Abstract:In view of the potential demand for the materials with excellent dynamic mechanical behavior in protective construction, the dynamic tensile mechanical properities and deformation mechanism of twinning-induced plasticity (TWIP) steel at various high strain rates were investigated in this paper by combining test research and numerical simulation. In order to explore the impact of strain rates on mechanical behaviors within the tested range, a split Hopkinson tensile bar (SHTB) was utilized to measure the mechanical responses of TWIP steel ranging from 1000 s -1 to 6500 s -1 . The Johnson-Cook (J-C) dynamic constitutive model was established based on the mechanical test results, and the mechanical properties were studied by using ANSYS/LS-DYNA. EBSD and TEM were employed to investigate the microstructure evolution of TWIP steel under dynamic loading. The results demonstrate that both strength and plasticity increase with increasing strain rate, demonstrating positive strain rate sensitivity (PSRS) which is primarily due to the activation of multiple twin systems at higher strain rates. As the strain rate increases, the mean free path of dislocation slip reduces, causing a higher strain hardening rate. The critical shear stress required for twinning is almost unchanged with an increase in strain rate, while the shear stress required for dislocation increases consistently. As the strain rate exceeds 3000 s -1 , the critical shear stress required for dislocation becomes greater than that for twinning. With increasing strain rate, the proportion of secondary twins in TWIP steel rises and the deformation twins are bent when the strain rate is 6500 s -1 owing to the effect of dislocations and stacking faults. The production of nanoscale twins at higher strain rates is a beneficial phenomenon, as it enhances both strength and plasticity. The deformation twins become thinner with an increase in strain rate, leading to a rise in the stress needed for the motion of dislocations to pass the twins, which contributes to the improvement of strength in TWIP steel. The slip systems that deforms at a disadvange have new orientations because of defromation twins. The established J-C model is appropriate well for analyzing the mechanical properties of TWIP steel in the tested range of strain rates accoring to the fingdings of test and numerical simulation. Establishing the connection of microstructure and macroscopic behavior of TWIP steel could provide a guidance for the its further study and the application in the fields of impact resistance and anti-explosion.

Mechanical behavior of DP780 dual phase steel at a wide range of strain rates

Tensile Mechanical Behaviour of Ultra-High Strength Cold Rolled Dual Phase Steel DP1000 at High Strain Rates

Dynamic deformation behavior and corresponding constitutive model of ultra-high strength DP1000 steel

Understanding the damage initiation and growth mechanisms of two DP800 dual phase grades

Effect of martensite morphology and volume fraction on strain hardening and fracture behavior of martensite–ferrite dual phase steel

A Rate-Dependent Model for Metals Based on a Master Curve of Normalized Hardening Behavior of DP Steels

On the use of thermomechanical processing to enhance the strength-ductility-toughness balance of plain low-carbon steel

0610 A Comparative Study on Gao-Zhang and Johnson-Cook Constitutive Models

Investigation of evolving yield surfaces of dual-phase steels

Investigation of dynamic tensile mechanical responses and deformation mechanism at high strain rates in a TWIP steel

Fracture of dual phase steel sheets under uniaxial tension (I): experimental study with dic techniques

On the Simultaneous Improving of Strength and Elongation in Dual Phase Steels via Cold Rolling

Semi in-situ investigations on deformation-induced micro-damage in high-strength dual-phase steels

Effect of compressive load on texture evolution and anisotropic behavior of dual-phase steel under biaxial loading in complete σ 11 -σ 22 space

Deformation behavior and microstructure evolution of 300M ultrahigh strength steel subjected to high strain rate: an analytical approach

On the mechanical heterogeneity in dual phase steel grades: Activation of slip systems and deformation of martensite in DP800

A rate-dependent damage mechanics model for predicting plasticity and ductile fracture behavior of sheet metals at high strain rates

Investigation of the History-dependent Nonlinear Micro-viscoplasticity Behavior of Dual-phase Steel using Crystal Plasticity Finite Element Method

Achieving High Strength and High Ductility of Dual-Phase Steel Via Alternating Lamellar Microstructure

Damage Evolution in Complex-Phase and Dual-Phase Steels during Edge Stretching

Temperature Dependency of Modified Mohr–Coulomb Criterion Parameters for Advanced High Strength Dual-Phase Steel DP780