Abstract:Abstract Thermoelectric (TE) materials have drawn a lot of attention as a promising technology to harvest waste heat and convert it into electrical energy. However, the toxicity and expense of inorganic TE materials along with high-temperature fabrication processes have limited their application. Additionally, the reduction of raw material resources, such as metals and petroleum is another limiting factor. Hence, developing low-cost, stable, and easily-created TE materials from renewable resources is attracting more and more interest for a wide range of applications including the internet of things and self-powered sensors. Herein, an efficacious processing strategy to fabricate printable TE materials has been developed with Ethyl cellulose (EC), a non-conducting polymer, as the polymer matrix and with Graphene nanoplatelets (GNPs) as fillers. EC, one of the cellulose’s derivatives, has been widely used as a binder in the printing pastes. The conductive pastes with different filler contents have been fabricated. The weight ratio of GNPs and EC were ranged from 0.2 to 0.7. These conductive pastes have been deposited by blade coating on glass substrates. The electrical conductivity of the composites has increased polynomially as the filler content increased, whereas the Seebeck coefficient did not change significantly with the increased electrical conductivity. The highest electrical conductivity at room temperature (355.4 S m −1 ) was obtained for the ratio of 0.7. This ratio also had the maximum power factor value. Moreover, a 3D structure form (cylindrical pellet) from the highest conductive paste was also fabricated. The proposed technique demonstrates an industrially feasible approach to fabricate different geometries and structures for organic TE modules. So, this approach could provide a good reference for the production of high efficiency, low-temperature, lightweight, low-cost, TE materials.

Ionic Thermoelectric Paper [erratum: Sept. 2017, V.5(37), P.20053]

Selectively Tuning Ionic Thermopower in All-Solid-state Flexible Polymer Composites for Thermal Sensing

Tailoring P-N Conversion in All-solid-state Polymer Composites with A Record Ionic Thermopower

Ultra-high Performance of Ionic Thermoelectric-Electrochemical Gel Cells for Harvesting Low Grade Heat

Cellulose‐Based Radiative Cooling and Solar Heating Powers Ionic Thermoelectrics

Flexible hydrogel with a coupling enhanced thermoelectric effect for low-grade heat harvest

Thermoelectric Properties of Flexible PEDOT:PSS/Polypyrrole/Paper Nanocomposite Films

Stretchable Polyvinyl Alcohol and Sodium Alginate Double Network Ionic Hydrogels for Low-Grade Heat Harvesting with Ultrahigh Thermopower

Ionic Thermoelectric Materials: Innovations and Challenges

Facile fabrication of paper-based flexible thermoelectric generator

Cellulose ionic conductors with high differential thermal voltage for low-grade heat harvesting

Ultrasensitive Flexible Thermal Sensor Arrays based on High‐Thermopower Ionic Thermoelectric Hydrogel

Effects of Cationic Size on Thermoelectricity of PEDOT:PSS/Ionic Liquids Hybrid Films for Wearable Thermoelectric Generator Application

Wearable Device with High Thermoelectric Performance and Long‐Lasting Usability Based on Gel‐Thermocells for Body Heat Harvesting

Bi0.5Sb1.5Te3/PEDOT:PSS-based flexible thermoelectric film and device

Duplication of the Entire Small Intestine with Massive Melena

Developing printable thermoelectric materials based on graphene nanoplatelet/ethyl cellulose nanocomposites

Self-Standing and Flexible Thermoelectric Nanofiber Mat of an n-Type Conjugated Polymer

Hierarchically Anisotropic Networks to Decouple Mechanical and Ionic Properties for High-Performance Quasi-Solid Thermocells

Flexible Quasi‐Solid State Ionogels with Remarkable Seebeck Coefficient and High Thermoelectric Properties

Flexible Thermoelectric Composite Films of Polypyrrole Nanotubes Coated Paper