Abstract:This paper presents detailed numerical analysis of shallow reversed blade-angle slots casing treatment(RSCT) in a transonic axial compressor stage operating at design and off-design conditions. Previous studies have shown that the present compressor rotor is tip-typical and suitable for the use of casing treatment to improve flow stability and enhance stall margin. The unsteady simulations are performed with a three-dimensional time accurate Favre-averaged Navier-stokes flow solver. The numerical results with solid casing demonstrate that the numerical stall is initiated from rotor tip blockage caused by tip clearance vortex(TLV). At both design and off-design conditions, low energy flow zone caused by TLV and the interaction of shock and boundary layer bring about severe passage blockage, the stall characteristics contain of the tip blockage stall and blade tip stall. However, instantaneous flow field visualization analysis shows that the unsteady characteristics of tip blockage at two operating conditions are very different. The RSCT casing treatment improves effectively the stable operating range of the present compressor stage at both design and off-design conditions, the stall margin improvement(SMI) up to 8.7% and 15.6% separately, with the peak efficiency dropped slightly (less than 1.2%). The unsteady suction and injection effect of the RSCT slots removes observably the low energy blockage induced by TLV and weakens the separation of the blade suction surface boundary layer, playing a stabilizing role in the rotor blade tip flow. However, the comparison between SC and RSCT of the radial distribution of absolute rotor outflow angle and stator passages flow show RSCT brings about negative influence to compressor stator. At RSCT near stall condition, the absolute rotor outflow angle increases by about 3 degrees, and stator suction surface vortex shedding causes severe unsteady stator passages blockage, which is likely to trigger the new inception for compressor stall.

Investigation of the Casing Groove Location Effect for a Large Tip Clearance in a Counter-Rotating Axial Flow Compressor

Effect of Circumferential Single Casing Groove Location on the Flow Stability under Tip-Clearance Effect in a Transonic Axial Flow Compressor Rotor

Numerical Investigation for the Impact of Single Groove on the Stall Margin Improvement and the Unsteadiness of Tip Leakage Flow in a Counter-Rotating Axial Flow Compressor

Numerical Analysis of the Effects of Circumferential Groove Casing Suction in a Counter-Rotating Axial FLow Compressor

The impact of casing groove location on the flow instability in a counter-rotating axial flow compressor

Numerical Analysis of the Circumferential Grooves Casing Treatment in a Counter-Rotating Axial Flow Compressor

Investigation of Tip Leakage Flow and Stage Matching with Casing Treatment in A Transonic Mixed-Flow Compressor

Numerical Investigation of the Impacts of Circumferential Single Casing Groove Location on the Overall Performance in a Transonic Fan Rotor

The Impact of Casing Groove Location on Stall Margin and Tip Clearance Flow in a Low-Speed Axial Compressor

Effects Of Tip Clearance Size On The Performance And Tip Leakage Vortex In Dual-Rows Counter-Rotating Compressor

Numerical Investigation of Tip Clearance Size Effect on the Performance and Tip Leakage Flow in A Dual-Stage Counter-Rotating Axial Compressor

Experimental And Numerical Investigation Of Effect Of Center Offset Degree On Compressor Stability With Circumferential Grooved Casing Treatment

Mechanism of the Interaction Between Casing Treatment and Tip Leakage Flow in a Subsonic Axial Compressor

Numerical Investigation of Circumferential Groove Casing Treatment in a Highly-Loaded Low-Reaction Transonic Compressor Rotor

Numerical Investigation of Interaction Between Casing Treatment and Tip Leakage Flow in a Transonic Compressor Rotor

Study of Transient Tip Leakage Vortex Characteristics in a Contra-Rotating Compressor

Combined control of variant clearance and casing aspiration on tip flow field and instability of a transonic compressor

Numerical Study On The Effect Of Slot-Type Casing Treatment In A Transonic Compressor

Effect of Different Tip Clearance Treatments on Performance of an Axial-flow Compressor

Numerical Investigation into the Effects of Casing Aspiration on the Overall Performance and Flow Unsteadiness in a Counter-Rotating Axial Flow Compressor

Analysis of Impact of a Novel Combined Casing Treatment on Flow Characteristics and Performance of a Transonic Compressor