Abstract:In this study, the crystalline morphology and mechanical property of Olefin Block Copolymer (OBC) were tailored by adding a small amount (up to 10 wt%) of ultrahigh molecular weight polyethylene (UHMWPE). To do this, OBC and UHMWPE was solution blended first and then subjected to compression molding or injection molding, respectively. It was found that a small quantity of UHMWPE (0.5 wt%, 1 wt %) can be fully mixed with OBC, while phase separation occurs when UHMWPE content is higher than 2.5 wt%, as suggested by SEM and DSC results. For compression molded samples, an obvious increase of Young's modulus from 12 MPa to 22 MPa while maintaining the good elasticity of OBC was observed as the content of UHMWPE is less than 2.5 wt% (in the phase miscible range). With further increasing of UHMWPE content to 10 wt%, only slightly increased Young's modulus is seen. Thus the miscibility between OBC and UHMWPE plays an important role in determining the mechanical property for compression molded samples. However, a continuous increase of Young's modulus was observed with the increase of UHMWPE content for samples obtained via injection molding, with a slight increase (from 23 MPa to 40 MPa) as the content of UHMWPE is less than 2.5 wt%, while with a large increase (from 40 MPa to 156 MPa) as the content of UHMWPE increases from 2.5 wt% to 10 wt, accompanied with a greatly decrease of elongation (from 1100% to 50%). Even elastomer-to-plastic transition takes place when the content of UHMWPE is large (5 wt%, 10 wt%). Structural analysis of injection-molded samples shows that shish-kebab-like structures can be successfully induced as addition of UHMWPE along with gradually increased crystal orientation. It was interesting to find that small-addition of UHMWPE favors increased tie-effect due to the miscibility between OBC and UHMWPE, which is helpful to the elasticity retaining as well as strength enhancement, while large-addition of UHMWPE gives rise to phase separation and mixed shish-kebabs (OBC/UHMWPE hybrid shish-kebabs and UHMWPE homo-shish-kebabs), leading to elastomer-to-plastic transition. (C) 2016 Elsevier Ltd. All rights reserved.

Improved Performance and Crystallization Behaviors of Bimodal HDPE/UHMWPE Blends Assisted by Ultrasonic Oscillations

Study on synergistic toughening of polypropylene with high-density polyethylene and elastomer-olefin block copolymers under ultrasonic application

Improved Performance Balance of Polyethylene by Simultaneously Forming Oriented Crystals and Blending Ultrahigh-Molecular-Weight Polyethylene

Effect of solid-state shear milling on structure and properties of HDPE/UHMWPE blends

Effect of small amount of ultra high molecular weight component on the crystallization behaviors of bimodal high density polyethylene

THE EFFECT OF ULTRASONIC OSCILLATIONS ON PROPERTIES AND MORPHOLOGY OF POLYAMIDE-6/HIGH-DENSITY POLYETHYLENE BLENDS

Constructing Highly Oriented and Condensed Shish-Kebab Crystalline Structure of HDPE/UHMWPE Blends Via Intense Stretching Process：achieving High Mechanical Properties and In-Plane Thermal Conductivity

Effects of Addition of Ultra-High Molecular Weight Polyethylene on Tie-Molecule and Crystallization Behavior of Unimodal Pe-100 Pipe Materials

Dynamic rheological properties of high-density polyethylene/polystyrene blends extruded in the presence of ultrasonic oscillations

Evolution of the cavity structure of HDPE/UHMWPE blends during cold stretching

Short-time fabrication of well-mixed high-density polyethylene/ultrahigh-molecular-weight polyethylene blends under elongational flow: morphology, mechanical properties and mechanism: Fabrication and performance of HDPE/UHMWPE blends under elongational flow

Tailoring the Crystalline Morphology and Mechanical Property of Olefin Block Copolymer Via Blending with a Small Amount of UHMWPE

Constructing highly oriented and condensed shish-kebab crystalline structure of HDPE/UHMWPE blends via intense stretching process:Achieving high mechanical properties and in-plane thermal conductivity

Synergistic toughening of polypropylene with ultra-high molecular weight polyethylene and elastomer-olefin block copolymers

Hierarchical structure manipulation of UHMWPE/HDPE fibers through in-reactor blending with Cr/V bimetallic catalysts

Effects of Different Ultrahigh Molecular Weight Polyethylene Contents on the Formation and Evolution of Hierarchical Crystal Structure of High‐density Polyethylene/ultrahigh Molecular Weight Polyethylene Blend Fibers

Structure and Tensile Properties Change of LDPE/UHMWPE Blends Via Solid State Shear Milling

The influence of UHMWPE with varying morphologies on the non-isothermal crystallization kinetics of HDPE

HDPE/UHMWPE in Vibration Field and Property of Its Blown Film

Linear Viscoelastic Properties of High‐density Polyethylene/polyamide‐6 Blends Extruded in the Presence of Ultrasonic Oscillations

Cocrystallization Behavior of Hdpe/Uhmwpe Blends Prepared by Two-Step Processing Way