Abstract:Journal of Thermoplastic Composite Materials, Ahead of Print. This interesting study investigated the effect of Maleic Anhydride-grafted-Polypropylene/Epoxidized Natural Rubber (PP-g-MA/ENR) as a compatibilizing agent (CA) on the properties of a 30/70 Polypropylene/Natural Rubber PP/NR blends. The effect of dynamic vulcanization with sulfur-donors (i.e.: Tetramethyl thiuram disulfide (TMTD) and 4,4 Dithiodimorpholine (DTDM)) which were used as vulcanizing agents was also reported. Several formulations of TPVs with different concentrations of CA (from 5 to 15 phr) were prepared by mixing in the molten state using a Haake Rheocord 90. The structural analysis of dual compatibilizer was examined by FTIR spectroscopy. The rheological behavior was examined using Haake Rheocord 90. The mechanical properties were determined by the tensile measurements. The dynamic mechanical thermal properties were investigated by DMA. A morphological examination was conducted using SEM Microscopy, respectively. FTIR analysis confirmed reactions between the MA group in PP-g-MA and the epoxy groups in ENR, resulting in ENR-grafted PP with an ester and acid-based linkage. The Haake plastograms revealed a proportional increase in the final mixing torque value with the increasing content of CA. The mechanical results exhibited higher values in terms of tensile strength and Young's modulus for the TPVs containing CA compared to un-compatibilized ones. The compatibilized TPV blends exhibited a noteworthy increase in storage modulus and a notable decrease in loss tangent values with the CA concentration increased. Furthermore, the TPVs show two distinct-phase morphologies. That is, the TPV with CA showed the presence of smaller vulcanized rubber particles dispersed within the PP matrix, a phenomenon that becomes more pronounced with higher CA contents.

Compatibilizing Effect of Fluororubber Grafted by Γ-Methacryloxypropyltrimethoxysliane in Fluororubber/Silicone Rubber Blends

Study on the Preparation of Macromolecular Compatibilizer and Its Effect on the Characteristics of Fluoroelastomer (fkm)/silicone Rubber (MVQ) Blend

Effects of reactive compatibilization on the morphological, thermal, mechanical, and rheological properties of intumescent flame-retardant polypropylene.

Enhanced Compatibility and Thermo-Oxidative Stability of Silicone Rubber/Ethylene–Propylene Terpolymer Composites Via in Situ Interface Coupling

Fluorination Modification of Methyl Vinyl Silicone Rubber and Its Compatibilization Effect on Fluorine/Silicone Rubber Composites

The efficacy of methyl vinyl silicone-g-maleic anhydride in the compatibilization of fluoroelastomer and silicone based super specialty elastomer blend

Effect of graphite and its surface modification on thermal conductivity of silicone rubber

Preparation of High-Strength and Excellent Compatibility Fluorine/Silicone Rubber Composites under the Synergistic Effect of Fillers

Silicone rubber/benzoxazine resin‐based nanocomposites: A study on compatibility and thermal stability

Effect of compatibilisers on the cure characteristics and mechanical properties of ternary rubber blend composites

Effect of silane coupling agent grafted glycidyl methacrylate on hollow microsphere/natural rubber composites

The effect of physical compatibilization and dynamic vulcanization on the properties of thermoplastic vulcanizates derived from polypropylene and natural rubber blends

Blends of polydimethylsiloxane-based polyurethane and poly (propylene glycol)-based polyurethane with co-continuous structures: morphology evolution, synergistic effects and application in strain sensors

Rheological and Dynamic Mechanical Behaviors of Short Nylon Fiber and Silica Filled Natural Rubber Compounds

Effects of modified silica on the co‐vulcanization kinetics and mechanical performances of natural rubber/styrene–butadiene rubber blends

Compatibilization of Acrylic Polymer-Silk Fibroin Blend Fibers: 2. Morphology and Mechanical Properties of the Compatilized Blend Fibers

Epoxy Resin Modified Maleic Anhydride‐grafted‐liquid Polybutadiene on the Properties of Short Aramid Fiber Reinforced Natural Rubber Composite

Effect of epoxy functionalized elastomer modified carbon fiber on mechanical properties and interfacial adhesion of chloroprene rubber (CR)/natural rubber (NR) composites

Effect of Compatibilizer on the Transfer and Tribological Behaviors of PA46/HDPE Polyblends

Optimization and Characterization of the F-LSR Manufacturing Process Using Quaternary Ammonium Silanolate as an Initiator for Synthesizing Fluorosilicone

Polymer Blends of Pbt and Pp Compatibilized by Epoxidized Ethylene Propylene Diene Rubber