Abstract:As a natural polyphenolic compound, tannin was characterized by high degree of aggregation and high molecular weight which made the adhesive prepared by tannin to have low degree of cross-linking. Many studies reported that the introduction of bridging agents which copolymerized with tannin can improve the polycondensation reaction ability of tannin. Therefore, this study used dimethyl carbonate（DMC）, a kind of chemical raw material with low toxi-city and environmental-friendly performance, to carbonize tannins and then copolymerized it with methylol urea（MMU） to prepare wood adhesives in order to reduce the steric hindrance between the reactive sites of tannins and improve the bonding quality of tannin resins. In this study, the structure of the resin was analyzed by the Fourier transform infrared spectroscopy（FT-IR）; the curing behavior of the resin was tested by the differential scanning calorimetry（DSC）; and the thermal stability of the cured resin product was studied by the thermogravimetric（TG） analysis. At the same time, the physical and chemical properties of the developed resin（solid content, viscosity, and gel time） and the shear strength of the plywood were also tested. The research results showed that the carbonated tannin resin had higher solid content（between 40.0% and 43.0%） and gel time, but lower viscosity compared to the non-carbonated tannin. Through the analysis of FT-IR, it was found that tannins had undergone carbonation reaction due to the action of DMC, which is beneficial to the copolymerization reaction with MMU. However, the amount of MMU was hardly to change the structure of resins. Besides, the curing temperature of carbonated tannin copolymerization series resin showed a trend of firstly rising and then falling, especially, it was showed an increased temperature when MMU was added in the level of 60 g/125 g, which indicated that the resin system had formed a completely cross-linked network. At the same time, in the TG analysis it was also found that the carbonated tannin resin had higher thermal stability than the non-carbonated resin and the level of 60 g/125 g MMU addition was the best in the experiment which formed an effective cross-linking structure. In addition, to investigate the bonding strength of plywood, it was disco-vered that the plywood made by the carbonated tannin copolymer resin exhibited higher shear strength than the non-carbonated resin. The 60 g/125 g MMU addition still had the optimal effect on the resin. However, the carbonated tannin copolymer resin did not contribute much to the reduction of the formaldehyde emission under the same MMU addition level with more formaldehyde amount.

Lignin Impacts on the Lignin-urea-formaldehyde Copolymer Resin and the Reaction Mechanism

Lignin Impacts on the Preparation of Phenolic-resin/Lignin Block Copolymer Resin and the Reaction Mechanism

Synthesis of wood lignin-urea-formaldehyde resin adhesive

Melamine–Urea–Formaldehyde Resin Adhesive Modified with Recycling Lignin: Preparation, Structures and Properties

Effect of Urea on the Properties of Lignin Phenol Formaldehyde Adhesive

Effect of Lignin Structure Characteristics on the Performance of Lignin Based Phenol Formaldehyde Adhesives.

Synthesis of High-Water-Resistance Lignin-Phenol Resin Adhesive with Furfural as a Crosslinking Agent

SYNTHESIS AND CHARACTERIZATION OF LIGNIN-BASED ADHESIVE CROSS-LINKED WITH FURFURYL ALCOHOL–FORMALDEHYDE AND EPOXY RESINS

Unexpected role of amphiphilic lignosulfonate to improve the storage stability of urea formaldehyde resin and its application as adhesives

Synthesis of Lignin-Based Polyacid Catalyst and Its Utilization to Improve Water Resistance of Urea–formaldehyde Resins

Improving the Reactivity of Sugarcane Bagasse Kraft Lignin by a Combination of Fractionation and Phenolation for Phenol-Formaldehyde Adhesive Applications

Blending Mass Ratios of Lignin , Epoxy Resin , and Polyamine Tests

Preparations and Properties of Polyurethane Adhesives Modified by Corn Straw Lignin

Preparation and Application of Formaldehyde-Free Polymer Adhesive

Preparation and Properties of Lignin-Epoxy Resin Composite

PREPARATION OF A LIGNIN-BASED COMPOSITE AND ITS PROPERTIES

Preparation, optimisation and characterisation of lignin phenol formaldehyde resin as wood adhesive

Preparation and Characterization of Urea–formaldehyde Adhesives Modified with Glyoxalated Tannin

Use of lignin in polyurethane-based structural wood adhesives

Characterization on the Copolymerization Resin between Bayberry (Myrica rubra) Tannin and Pre-Polymers of Conventional Urea–Formaldehyde Resin

Preparation of tannin-urea-formaldehyde resin by carbonated tannin and its bonding properties