Abstract:The effect of normal stress variations on fault frictional strength has been extensively characterized in laboratory experiments and modelling studies based on a rate-and-state-dependent fault friction formalism. However, the role of pore pressure changes during injection-induced fault reactivation and associated frictional phenomena is still not well understood. We apply rate-and-state friction (RSF) theory in finite element models to investigate the effect of fluid pressurization rate on fault (re)activation and on the resulting frictional slip characteristics at the laboratory scale. We consider a stepwise injection scenario where each fluid injection cycle consists of a fluid pressurization phase followed by a constant fluid pressure phase. We first calibrate our model formulation to recently published laboratory results of injection-driven shear slip experiments. In a second stage, we perform a parametric study by varying fluid pressurization rates to cover a higher dimensional parameter space. We demonstrate that, for high permeability laboratory samples, the energy release rate associated with fault reactivation can be effectively controlled by a stepwise fluid injection scheme, i.e. by the applied fluid pressurization rate and the duration of the constant pressure phase between each successive fluid pressurization phase. We observe a gradual transition from fault creep to slow stick-slip as the fluid pressurization rate increases. Furthermore, computed peak velocities for an extended range of fluid pressurization rate scenarios (0.5 MPa/min to 10 MPa/min) indicate a non-linear (power-law) relationship between the imposed fluid pressurization rate and the peak slip velocities, and consequently with the energy release rate, for scenarios with a fluid pressurization rate higher than a critical value of 4 MPa/min. We also observe that higher pressurization rates cause a delay in the stress release by the fault. We therefore argue that by adopting a stepwise fluid injection scheme with lower fluid pressurization rates may provide the operator with a better control over potential induced seismicity. The implications for field-scale applications that we can derive from our study are limited by the high matrix and fault permeability of the selected sample and the direct hydraulic connection between the injection well and the fault, which may not necessarily represent the conditions typical for fracture dominated deep geothermal reservoirs. Nevertheless, our results can serve as a basis for further laboratory experiments and field-scale modelling studies focused on better understanding the impact of stepwise injection protocols on fluid injection-induced seismicity.

Injection-induced Slip Heterogeneity on Faults in Shale Reservoirs

Numerical simulation of fluid injection-induced fault slip in heterogeneous shale formations

Impacts of Rate of Change in Effective Stress and Inertial Effects on Fault Slip Behavior: New Insights Into Injection‐Induced Earthquakes

Modeling of Injection Induced Seismic Events

Changes of Slip Rate and Slip‐Plane Orientation by Fault Geometrical Complexities During Fluid Injection

FEM Simulation of Fault Reactivation Induced with Hydraulic Fracturing in the Shangluo Region of Sichuan Province

Numerical investigation of the stress regime effect on injection-induced fault reactivation and associated seismicity

Injection-driven fracture instability in granite: Mechanism and implications

Investigation of dynamic pore pressure in shale gas reservoir during the multi-fracturing and its influence on fault slip

Numerical investigation of the effect of fluid pressurization rate on laboratory-scale injection-induced fault slip

Mitigation of injection-induced seismicity on undrained faults in granite using cyclic fluid injection: A laboratory study

Fluid-driven aseismic fault slip with permeability enhancement and dilatancy

A laboratory study on fault slip caused by fluid injection directly versus indirectly into a fault: implications for induced seismicity in EGSs

The Role of Fault-Zone Architectural Elements on Pore Pressure Propagation and Induced Seismicity

Laboratory Simulation of Injection-Induced Shear Slip on Saw-Cut Sandstone Fractures under Different Boundary Conditions

Numerical analysis of injection-induced fault reactivation using hydro-mechanical coupled finite element model with cohesive zone elements

Impact of fault slip induced by water injection on casing deformation: a numerical study

Frictional evolution process and stability properties of Longmaxi shale under fluid injection

Decomposing significant factors of Coulomb stress and its components in injection-induced seismicity

Implications for fault reactivation and seismicity induced by hydraulic fracturing

Cyclic Water Injection Potentially Mitigates Seismic Risks by Promoting Slow and Stable Slip of a Natural Fracture in Granite