Abstract:Lithium-sulfur (Li-S) batteries are widely regarded as the next-generation energy storage technology, due to their high potential in energy density and a low projected cost. Practical applications of such batteries are plagued with radical challenges that mainly stem from two factors. First, both sulfur and its final lithiation product, Li2S, are insulating. Thus, the reaction kinetics is slow and often leads to a low attainable capacity. Second, active material dissolve in the electrolyte in the form of lithium polysulfides. This dissolution causes a series of problems, including loss of cathode materials by diffusion away from the cathode, collapse of the cathode structure, and the polysulfide shuttle effect. As a result, Li-S batteries commonly show fast capacity decay and low coulombic efficiency. Herein, we report the exceptional battery performance of porous carbon-sulfur composite microspheres, PSC-S, that benefited from simultaneous control of nanostructure and microscale particle morphology. The porous carbon microspheres (PSC) was synthesized as the sulfur host,by combining emulsion polymerization and evaporation-induced self-assembly (EISA) process, with a good control of both pore structure and microscale particle morphology. Such material not only demonstrated superioty in attainable capacity, but also in several other critical parameters for the development of high-energy Li-S batteries. PSC-S composite boasts a high tap density of 1.08 g/ml and contains 75 wt.% sulfur embedded into the mesopores of its carbon framework. At a high sulfur loading of 5 mg-S/cm2 and 60wt.% sulfur content in the electrode, this material delivers both high gravimetric and high volumetric capacity with excellent retention. Carbon nanotubes (CNTs) can also be readily incorporated into the microspherical structure in the synthesis process to form a porous spherical carbon-carbon nanotube-sulfur composite (PSC-CNT-S). CNT incorporation effectively raises the conductivity of the composite, and thus significantly improves its high-rate performance. At a high current density of 2.8 mA/cm2, an initial capacity of 1100 mAh/g and a reversible capacity of 700 mAh/g after 200 cycles were achieved in PSC-CNT-S. The resultant areal capacity of over 3.5 mAh/cm2 is much higher than in previous reports of Li-S cathodes fabricated using coating techniques.

In Situ Synthesis of Li2S‐Loaded Amphiphilic Porous Carbon and Modification of the Li2S Electrode for Long‐Life Li2S Batteries

Li2S in Situ Grown on Three-Dimensional Porous Carbon Architecture with Electron/Ion Channels and Dual Active Sites As Cathodes of Li-S Batteries

A Freestanding Flexible Single‐Atom Cobalt‐Based Multifunctional Interlayer Toward Reversible and Durable Lithium‐Sulfur Batteries

Li 2 S In Situ Grown on Three-Dimensional Porous Carbon Architecture with Electron/Ion Channels and Dual Active Sites as Cathodes of Li–S Batteries

Facile Synthesis of Porous Li2S@C Composites As Cathode Materials for Lithium–sulfur Batteries

"Wane and wax" strategy: Enhanced evolution kinetics of liquid phase Li2S4 to Li2S via mutually embedded CNT sponge/Ni-porous carbon electrocatalysts

Encapsulating Sulfur into a Gel-Derived Nitrogen-Doped Mesoporous and Microporous Carbon Sponge for High-Performance Lithium-Sulfur Batteries

Synthesis and Electrochemical Performance of Micro-Mesoporous Carbon-Sulfur Composite Cathode for Li–S Batteries

An Efficient Li 2 S-based Lithium-ion Sulfur Battery Realized by a Bifunctional Electrolyte Additive

Freestanding Flexible Li2S Paper Electrode with High Mass and Capacity Loading for High‐Energy Li–S Batteries

Efficient Entrapment and Catalytic Conversion of Lithium Polysulfides on Hollow Metal Oxide Submicro-Spheres As Lithium-Sulfur Battery Cathodes

Tailored Reaction Route by Micropore Confinement for Li–S Batteries Operating under Lean Electrolyte Conditions

High-Rate and Long-Term Cycle Stability of Li-S Batteries Enabled by Li2S/TiO2-Impregnated Hollow Carbon Nanofiber Cathodes.

In Situ Generated Li2S-LPS Composite for All-Solid-state Lithium-Sulfur Battery

Long-life Li–S batteries based on enabling the immobilization and catalytic conversion of polysulfides

Stabilizing high sulfur loading Li–S batteries by chemisorption of polysulfide on three-dimensional current collector

Electronic Structure Adjustment of Lithium Sulfide by a Single-Atom Copper Catalyst Toward High-Rate Lithium-Sulfur Batteries

Enabling High Energy Density Cathode for Lithium-Sulfur Batteries.

Construction of SnS2-modified multi-hole carbon nanofibers with sulfur encapsulated as free-standing cathode electrode for lithium sulfur battery

Mesoporous Carbon-Sulfur Composite Microspheres with Multiscale Morphology Control to Achieve High Areal Capacity for Lithium-Sulfur Battery Cathodes

Hollow carbon spheres with nanoporous shells and tailored chemical interfaces as sulfur host for long cycle life of lithium sulfur batteries