Abstract:The low-alloyed transformation induced plasticity (TRIP) steels demonstrate an improved combination of strength and ductility, and have became a promising candidate for the application of automotive bodies to reduce the weight without the loss of crash-worthiness. The typical microstructure of TRIP steels consists of the ferrite matrix and a dispersion of bainite, martensite and the retained austenite. The existence of an amount of metastable retained austenite is responsible for the improved mechanical properties, resulted from the enhanced strain hardening capabilities of TRIP steels due to the strain-induced martensitic transformation during straining. The carbon content is considered as an important factor that influences the amount and stability of the retained austenite. In the present work, two cold-rolled C-Mn-Al-Si TRIP steels with different carbon contents, (0.1% and 0.2%, mass fraction) were fabricated by intercritical annealing and isothermal transformation. The microstructures and the mechanical behaviors of the used steels were investigated by OM, XRD and uniaxial tensile tests at room temperature. The results indicated that with the same isothermal transformation time at 400 degrees C, the steels with high carbon content obtained lower fraction of bainite and larger fraction of martensite, and demonstrated higher strength and larger elongation than those of steels with low carbon content. The excellent ductility of steels with high carbon content was mainly attributed to its strong TRIP effect during deformation, resulted from the larger fraction of retained austenite as well as the higher carbon content of retained asutenite in the multiphase microstructure. The value of the product of tensile strength and total elongation, representing the combination of strength and ductility of steels, was increased linearly with the increase of the value of the product of volume fraction and carbon content of retained austenite, which could be used to characterize the TRIP effect. Variation of the formation rate of strain-induced martensite was similar to that of the incremental strain hardening exponent with strain during deformation, further proved the important role of TRIP effect in influencing the strain hardening capabilities of TRIP steels.

M3 Microstructure Control Theory and Technology of the Third-Generation Automotive Steels with High Strength and High Ductility

Microstructure and Performance Control Technology of the 3rd Generation Auto Sheet Steels

Research on Microstructure and Property of Hot-Rolled 700MPa Grade Automobile Sheet

The 3rd Generation Automobile Sheet Steels Presenting with Ultrahigh Strength and High Ductility

On the Performance Improvement of Steels through M<sup>3</sup>Structure Control

On the Performance Improvement of Steels through M<Superscript>3</Superscript> Structure Control

Microstructures and Mechanical Properties of the Third Generation Automobile Steels Fabricated by ART-annealing

Research Progress of Microstructure Control and Strengthening Mechanism of QPT Process Advanced Steel with High Strength and Toughness

Microstructure and Properties of a Low Carbon Ti-V Microalloyed Steel

Research and development of steel for ultra-light automotive

Microstructure Control of Hot Rolled Trip Steel Based on Dynamic Transformation of Undercooled Austenite I. Prior Austenite Grain Size

The Role of Transformation‐Induced Plasticity in the Development of Advanced High Strength Steels

CONTROL AND DESIGN OF MICROSTRUCTURE IN STEELS (Ⅱ)

Effect Of Carbon Content On Microstructure And Mechanical Properties Of Cold-Rolled C-Mn-Al-Si Trip Steel

Microstructure Design and Feasibility of Hot Stamping for New Generation High Strength Multi-Phase Steels

MICROSTRUCTURE CONTROL OF HOT ROLLED TRIP STEEL BASED ON DYNAMIC TRANSFORMATION OF UNDERCOOLED AUSTENITE II. Cooling Rate after Dynamic Transformation of Undercooled Austenite

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

New developments of advanced high-strength steels for automotive applications

Recent progress in microstructural evolution, mechanical and corrosion properties of medium-Mn steel

Microstructure and Mechanical Properties of Microalloyed High-Strength Transformation-Induced Plasticity Steels

Physical metallurgy of medium-Mn advanced high-strength steels