Abstract:Purpose The purpose of this study was to compare the effect of varying screw lengths on load to failure and retention of the dorsal ulnar corner fragment after fixation of comminuted intra-articular distal radius fractures in a cadaveric model. Methods Twenty-four fresh frozen cadaveric forearms were subjected to a standardized distal radius osteotomy to mimic an intra-articular fracture pattern. Dual X-ray absorptiometry scans were performed to ensure minimal variability in bone density. All fractures were fixed with a volar locking plate and distal locking screws. Three different lengths of distal locking screws were used in each group of eight specimens to simulate the clinical decision of different distal screw lengths. The screw lengths tested were bicortical, 100% of the width of the bone but unicortical, and 75% of the width of the bone and unicortical. All specimens were preconditioned with cyclic axial loading and then axially loaded using matching acrylic resin molds to clinical failure and fragment displacement as detected by a motion analysis system. Retention or loss of the dorsal ulnar corner fragment during loading was recorded as a binary variable. Results Between the three groups, there were no statistically significant differences in precycling stiffness, postcycling stiffness, load at 2 mm displacement of the dorsal ulnar corner, or force at failure. The group with 75% length screws had a significantly higher loss of reduction of the dorsal ulnar corner (86%) compared with the other groups (0%). Conclusions Varying screw lengths did not affect the stiffness or overall loads to failure of axially loaded specimens. However, the 75% length screws did not reliably secure the dorsal ulnar corner fragments. Although this did not significantly affect the overall load to failure of the construct, displacement of this fragment may have implications for rotation of the forearm through the distal radioulnar joint. Clinical relevance Surgeons should consider the utilization of full-length unicortical locking screws to ensure adequate fixation of the dorsal ulnar corner. Type of study/level of evidence Biomechanical study V.

Three fixation options for treatment of intra-articular fractures of the distal radius: an ex vivo biomechanical study

[Study on biomechanical stability in simulated femoral neck fracture fixation by two cannulated screws].

Biomechanical evaluation of different fixation methods for fracture dislocation involving the proximal tibia

Comparison of the Therapeutic Effects of Two Kinds of Internal Fixation for Distal Radial Fractures

Osteosynthesis of Phalangeal Fractures: Biomechanical Comparison of Kirschner Wires, Plates, and Compression Screws

[Biomechanical Research of Antegrade Intramedullary Fixation for the Metacarpal Fractures].

Effect of prostaglandins on the development of rabbit embryos.

Effect of Screw Length in Volar Plating for Intra-articular Distal Radius Fractures: A Biomechanical Study

Locking Compression Plate Combined with Kirschner Wire Fixation for Treatment of High-Energy Type C Distal Radius Fractures in Young Patients

Biomechanical comparison of different internal fixation devices for transversely unstable Mason type II radial head fractures

Biomechanical comparison of intramedullary nail and plate osteosynthesis for extra-articular proximal tibial fractures with segmental bone defect

Comprehensive biomechanical analysis of three clinically used fixation constructs for posterior malleolar fractures using cadaveric and finite element analysis

Giant leap for p53, small step for drug design.

Biomechanical evaluation of novel intra- and extramedullary assembly fixation for proximal humerus fractures in the elderly

Cadaveric biomechanical assessment of different configurations for a novel pin and plate fixation method in distal humerus fractures

Arthroscopic and locking plate treatment in comminuted fractures of distal radius

Radiographic Analysis in Extra-Articular and Intra-Articular Distal Radius Fractures Treated with Variable-Angle Volar Locking Plate Fixation

Biomechanical comparison of three fixation strategies for radial head fractures: a biomechanical study

Finite Element Analysis of Three Internal Fixations for the Posteromedial Split Fracture Fragment in Tibial Plateau Fractures

Biomechanical comparison of dorsal versus volar plate osteosynthesis for the dorsally unstable distal radius fracture

A novel configuration for the fixation of intra-articular C2.3 distal humerus fractures with the potential for minimally invasive surgery: A biomechanical evaluation and finite element analysis