Abstract:Due to the increasing demands for lightweight parts in various fields, such as bicycle, automotive, aircraft and aerospace industries, hydroforming processes have become popular in recent years. Since tubular materials during tube hydroforming are under a bi-axial even tri-axial stress state, which is different from that in the tensile test, it is necessary to test the mechanical properties of the material under bi-axial stress state. Tube bulging test is an advanced method for characterizing the mechanical properties of tubular materials under bi-axial stress state. But there are excessive physical quantities in the theoretical model of tube bulging test for testing the mechanical properties of tubes under bi-axial stress state which are difficult to be obtained during the experiment. In order to solve the problems, a method for directly testing the mechanical properties of tubes under bi-axial stress state was proposed in this work, which will be referred to as "one point method". Because of circular model is characterized by a dominant function expression, theoretical models of both the pole axial curvature radius and the pole thickness during bulging test are derived under supposing the geometrical models for bulging zone as circular. Thus, the mechanical properties of tubes under bi-axial stress state can be obtained only through measuring the bulging height at the pole point during the bulging test, which laid the foundation for the establishment of a simple and reliable method for testing the mechanical properties of the tube online. Based on the above proposed method, the extruded aluminum alloy tubes AA6061 were tested. The results showed that both the pole axial curvature radius and the pole thickness during bulging test can be expressed as display functions pertaining to the bulging height at the pole point. For the theoretical model of the pole axial curvature radius, as the bulging rate increases, the prediction accuracy increases at beginning, and decreases at the end when using circular as the theoretical geometrical models for bulging zone. The prediction accuracy is the highest as the bulging rate is about 13%, the prediction accuracy decreases after the bulging rate is more than 20%. Fortunately, the overall prediction error is small. The maximum error does not exceed +/-0.9%. The prediction accuracy of the pole thickness using the theoretical model is almost unaffected by the specimen geometry. When the ratios of length to diameter and diameter to thickness change, the difference is very small, the prediction error is not more than 0.8%. This is very helpful to ensure the accuracy of mechanical testing under bi-axial loading conditions. Using the "one point method", the stress and strain components along the circumferential and axial directions can be simultaneously measured, this laid the foundation for further analysis of the anisotropic property impacting on the flow and subsequent yield under complex stress state.

Analytical Model for Tube Hydro-Bulging Tests, Part II: Linear Model for Pole Thickness and Its Application

Analytical Model for Tube Hydro-Bulging Test, Part I: Models for Stress Components and Bulging Zone Profile

A New Method for Directly Testing the Mechanical Properties of Anisotropic Materials in Bi-Axial Stress State by Tube Bulging Test

Analysis and Finite Element Simulation of the Tube Bulge Hydroforming Process

Deformation Patterns in Hydroforming of Thin-Walled Y-Shaped Tube

Complex Stress-Strain Relations of Tubular Materials Studied with A Flexible Hydroforming System

Characterization of Multiaxial Stress-Strain Response of Tube Metal from Double-Sided Hydro-Bulging Test Based on Hosford’s 1979 Yield Criterion

Identification of Anisotropic Coefficients in the Non-Principal Axis Directions of Tubular Materials Using Hole Bulging Test

Further Assessment of the Plastic Instability of Thin-Walled Tubes in Double-Sided Hydro-Bulging Process with Verification Experiments

Analytical Model for Tube Hydro-Forging: Prediction of Die Closing Force, Wall Thickness and Contact Stress

Effect of Strain State on the Surface Roughening for Hydroforming of Aluminum Alloy Tube Based on Cross-Scale Numerical Modeling

A Study on Numerical Simulation of Hydroforming of Aluminum Alloy Tube

Study on Formability of Tube Hydroforming Through Elliptical Die Inserts

Mechanical Modeling of Tube Bending Considering Elastoplastic Evolution of Tube Cross-Section

The Development of a Continuous Constitutive Model for Thin-Shell Components with A Sharp Change in the Property at Welded Joints

Analysis of Wall Thickness Variation in the Hydro-Bending of a Double-Layered Tube

Analysis of Warping Failure in Tube Hydro-Forging

Axial Stress Analysis for the Hydro Bending Process of Double-Layered Tube

Experimental Verification of the Influence of Normal Stress on the Formability of Thin-Walled 5a02 Aluminum Alloy Tubes

Hardening behavior of 5A02 aluminum alloy tube under combined action of internal and external pressures

Plastic deformation of 2024 aluminum alloy friction stir welded tube during hydro bulging