Abstract:The 3rd generation aluminium‐lithium (Al-Li) alloy demonstrates promising potential in various applications due to its advanced synergy of strength, toughness, corrosion resistance and weight reduction. However, like its predecessors, this alloy also suffers from the anisotropy issue which can exert significant impact on the manufacturing processes. This study seeks to investigate the anisotropy evolution of a T8 temper 3rd generation Al-Li alloy when subjecting to increased tensile pre-deformation at 0°, 45°, and 90° to the rolling direction. Uniaxial creep-ageing and tensile tests were conducted to reveal the anisotropic behaviours of the material during creep and tensile deformation. Electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM) methods were used to investigate the microstructural evolutions and their influence on the material anisotropy evolvement with treatments of tensile pre-deformation and creep-ageing. It was found that with the increase of tensile pre-deformation level, the creep deformation increased at 0° while decreased at 45° and 90°, due to different configurations of the dislocation substructures at 0°, 45° and 90°. Furthermore, the in-plane anisotropy (IPA) was reduced in both the creep deformation and material strength with increasing tensile pre-deformation and subsequent creep-ageing. The enhanced creep deformation at 0° and decreased deformation at 45° and 90°, as well as the reduction of anisotropy, can be attributed to the reconfiguration of dislocation structures and different extents of precipitation promotion at different directions when subjected to tensile pre-deformation and creep-ageing.

A Review of the Effect of Prior Inelastic Deformation on High Temperature Mechanical Response of Engineering Alloys

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Evaluation of the Effect of Various Prior Creep-Fatigue Interaction Damages on Subsequent Tensile and Creep Properties of 9%cr Steel

Influence of Prior Low Cycle Fatigue on Microstructure Evolution and Subsequent Creep Behavior

Effect of pre-straining treatment on high temperature creep behavior of Ni-based single crystal superalloys

The Effect of Strain Rate on the Tensile Deformation Behavior of Single Crystal, Ni-Based Superalloys

Enhancement of Creep Lifetime of Aluminum through Severe Plastic Deformation

The Effect of Pre-Deformation on the Microstructure Evolution of NiAl Model Single Crystal Superalloy During Thermal Exposure at 1000 °C

Strain Rate Effects on the Mechanical Properties of an AlCoCrFeNi High-Entropy Alloy

Effect of nanoparticles on creep behaviour of metals: A review

Quantification of the effect of increased pre‐deformation on microstructure and mechanical properties of 2A55 Al‐Li Alloy

Effect of Strain Rate and Temperature on Dynamic Mechanical Behavior and Microstructure Evolution of Ultra-High Strength Aluminum Alloy

Investigation of anisotropy evolution of an aluminium‐lithium alloy with increasing pre-deformation in creep age forming

Influence of temperature on creep behavior, mechanical properties and microstructural evolution of an Al-Cu-Li alloy during creep age forming

Experiment and Modelling of the Pre-Strain Effect on the Creep Behaviour of P/M Ni-Based Superalloy FGH96

The Effect of Deformation and Isothermal Heat Treatment of a 5005 Aluminum Alloy

Effect of Deformed Prior Austenite Characteristics on Reverse Phase Transformation and Deformation Behavior of High-Strength Medium-Mn Steel

Environmental Effects on the Creep Response of Thin-Walled Ni-Based Single Crystal Superalloys

Effects of pre-deformation on microstructure, mechanical properties and corrosion performance of an Al-Cu-Mg-Ag alloys

Effect of High-Temperature Severe Plastic Deformation on Microstructure and Mechanical Properties of IF Steel

Recent Development of Superplasticity in Aluminum Alloys: A Review