Abstract:The spectroscopic detection of ammonium (NH4+) has great significance. With the development of microfluidics, microfluidic spectroscopic analysis aiming at rapid, portable and multi-component detection has realized tremendous achievements. However, the excessive consumption of the indicating material which exists all the time has not been settled yet. Zinc porphyrin, being a natural chromophore, can reversibly detect NH4+ and settle the problem. But it suffers from the lack of selectivity. In allusion to these issues, a coupled microfluidic chip which consists of a reaction chip, a gas-diffusion chip and a detection chip is fabricated in our experiments. The reaction chip made of polydimethylsiloxane can convert NH4+ into NH3. The gas-diffusion chip which is made of two glass chips and a piece of polydimethylsiloxane gas-diffusion membrane allows NH3 diffuses into the detection solution. The detection chip immobilizes the indicating material tightly through the multi-layer structure. The indicating material fabricated by dying zinc porphyrin on the surface of the cation exchange resin permanently will turn from green to purple when it meets NH3 and will turn reversely into green when pure water is around. Using the coupled chip as the analytical platform, we set up a miniaturized spectroscopic detection system. With a portable spectrometer being the analytical instrument, we detect NH4+ by the transmission spectrum intensity change at the wavelength of 450 nm and study three factors that could affect the detection performance: the thickness of the gas-diffusion membrane, the flow rate and the dosage of the indicating material. First, we confirm the reversibility of the indicating process and settle the issue of indicating material consumption by the spectrum change intensity. The time responses show the rapidity of the indicating process. Then through the comparison to the contrast experiment, the high selectivity of the indicating process is demonstrated because the interference has no influence and the spectrum change is attributed merely to NH3. The relationship between the membrane thickness and the spectrum intensity change is obtained by changing the thickness of the gas-diffusion membrane in the gas-diffusion chip. Results show that the increase of the membrane thickness leads to a worse detection performance, but the outcome remains stable when the thickness is less than 10 mu m. So 10 mu m is selected as the optimal thickness in consideration of the mechanical strength. The impact of the flow rate is investigated afterwards. The results exhibit that the increase of the flow rate will decrease the spectrum intensity change, but the performance becomes unchanged when flow rate is less than 5 mu L . min(-1). Last, how the dosage of the indicating material impacts the results is studied. It is demonstrated that both excessive and inadequate indicating material will deteriorate the performance. So 5 mg is selected as the optimal amount. The spectroscopic detection system which uses the coupled chip as the analytical platform has the advantages of small volume, high economy, rapid response and realizes highly selective and reversible NH4+ detection.

Reversible Microfluidic Measurement with Zinc Tetraphenylporphyrin Aiming at Slipping NH3detection

The spin-coating-based immobilization of ZnTPP-dyed cation exchange resin microbeads for reversible ammonia detection

The Reversible Ammonium Detection Based on the Coupled Microfluidic Chipand the Investigation of the Impact Factors

A Reversible Spectrophotometric Method Based on a Coupled Microfluidic Chip for Highly Selective Ammonium Detection

Au nanoparticle-modified ZnO/SnO2 heterojunction nanocomposites for highly sensitive detection of NH3

Microfluidic Chip Detection Instrument With High Signal-To-Noise Ratio

Microfluidic chip-based flow injection system with gas diffusion separation and photometric detection

A Microfluidic Chip Capable of Switching W/O Droplets to Vertical Laminar Flow for Electrochemical Detection of Droplet Contents.

High Performance Gas Sensors Based on In-Situ Fabricated ZnO/polyaniline Nanocomposite: the Effect of Morphology on the Sensing Properties

Reflection Photometric Detection On A Paper-Backed Immobilized Reagent Surface In A Pdms Microfluidic Chip Flow Injection System Integrated With Gas Diffusion Separation

Graphene Oxide-Coated Mach-Zehnder Interferometer Based Ammonia Gas Sensor

Construction of "ant-like tentacle" structure for ultra-sensitive detection of low-concentration ammonia through colorimetric fluorescent dual-signal gas-sensitive cotton fabric

Zno Nanoparticles/Reduced Graphene Oxide Bilayer Thin Films for Improved Nh3-Sensing Performances at Room Temperature

Dual-response and color-changing fluorescent sensor for N2H4 and Zn2+

Zinc(II)porphyrin-poly(lactic acid) nanoporous fiber membrane for ammonia gas detection

Digital Microfluidic Chip for Rapid Portable Detection of Mercury(Ii)

Porous Flexible Polyaniline/polyvinylidene Fluoride Composite Film for Trace-Level NH3 Detection at Room Temperature

Polyaniline @ Porous Nanosphere SnO2/Zn2SnO4 Nanohybrid for Selective Room Temperature Flexible NH3 Sensor

Preparation and study of ammonia gas sensor based on ZnO/CuO heterojunction with high performance at room temperature

Ultramicro Interdigitated Array Electrode Chip with Optimized Construction for Detection of Ammonia Nitrogen in Water

An in-line Mach-Zehnder Interferometer Using Thin-core Fiber for Ammonia Gas Sensing With High Sensitivity