Abstract:Grain boundaries (GBs) are known to have an important influence on material properties, so understanding how GBs in graphene change its physical properties is important both scientifically and technologically. In this paper, we perform a series of molecular dynamics simulations to investigate the energies, mechanical properties and fracture process of 29 graphene GBs (symmetric and nonsymmetric) under tensile strains. With different arrangements of the pentagonal and heptagonal rings, the misorientation angle () ranges from 3.5 to 27.8. The GBs defects in graphene can produce a pre-strain that will lead to an increase of the energy of GBs. We study the atomic energy distribution around GBs and define a new parameter: single defect energy (Esingle) to calculate the average energy per GBs defect. It is found that Esingle shows a clear linear relation between and defect density (), because pre-strain filed can be cancelled out locally with the increase of defect density. And this pre-stain can reduce the strength of the C-C bond contained in GBs defects. Hence, with very few exceptions, mechanical failure always starts from the defective region. Furthermore, the energy of GBs can be used to reflect the strength of GBs indirectly. The simulated results show that the tensile strength of GBs is linearly related to the highest atomic energy (Emax), and it also depends on Esingle monotonically. Owing to the pre-strain, load distribution along GBs is uneven. Because some bonds are stretched while others are compressed, that is, the real number of bearing carbon bonds is less than the nominal number. Therefore, at the beginning of tension, the Young's modulus of polycrystalline graphene is significantly lower than that of the monocrystal one. But with the increase of strain, it becomes comparable to that of the monocrystal graphene at sufficiently large strain. The results of fracture process indicate that formation and propagation of crack are both dependent on strength GBs. For low GB strength, the fracture mechanism is transgranular fracture in the form of direct fracture of C-C bonds. When stress reaches a critical value, the weakest C-C bonds in GBs will breakdown and form a fracture site. Because of the uneven bearing condition, the C-C bonds in front of the crack possess considerable residual strength and could prevent crack from propagating. As a result, many other fracture sites in the GBs defect can be produced with the increase of strain, and finally, these sites emerge gradually along GBs and form a sawtooth crack. In contrast, the fracture process of high strength GBs is always accompanied with the variations of Stone-Wales (S-W) transformation and direct fracture of C-C bonds. Once the fracture site forms, the crack will propagate rapidly predominantly along armchair or zigzag direction and finally could cross GBs, this process can be called intergranular fracture. Our present work provides fundamental guidance for understanding how defects affect the mechanical behaviour, which is important for further research and application of graphene devices.

Mechanical strength in hierarchically polycrystalline graphene with dislocation arrays-embedded grains

Enhancing the Strength of Graphene by a Denser Grain Boundary.

On the Role of Hierarchical Twins for Achieving Maximum Yield Strength in Nanotwinned Metals

Pseudo Hall-Petch Strength Reduction In Polycrystalline Graphene

Role of defects and geometry in the strength of polycrystalline graphene

Molecular Dynamics Study of the Tensile Mechanical Properties of Polycrystalline Graphene

The Nature of Strength Enhancement and Weakening by Pentagon–heptagon Defects in Graphene

Defect-activated self-assembly of multilayered graphene paper: A mechanically robust architecture with high strength

Inverse Pseudo Hall-Petch Relation in Polycrystalline Graphene

Mechanical properties of crystalline-amorphous composites: generalisation of Hall-Petch and inverse Hall-Petch behaviours

Anisotropic mechanical properties of monolayer fullerene network: An interplay between two types of interfullerene bonds

Yielding and jerky plasticity of tilt grain boundaries in high-temperature graphene

Hydrogenated Grain Boundaries Control the Strength and Ductility of Polycrystalline Graphene

Strengthening Mechanism in Micro-Polycrystals with Penetrable Grain Boundaries by Discrete Dislocation Dynamics Simulation and Hall–Petch Effect

Peridynamic Simulation of Fracture in Polycrystalline Graphene

Investigation of Grain Boundary and Orientation Effects in Polycrystalline Metals by a Dislocation-Based Crystal Plasticity Model

Strengthening effect of high-entropy alloys endowed by monolayer graphene

Mechanical Deformation and Fracture Mode of Polycrystalline Graphene: Atomistic Simulations

Molecular dynamics simulation of dislocation network formation and tensile properties of graphene/TiAl-layered composites

Grain-Size-Controlled Mechanical Properties of Polycrystalline Monolayer MoS2

Analysis of the Twin Spacing and Grain Size Effects on Mechanical Properties in Hierarchically Nanotwinned Face-Centered Cubic Metals Based on A Mechanism-Based Plasticity Model