Abstract:Due to the easiness of removing source singularity, the primary/secondary field algorithm is one of popular algorithms for three-dimensional modelling in geophysical electromagnetic methods. However, it is cumbersome to implement this algorithm if a transmitting source is laid on a rugged surface of the Earth or background models are complex. The total field algorithm is an alternative scheme to numerically simulate the electromagnetics, and its difficulty is how to enforce the source item in the Helmholtz equation of electric field or its magnetic vector potential, especially observation points are located near the transmitting source. In controlled-source electromagnetic methods, transmitting sources including a long grounded wire can be viewed as a combination of many horizontal electric dipoles (HEDs). In our three-dimensional scheme, the source item in the Helmholtz equation of total electric field, the governing equation for vector finite element (FE) method, could be dealt with in the form of HED. The numerical accuracy of FE method depends on meshing quality to some extent, which is evaluated by the maximum allowable radius-edge ratio and the minimum allowable dihedral angle for the unstructured tetrahedral elements generated by the TetGen software. Taking the electric field excited by a HED within a 0. 01 S . m(-1) whole-space as examples, the results show that as the maximum allowable radius-edge ratio decreases or the minimum allowable dihedral angle increases, the numerical accuracy will be improved. By this model, we also validated the algorithm presented here. For a conductive prism buried in a homogeneous half-space with a 100m-long grounded wire, the electric field calculated by our algorithm was compared with those calculated by the integral equation method based on secondary electric field, the finite volume method based on total electric field and the FE method based on magnetic vector potential. The results show that these four numerical solutions coincide well with each other, and the behavior of the electric field well indicates the conductive prism. Then, we applied the algorithm presented here to compute the amplitude and phase of the electric field for the model of disc-shape hydrocarbon buried in seabed. Through this model, the validity and ability of modelling the electromagnetic field for irregular bodies were tested simultaneously. Finally, an inclined fault, contact zone and metalliferous vein are always approximated by an inclined plate in three-dimensional modelling. For the inclined plate model with different conductivities, the electric field excited by a 1000m-long grounded wire source was calculated. The electric field for the inclined plate of 0. 0333 S. m(-1) has stronger anomaly responses than those for the inclined plate of 0. 0167 S . m(-1). In the following study, this algorithm will be applied to three-dimensional modelling for a long grounded wire source laid on a rugged surface.

A vector finite element solver of three-dimensional modelling for a long grounded wire source based on total electric field

Two-dimensional Magnetotelluric Modelling by the Boundary Element Method.

Forward modeling method of 2D transient electromagnetic field induced by line source

FINITE ELEMENT METHOD FOR MODELING RESISTIVITY SOUNDING ON 3-D GEOELECTRIC SECTION

Massively Parallel Simulation Of Large-Scale Electromagnetic Problems Using One High-Performance Computing Scheme And Domain Decomposition Method

A general forward solver for 3D CSEMs with multitype sources and operating environments

3D finite-difference transient electromagnetic modeling with a whole-space initial field

3D frequency-domain modeling of marine controlled source electromagnetic responses with topography using finite volume method

Forward Calculation of 3D Controlled-Source Electromagnetic Responses Based on Joint Application of Secondary Field and Coupled Potential Formulations

An h-Adaptive Finite Element Modeling of the 2.5-Dimensional Point Source Electricfield

Grounded source transient electromagnetic 3D forward modeling with the spectral-element method and its application in hydraulic fracturing monitoring

Electromagnetic Field Of A Horizontal In-Finitely Long Magnetic Line Source Over The Earth Coated With A Dielectric Layer

Electromagnetic Field of a Horizontal Infinitely Long Wire over the Dielectric-Coated Earth

High-Precision Forward Modeling of Controlled Source Electromagnetic Method Based on Weighted Average Extrapolation Method

An Efficient Modeling Method for Large-Scale Complex Finite-Element Electric Field Numerical Calculation

A Legendre Spectral-Element Method to Incorporate Topography for 2.5D Direct-Current-Resistivity Forward Modeling

Finite Element Simulation of 3-D Marine Controlled Source Electromagnetic Fields in Anisotropic Media with Unstructured Tetrahedral Grids

Three-Dimensional Inversion of Borehole-Surface Resistivity Method Based on the Unstructured Finite Element

Spectral element method for 3-D controlled-source electromagnetic forward modelling using unstructured hexahedral meshes

Strength of the Electric Dipole Source Field in Multilayer Spherical Media

High-order Finite Element Forward Modeling Algorithm for Three-dimensional Borehole-to-surface Electromagnetic Method using Octree Meshes