Abstract:Purpose: To quantify the sensitivity of Dose Length Product to Effective Dose conversion factors (k‐factors) to scan length and position. Methods: To convert the recorded Dose Length Product (DLP) to an estimate of Effective Dose (E), a set of conversion factors, known as k‐factors, are used. These published k‐factors were developed for a limited set of standard protocols with fixed scan lengths, and most are based on stylized models of the human body. Using realistic models of male and female (RPI‐AM and RPI‐AF) and a validated model of the CT source, Monte Carlo simulations are preformed to calculate the dose to each organ on a slice‐by‐slice basis. For each slice, the organ doses are converted into ‘local' k‐factors. Over a full scan length, the effective doses from the individual slices and the DLPs are summed, so the k‐factor for the scan is equivalent to the average of the local k‐factors in the scan range. Results: Simulations of 1‐cm thick CT slices were performed over the entire range of the torso for the RPI‐AM and RPI‐AF phantoms. The local k‐factors calculated range from a minimum of 0.0128 in the upper shoulder region (above most of the radio‐sensitive organs of the chest), to a maximum of 0.0369 in the region around the female gonads. The calculated k‐factor for a standard chest scan was 0.0289, which compares favorably to published values. However, the k‐factor decreases as the scan range is expanded. Consequently, a chest scan that is only 10 cm longer would have a k‐factor 18% lower when compared to the standard protocol. Conclusion: By improving the understanding of the sensitivity of k‐factors to scan length and position, more accurate estimates of effective dose from CT examination can be provided without sacrificing the efficiency and simplicity that k‐factors provide. This project was funded by National Institutes of Health (National Institute of Biomédical Imaging and Bioengineering R42EB010404).

Eatimation of effective doses from a dental cone beam computed tomographic scanner

A review of dental cone-beam CT dose conversion coefficients

Dose measurements for dental cone-beam CT: a comparison with MSCT and panoramic imaging

Effective radiation dose of ProMax 3D cone-beam computerized tomography scanner with different dental protocols.

Effective radiation dose and eye lens dose in dental cone beam CT: effect of field of view and angle of rotation

Absorbed Dose Model to Scan Parameters in Dental Cone Beam Computed Tomography

Converting dose-area product to effective dose in dental cone-beam computed tomography using organ-specific deep learning

[Comparative Dosimetry of Dental Cone-Beam Computed Tomography and Multi-Slice Computed Tomography for Oral and Maxillofacial Radiology].

Reactivation of ophthalmic herpes zoster following pulsed‐dye laser treatment for inflammatory acne vulgaris

Organ and Effective Dose Evaluation in Coronary Angiography by Using a 320 MDCT Based on In-Phantom Dose Measurements with TLDs

Estimating organ dose with optimized peak dose index in cone-beam CT scans

SU‐C‐217A‐03: Position Sensitivity of Calculated Dose‐Length‐Product‐To‐Effective‐ Dose Conversion Factors in Computed Tomography Examination

Dental and Maxillofacial Cone Beam Computed Tomography Absorbed Dose Distribution Calculation by GEANT4

Image quality-based dose optimization in pediatric cone-beam computed tomography: A pilot methodological study

Dose-Area-Product (Dap) Modelling Of Siemens Max-Series X-Ray Digital Radiography (Dr) Systems

[The Study for Standardization of Dose Evaluation Method in Cone-beam CT]

Evaluation of Radiation Exposure and Influential Factors in Cone-Beam Computed Tomography (CBCT) of the Head and Abdomen during Interventional Procedures

Radiation dose in non-dental cone beam CT applications: a systematic review

Dose length product to effective dose coefficients in adults

MDL 27,531 reduces spontaneous hindlimb contractions in rats with chronic transections of the spinal cord

Preliminary Investigation of Dose Allocation in Low-Dose Cone-Beam CT