Kinematic calibration of the 3 degree of freedom redundantly actuated spatial parallel module of a five axis hybrid machine:

Xuan Luo,Fugui Xie,Xin-Jun Liu

DOI: https://doi.org/10.1177/0954405420911299

2020-01-01

Abstract:As a new type of manufacturing equipment, redundant hybrid machines have the theoretical advantage over the traditional serial machines in efficiently processing large structural parts with high ma...

What problem does this paper attempt to address?

A United Kinematic Calibration Method for a Dual-Machine System

Dan Zhao,Yunbo Bi,Yinglin Ke

DOI: https://doi.org/10.1108/aa-02-2017-029

IF: 2.373

2017-01-01

Assembly Automation

Abstract:Purpose This paper aims to propose a united kinematic calibration method for a dual-machine system in automatic drilling and riveting. The method takes both absolute and relative pose accuracy into account, which will largely influence the machining accuracy of the dual-machine system and assembly quality. Design/methodology/approach A comprehensive kinematic model of the dual-machine system is established by the superposition of sub-models with pose constraints, which involves base frame parameters, kinematic parameters and tool frame parameters. Based on the kinematic model and the actual pose error data measured by a laser tracker, the parameters of coordinated machines are identified by the Levenberg–Marquardt method as a multi-objective nonlinear optimization problem. The identified parameters of the coordinated machines will be used in the control system. Findings A new calibration method for the dual-machine system is developed, including a comprehensive kinematic model and an efficient parameter identification method. The experiment results show that with the proposed method, the pose accuracy of the dual-machine system was remarkably improved, especially the relative position and orientation errors. Practical implications This method has been used in an aircraft assembly project. The calibrated dual-machine system shows a good performance on system coordination and machining accuracy. Originality/value This paper proposes a new method with high accuracy and efficiency for the dual-machine system calibration. The research can be extended to multi-machine and multi-robot fields to improve the system precision.
Kinematic Modeling and Base Frame Calibration of a Dual-Machine-based Drilling and Riveting System for Aircraft Panel Assembly

Dan Zhao,Yunbo Bi,Yinglin Ke

DOI: https://doi.org/10.1007/s00170-017-0982-x

IF: 3.563

2017-01-01

The International Journal of Advanced Manufacturing Technology

Abstract:The paper introduces a new automatic drilling and riveting system for aircraft panel assembly which is composed of two five-axis machines in coordination. Kinematic modeling and base frame calibration are fundamental problems for the dual-machine system to improve its positioning accuracy. In this paper, a comprehensive kinematic model for the dual-machine system is established based on the modularization concept, and a new base frame calibration method is proposed which consists of the direct calibration based on laser tracker and calibration error compensation based on a specially designed instrument. In the kinematic modeling stage, the kinematic model of the dual-machine system is divided into three parts and three corresponding sub-models are established. With the pose constraints of coordinated machines, a comprehensive kinematic model of the dual-machine system is built. In the base frame calibration stage, the base frames of dual machines are firstly established by laser tracker. Due to many error sources in the calibration process, the relative pose errors of dual machines exist with the relationship between the base frames of coordinated machines. Then, the calibration error is measured by a specially designed instrument and used to modify the primary base frame calibration results. To verify the validity of the proposed method, experiments have been performed and the results have shown great improvement in base frame calibration accuracy. With the advantage of easy operation and high accuracy, this method can be extended to other multi-machine and multi-robot systems.
Kinematic Calibration Of The 3-Dof Parallel Module Of A 5-Axis Hybrid Milling Machine

Li-Ping Wang,Fu-Gui Xie,Xin-Jun Liu,Jinsong Wang

DOI: https://doi.org/10.1017/S0263574710000433

IF: 2.7

2011-01-01

Robotica

Abstract:This paper investigates the kinematic calibration of a 3-DOF parallel mechanism based on the minimal linear combinations of error parameters. The error mapping function between the geometric errors and the output errors is formulated and the identification matrix is generated and simplified. In order to identify the combinations of error parameters, four theorems to analyze the columns of the simplified identification matrix are introduced. Then, an anti-disturbance index is presented to evaluate the identification performance. On the basis of this index, measurement strategy is developed and optimal measuring configurations are given. After external calibration, linear interpolation compensation is applied to improve the terminal accuracy further. Results of experiment show that the method used in this paper is effective and efficient, and the errors are convergent within two iterations generally. This method can be extended to other parallel mechanisms with weakly nonlinear kinematics.
A Hybrid Analytical and Data-driven Modeling Approach for Calibration of Heavy-duty Cartesian Robot

Hongyu Wan,Silu Chen,Yisha Liu,Chaochao Jin,Furu Chen,Jin Wang,Chi Zhang,Guilin Yang

DOI: https://doi.org/10.1109/AIM43001.2020.9158827

2020-01-01

Abstract:Robot calibration is to enhance absolute positioning accuracy within robotic task space. Traditional method is to build the geometric error model and identify the deviation of kinematic parameters. In this paper, a hybrid analytical and data-driven non-geometric error modeling approach is proposed after the geometric error is compensated. It is intended to satisfy higher accuracy requirements when the heavy-duty Cartesian robot performs metal finishing tasks under different load conditions. Analytical and deterministic Beam Deformation model is built firstly to remove a large portion of the non-geometric error. By this means, data-driven Gaussian Process Regression model can achieve better prediction results due to the collected residual error data is closer to Gaussian distribution. The experimental result of platform tests demonstrates the effectiveness and robustness of the proposed method.
Kinematic Calibration of Gantry Hybrid Machine Tool Based on Estimation Error and Local Measurement Information

Xiaoqiang Tang,Jinsong Wang,Men Gao

DOI: https://doi.org/10.1007/s00170-003-1999-x

IF: 3.563

2004-01-01

The International Journal of Advanced Manufacturing Technology

Abstract:This paper presents the kinematic calibration of a four degrees-of-freedom (DOF) hybrid machine tool based on a novel planar 3-DOFs parallel mechanism and a long movement of the worktable. Closed-form solutions are developed for both the inverse and direct kinematics about the parallel mechanism. The error model is built and the mechanism accuracy is investigated. Two types of kinematic calibration method are proposed by a simple measurement device. The first type of calibration method is based on estimation error, and can easy improve the machine tool accuracy quickly by estimating the error trends. The second type of kinematic calibration method is based on local measurement information, which includes the position errors and does not include the pose errors of the machine tool. The calibration tests showed the effectiveness of the calibration methods, which can be useful for the similar types of parallel machine tool.
Kinematical calibration of a hybrid machine tool with Regularization method

Peng Huang,Jinsong Wang,Liping Wang,Rui Yao

DOI: https://doi.org/10.1016/j.ijmachtools.2010.11.009

IF: 10.331

2011-01-01

International Journal of Machine Tools and Manufacture

Abstract:The hybrid machine tools, combining the advantages of serial and parallel type machine tools, provide more and more application opportunities for less-freedom parallel mechanism. Accuracy performance is still an important index of hybrid machine tool for industry application. In this study, configuration of a 3-P(4R)S-XY hybrid machine tool is first introduced. The 3-P(4R)S parallel mechanism can be simplified to a 3-PRS mechanism on kinematical calibration. Based on that, error model and error kinematics are derived to introduce all possible manufacturing and assembling errors into calibration. Then, identification matrix is derived by differentiating kinematical equations. Combining the advantages of calibration schemes based on both inverse and forward kinematics model, a new measurement scheme is put forward, in which not all freedoms of motions needs to be measured and error identification could be efficiently accomplished in one time measurement. In order to solve the ill-posed problem in error identification, practical Regularization methods are adopted. Finally, the kinematical calibration experiment of the prototype machine tool is performed with a combined measuring tool. The results of RTCP accuracy test reveal that the positioning accuracy is less than 0.05mm in the 30° cone workspace. Calibration experiments for the prototype verify feasibility and effectivity of the more precise kinematical error model, the low-cost measurement scheme, and the error identification solution with Regularization method.
Optimization of a redundantly actuated parallel kinematic mechanism for a 5-degree-of-freedom hybrid machine tool

Fugui Xie,Xin-Jun Liu,Yanhua Zhou

DOI: https://doi.org/10.1177/0954405414522450

2014-03-20

Abstract:In this article, a novel redundant 3-degree-of-freedom parallel kinematic mechanism with high rotational capability is proposed and alternate configurations are presented. Taking the motion/force transmissibility into consideration, a local minimized transmission index is introduced and suggested to act as the performance evaluation criterion for this redundantly actuated parallel kinematic mechanism. On this basis, the optimum design of the proposed parallel kinematic mechanism is carried out and its rotational capability is investigated. The result indicates that the rotational capability of the proposed mechanism can surpass 115°. Compared with traditional parallel kinematic mechanisms, this represents a substantial advantage for practical applications. Using the redundant parallel kinematic mechanism as the parallel module, a redundant hybrid machine tool capable of five-face machining in one setup is developed and applied in the manufacture of parts with freeform surfaces.
Kinematic Calibration Method with High Measurement Efficiency and Robust Identification for Hybrid Machine Tools

Liping Wang,Mengyu Li,Guang Yu,Weitao Li,Xiangyu Kong

DOI: https://doi.org/10.1016/j.cja.2023.08.013

IF: 5.7

2024-01-01

Chinese Journal of Aeronautics

Abstract:Geometric error is the main factor affecting the machining accuracy of hybrid machine tools. Kinematic calibration is an effective way to improve the geometric accuracy of hybrid machine tools. The necessity to measure both position and orientation at each pose, as well as the instability of identification in case of incomplete measurements, severely affects the application of traditional calibration methods. In this study, a kinematic calibration method with high measurement efficiency and robust identification is proposed to improve the kinematic accuracy of a five-axis hybrid machine tool. First, the configuration is introduced, and an error model is derived. Further, by investigating the mechanism error characteristics, a measurement scheme that only requires tool centre point position error measurement and one alignment operation is proposed. Subsequently, by analysing the effects of unmeasured degrees of freedom (DOFs) on other DOFs, an improved nonlinear least squares method based on virtual measurement values is proposed to achieve stable parameter identification in case of incomplete measurement, without introducing additional parameters. Finally, the proposed calibration method is verified through simulations and experiments. The proposed method can efficiently accomplish the kinematic calibration of the hybrid machine tool. The accuracy of the hybrid machine tool is significantly improved after calibration, satisfying actual aerospace machining requirements.
Kinematic Calibration of a Hybrid Machine Tool with Constrained Least Square Method

Mengyu Li,Liping Wang,Guang Yu

DOI: https://doi.org/10.1007/978-981-19-9398-5_85

2023-01-01

Lecture Notes in Mechanical Engineering

Abstract:Kinematic calibration is an effective way to improve the kinematic accuracy of hybrid machine tools. Conventional calibration methods require position and attitude measurements for each measurement pose, and the measurement process, especially the attitude measurement, is extremely complicated. In this paper, a calibration method that only requires position measurement and alignment is proposed. Measurement process can be done using only three dial indicators. Based on this measurement method, a constrained least squares identification method based on the regularization solution is proposed to solve the ill-posed problem. The proposed calibration method is verified by simulation and experiment. The proposed method can complete the calibration with a small measurement cost, which greatly improves the calibration efficiency.
Measurement Trajectory Evaluation and Error Compensation for Kinematic Calibration of a 5-Axis Hybrid Machine Tool

Yuzhe LIU,Jun WU,Liping WANG,Jinsong WANG

DOI: https://doi.org/10.16511/j.cnki.qhdxxb.2016.22.037

2016-01-01

Abstract:This paper described the kinematic calibration of the measurement trajectory and error compensation of a 5-axis hybrid machine tool.The kinematics model was based oh the closed loop vector kinematic equations while the error model was based on the linear perturbation method.An index to evaluate the measurement trajectory was developed from a non-orthogonal index of the trajectory vectors.Two calibration tests were performed using different trajectories.Two error compensation schemes were based on the forward and inverse kinematics.The calibration tests show that the error compensation scheme based on the inverse kinematics has higher compensation accuracy.Finally,a test of machining an "S"-shape test specimen shows that 94％ of the detected points are acceptable.The results verify the effectiveness of the index and the error compensation scheme.
The Calibration Simulation of a Five-axis Parallel Machine Tool

Bin-bin PENG,Feng GAO,Bing WANG,Yi YUE

DOI: https://doi.org/10.3969/j.issn.1001-2265.2005.10.005

2005-01-01

Abstract:After establishing the model for the calibration of a novel five-axis parallel machine tool,the process of calibration is simulated by minimizing inverse kinematic residuals.The results indicate that the kinematic identification algorithm is very efficient and robust.Since the orientation parameters of the reference frame for the parallel machine tool are included in the model of calibration,the model can eliminate the unfavourable influence of the system error created during the measurement and the accuracy of calibration can be improved further.All the results provide the fundamental reference for the trial of calibration of the parallel machine tool.
Accuracy Analysis and Calibration of Gantry Hybrid Machine Tool

唐晓强,李铁民,尹文生,汪劲松

2012-01-01

Tsinghua Science & Technology

Abstract:The kinematic accuracy is a key factor in the design of parallel or hybrid machine tools. This analysis improved the accuracy of a 4-DOF (degree of freedom) gantry hybrid machine tool based on a 3-DOF planar parallel manipulator by compensating for various positioning errors. The machine tool architecture was described with the inverse kinematic solution. The control parameter error model was used to analyze the accuracy of the 3-DOF planar parallel manipulator and to develop a kinematic calibration method. The experimental results prove that the calibration method reduces the cutter nose errors from ±0.50 mm to ±0.03 mm for a horizontal movement of 600 mm by compensating for errors in the slider home position, the guide way distance and the extensible strut home position. The calibration method will be useful for similar types of parallel kinematic machines.
Complete Kinematic Calibration of a 6-RRRPRR Parallel Kinematic Machine Based on the Optimal Measurement Configurations

Chunyang Han,Yang Yu,Zhenbang Xu,Xiaoming Wang,Peng Yu,Xiaoqin Zhou

DOI: https://doi.org/10.1177/0954406219869985

2019-01-01

Abstract:This paper presents a kinematic calibration of a 6-RRRPRR parallel kinematic mechanism with offset RR-joints that would be applied in space positioning field. In order to ensure highly accurate and highly effective calibration process, the complete error model, which contains offset universal joint errors, is established by differentiating inverse kinematic model. A calibration simulation comparison with non-complete error model shows that offset universal joint errors are crucial to improve the calibration accuracy. Using the error model, an optimal calibration configuration selection algorithm is developed to determine the least number of measurement configurations as well as the optimal selection of these configurations from the feasible configuration set. To verify the effectiveness of kinematic calibration, a simulation and experiment were performed. The results show that the developed approach can effectively improve accuracy of a parallel kinematic mechanism with relatively low number of calibration configurations.
A Kinematic Calibration Method of a 3T1R 4-Degree-of-freedom Symmetrical Parallel Manipulator

Fengxuan Zhang,Silu Chen,Yongyi He,Guoyun Ye,Chi Zhang,Guilin Yang

DOI: https://doi.org/10.3390/sym12030357

2020-01-01

Symmetry

Abstract:This paper proposes a method for kinematic calibration of a 3T1R, 4-degree-of-freedom symmetrical parallel manipulator driven by two pairs of linear actuators. The kinematic model of the individual branched chain is established by using the local product of exponentials formula. Based on this model, the model of the end effector’s pose error is established from a pair of symmetrical branched chains, and a recursive least square method is applied for the parameter identification. By installing built-in sensors at the passive joints, a calibration method for a serial manipulator is eventually extended to this parallel manipulator. Specifically, the sensor installed at the second revolute joint of each branched chain is saved, replaced by numerical calculation according to kinematic constraints. The simulation results validate the effectiveness of the proposed kinematic error modeling and identification methods. The procedure for pre-processing compensation on this 3T1R parallel manipulator is eventually given to improve its absolute positioning accuracy, using the inverse of the calibrated kinematic model.
Kinematic Calibration of a 3-DOF Parallel Tool Head.

Yuzhe Liu,Jun Wu,Liping Wang,Jinsong Wang,Dong Wang,Guang Yu

DOI: https://doi.org/10.1108/ir-07-2016-0184

2017-01-01

Industrial Robot the international journal of robotics research and application

Abstract:Purpose The purpose of this study is to develop a modified parameter identification method and a novel measurement method to calibrate a 3 degrees-of-freedom (3-DOF) parallel tool head. This parallel tool head is a parallel mechanism module in a five-axes hybrid machine tool. The proposed parameter identification method is named as the Modified Singular Value Decomposition (MSVD) method. It aims to overcome the difficulty of choosing the algorithm parameter in the regularization identification method. The novel measurement method is named as the vector projection (VP) method which is developed to expand the measurement range of self-made measurement implements. Design/methodology/approach Newton Iterative Algorithm based on Least Square Method is analyzed by using the Singular Value Decomposition method. Based on the analysis result, the MSVD method is proposed. The VP method transforms the angle measurement into the displacement measurement by taking full advantage of the ability that the 3-DOF parallel tool head can move in the X – Y plane. Findings The kinematic calibration approach is verified by calibration simulations, a Rotation Tool Center Point accuracy test and an experiment of machining an “S”-shaped test specimen. Originality/value The kinematic calibration approach with the MSVD method and VP method could be successfully applied to the 3-DOF parallel tool head and other 3-DOF parallel mechanisms.
A new calibration method for parallel kinematics machine tools using orientation constraint

Xiao-Dong Ren,Zu-Ren Feng,Cheng-Ping Su

DOI: https://doi.org/10.1016/j.ijmachtools.2009.03.004

IF: 10.331

2009-01-01

International Journal of Machine Tools and Manufacture

Abstract:This paper considers the problem of improving the accuracy of parallel kinematics machine tools through a low-cost and effective calibration method. A novel orientation constraint of keeping two attitude angles of the end-effector constant is presented to derive the calibration algorithm with special insight on the effect of using various combinations of two angles. The orientation constraint of the selected combination is realized physically through leveling a commercial biaxial inclinometer installed on the end-effector. Benefits of the proposed method include exempting the needs for precise pose (position and orientation) measurement and for mechanical fixtures, as well as rendering the independence of the measuring range and angular positioning accuracy of the inclinometer. Simulation based on the geometry of the Stewart platform of XJ-HEXA shows the position and orientation accuracy can reach 0.1mm and 0.01° after calibration, when using an inclinometer with the repeatability of 0.001° and measuring the leg lengths with the precision of 0.002mm at 80 configurations. Experiments on XJ-HEXA further verify the effectiveness of the proposed method.
Step-by-step Self-Calibration of a 3-DOF Planar Parallel Kinematic Machine Tool with Actuation Redundancy

CHANG Peng,LI Tiemin,LIU Xinjun

DOI: https://doi.org/10.3321/j.issn:1000-0054.2008.05.012

2008-01-01

Abstract:Minimal linear combinations (MLCs) of the error parameters were used to develop a step-by-step self-calibration method for a 3-DOF planar parallel kinematic machine tool with actuation redundancy.All the engineering measurements were given based on error model outputs and mechanism degrees of freedom,with the parameter identification analyses of each measurement then providing a different set of MLCs.The method takes into account the identification integrity and observability,including step-by-step measurement,parameter identification,and error compensation.Simulations show that this robust,effective method eliminates parameters not affecting the final precision and increases the parameter identification accuracies in each step,with estimated errors matching well with their specified values.
Kinematic calibration of a 5-axis parallel machining robot based on dimensionless error mapping matrix

Xuan Luo,Fugui Xie,Xin-Jun Liu,Zenghui Xie

DOI: https://doi.org/10.1016/j.rcim.2021.102115

2021-08-01

Abstract:<p>Accuracy problem is one of the most challenging issues for the application of parallel robots in manufacturing industry, and kinematic calibration is a feasible approach to solve it. Although lots of researches have brought up a diversity of calibration methods, there are still rooms for the improvement of the accuracy, efficiency and robustness of these calibration effects. In this paper, an improved method for kinematic calibration of a 5-axis parallel machining robot is proposed, which includes a new forward kinematic solution (FKS) based on dual quaternion and a modified error modeling process leading to dimensionless error mapping matrixes (EMMs). On this basis, an iterative identification procedure is schemed, and the kinematics and identification simulations are carried out. The kinematics simulation results show that the proposed FKS has wider convergence range and faster computation speed than <em>Levenberg-Marquardt</em> algorithm, while the identification simulation results show that the residual pose errors with the proposed dimensionless EMMs are lower than that with the conventional EMM in various units. Additionally, the procedure of the full pose measurement with a laser tracker and an auxiliary tool is introduced, and thereby the contrast experiments of kinematic calibration on the prototype are conducted. The experiment results indicate that the residual position and orientation errors based on the dimensionless EMM decrease by 97.67% and 86.85% of the original values, respectively, at least, and by 76.77% and 38.65% of that based on the conventional EMM, respectively, at most. Consequently, it is further confirmed that the proposed calibration method is effective in enhancing the identification accuracy of the geometric errors and improving the positioning accuracy of the studied parallel robot.</p>

robotics,computer science, interdisciplinary applications,engineering, manufacturing
A Calibration Method for Overconstrained Spatial Translational Parallel Manipulators

Li Fengchun,Zeng Qiang,Kornel F. Ehmann,Cao Jian,Li Tiemin

DOI: https://doi.org/10.1016/j.rcim.2018.12.002

IF: 10.103

2018-01-01

Robotics and Computer-Integrated Manufacturing

Abstract:A calibration method for overconstrained spatial translational parallel mechanisms is proposed. The calibration of a Tri-pyramid overconstrained parallel robot is used as a vehicle to demonstrate the methodology and verify its feasibility. The proposed methodology consists of transforming the overconstrained mechanism of the robot into a non-overconstrained mechanism by replacing its redundant constraints with generalized forces (couples). The kinematic model of the non-overconstrained mechanism is derived using vector loops while its mechanical model is established by the energy method. An integrated kinematic model of the original overconstrained parallel robot is subsequently established by expressing the actual position of the end effector as the sum of the position derived by the kinematic model of the non-overconstrained mechanism and of the force-induced deformations at the end effector derived from the mechanical model. To assess the feasibility and the attainable improvements in accuracy through calibration, the positions of the end effector of the Tri-pyramid robot were measured by a method that uses a Double Ball Bar (DBB) and a 3-axes linear stage with micrometers. Based on the integrated kinematic model of the robot and the measured data, its structural parameters were identified by the Newton-Raphson iteration and least squares methods to complete the calibration. The calibration result shows that accuracy improvements on the order of 90% are achievable.
Automated Measurement and Hybrid Adaptive Identification Method for Kinematic Calibration of Hybrid Machine Tools

Liping Wang,Mengyu Li,Guang Yu,Weitao Li,Xiangyu Kong

DOI: https://doi.org/10.1016/j.measurement.2023.113638

IF: 5.6

2023-01-01

Measurement

Abstract:Kinematic calibration is an effective method for ensuring the accuracy of hybrid machine tools. Traditional calibration methods are limited by cumbersome operations and poor algorithm robustness. In this study, measurement methods and identification algorithms are studied, and a new calibration method is proposed. First, the configuration of the hybrid machine tool is described, and an error model is constructed. Then, an automated measurement method of tool center point position error for multiple test arbors is proposed using the R-test device. Subsequently, a hybrid adaptive identification algorithm is proposed by sequentially solving the unit inhomogeneity of the identification model, the rank deficiency produced by incomplete measurements, and the multicollinearity between error parameters. Finally, the efficacy of the proposed calibration method is verified through simulations and experiments. The proposed method significantly improves the calibration efficiency and accuracy and proposes a new solution for automated calibration.

Kinematic calibration of the 3 degree of freedom redundantly actuated spatial parallel module of a five axis hybrid machine:

A United Kinematic Calibration Method for a Dual-Machine System

Kinematic Modeling and Base Frame Calibration of a Dual-Machine-based Drilling and Riveting System for Aircraft Panel Assembly

Kinematic Calibration Of The 3-Dof Parallel Module Of A 5-Axis Hybrid Milling Machine

A Hybrid Analytical and Data-driven Modeling Approach for Calibration of Heavy-duty Cartesian Robot

Kinematic Calibration of Gantry Hybrid Machine Tool Based on Estimation Error and Local Measurement Information

Kinematical calibration of a hybrid machine tool with Regularization method

Optimization of a redundantly actuated parallel kinematic mechanism for a 5-degree-of-freedom hybrid machine tool

Kinematic Calibration Method with High Measurement Efficiency and Robust Identification for Hybrid Machine Tools

Kinematic Calibration of a Hybrid Machine Tool with Constrained Least Square Method

Measurement Trajectory Evaluation and Error Compensation for Kinematic Calibration of a 5-Axis Hybrid Machine Tool

The Calibration Simulation of a Five-axis Parallel Machine Tool

Accuracy Analysis and Calibration of Gantry Hybrid Machine Tool

Complete Kinematic Calibration of a 6-RRRPRR Parallel Kinematic Machine Based on the Optimal Measurement Configurations

A Kinematic Calibration Method of a 3T1R 4-Degree-of-freedom Symmetrical Parallel Manipulator

Kinematic Calibration of a 3-DOF Parallel Tool Head.

A new calibration method for parallel kinematics machine tools using orientation constraint

Step-by-step Self-Calibration of a 3-DOF Planar Parallel Kinematic Machine Tool with Actuation Redundancy

Kinematic calibration of a 5-axis parallel machining robot based on dimensionless error mapping matrix

A Calibration Method for Overconstrained Spatial Translational Parallel Manipulators

Automated Measurement and Hybrid Adaptive Identification Method for Kinematic Calibration of Hybrid Machine Tools