening behavior of common carburizing steel

Effect of Precipitates on Austenite Grain Growth Behavior in a Low-Carbon Nb-V Microalloyed Steel

Abnormal Grain Growth Induced by Cyclic Heat Treatment in TiAL Alloy

Austenite Growth Behavior and Prediction Modeling of Ti Microalloyed Steel

Effect of Preheat Treatment Process on Austenite Grain Growth Behavior in Gear Steel SCr420H for High Temperature Carburization

Prediction Of The Formation Of Carbide Network On Grain Boundaries In Carburizing Of 18crnimo7-6 Steel Alloys

Effect of Preheat Treatment on Microstructure and Properties of a Gear Steel for High‐Temperature Carburizing

The Influence of Precipitate Morphology on the Growth of Austenite Grain in Nb-Ti-Al Microalloyed Steels

Effect of Austenitizing Condition on Abnormal Grain Growth in T122 Heat-Resistant Steel

The Effect of Network Cementite Dissolution on the Nucleation and Growth of Prior Austenite Grains in High Carbon Low Alloy Steels

Precipitation And Evolution Behavior Of Carbide During Heat Treatments Of Gcr15 Bearing Steel

Effect of Heat Treatment Process on Microstructure and Crystallography of 20crmntih Spur Bevel Gear