Granulite facies metamorphism and petrogenesis of granite (II) : Quantitative modeling of the HT-UHT phase equilibria for metapelites and the petrogenesis of S-type granite

Wei ChunJing

IF: 1.468

2016-01-01

Acta Petrologica Sinica

Abstract:The mineral assemblages and textural relations of high-temperature (HT) and ultrahigh temperature (UHT) metamorphic rocks depend on the prograde partial melting reactions, partial melt loss and partial retrogression. Using phase modeling approaches, the prograde partial melting reactions, P-T conditions, melt production and loss, and the chemical compositions of melt and residues during a melting process can be quantitatively modeled, which is very helpful for understanding the HT-UHT metamorphic processes and petrogenesis of granitoids. Phase modeling for an average pelite sample (APR) suggests that there are five types of melting reactions during an isobaric (0.8GPa) heating process, involving fluid-saturated solidus melting (HM), muscovite dehydration melting (MM), biotite dehydration melting (BM), K-feldspar-garnet melting (KGM) and the melting of Al-Fe-Mg silicates (AFM melting) after K-feldspar breakdown. The latter two types of melting mainly occur under UHT conditions. What types of melting reactions occur during decompression in metapelite depends on temperatures; the decompression melting under granulite facies (i.e. 850 degrees C) involves K-feldspar melting (KM), BM, and KGM; the decompression melting under high-amphibolite facies (i.e. 750 degrees C) involves MM and KM; and the decompression melting under UHT granulite facies (i.e. 950 similar to 1000 degrees C) involves KGM and AFM melting. The melt compositions are dependent on melting reactions and P-T conditions. For example, the HM and MM under high amphibolite facies can produce weak para-aluminous trondhjemitic to monzogranitic melt, the KM and BM under granulite facies can produce strong para-aluminous monzogranitic melt, the KGM and AFM under UHT granulite facies of medium-pressure can produce strong para-aluminous monzogranitic melt, forming garnet granite, and the AFM melting under UHT granulite facies of low-pressure may produce cordierite granite. Except for the AFM melting under UHT conditions, the other types of melting may cause the residues to be poor in SiO2, Na2O and K2O, rich in FeO and MgO, without obviously changing their Al2O3 and Mg-#. Partially melted rocks under HT-UHT conditions can only preserve the solidus assemblages in cooling processes, but the types and temperatures of the solidus depend on melt loss behavior in the rock. If there is no melt loss or there is melt gain, the rock can only retain the water-saturated solidus, and if there is melt loss, the rock will retain a fluid-absent solidus and the corresponding assemblage. The more the melt is lost, the higher the temperature of the fluid-absent solidus will be. If all melt is lost in a rock, it can record the highest temperature ever reached. As a consequence, rocks from different domains in a granulite facies region, or from different localities in a granulite outcrop, can record different temperatures due to different degrees of melt loss. In high-grade rocks with partial melting, zircon will be dissolved as melt increases with increasing temperature, and zircon growth can only occur during cooling. Thus, the newly grown zircon in granulites should record the age when cooled to the solidus, rather than the age of the peak pressure or temperature stages. A high-pressure politic granulite tends to reach equilibrium when there is progressive melting during an isothermal decompression (ITD), but if the decompression is so fast to uplift the rock to shallow crust in a short time, the textures characteristic of the ITD evolution involving residual rutile and kyanite, and cordierite corona around garnet can appear. In this case, the cooling age recorded by zircon may not be much younger than the peak stage (10 similar to 30Myr). However, if a high-pressure pelitic granulite is uplifted to mid- or lower crust and followed by an IBC evolution, it will develop characteristic IBC textures due to the presence of retained melt, with the granulite assemblages being overprinted by amphibolite facies, forming the biotite-sillimanite selvages, retrograde muscovite and muscovite bearing leucosomes. In this case, the cooling age recorded by zircon may be much younger than the peak stage (similar to 100Myr). Melting in high-grade rocks may cause decreasing of water activity, and thus, the water activity would be much lower in the granulites resulted from the residues after melt loss. From this point of view, the low water activity in most granulites should be a result of granulite facies metamorphism, rather than one of its prerequisites. Occurrence of multi-phase granulite facies metamorphism in a granulite region depends on fluid behaviors. For a fluid-saturated rock at subsolidus conditions,. its partial melting starts from the fluid-saturated solidus, and followed by the dehydration melting of hydrous phases and melting of anhydrous phases. These melting reactions are controlled by internally buffered fluid, forming one stage equilibrium assemblage at the granulite peak temperature, obscuring the pre-peak prograde information. However, metamorphism of the fluid-unsaturated rocks (i.e. the existed granulite or intrusion) is controlled by external fluid-infiltration, closely related to structural deformation. If a granulite terrane is overprinted by a late phase granulite facies metamorphism, in high-strain domains that are favorable for fluid flowing, may occur equilibrium granulite assemblages of the late phase; in low-strain domains, may appear two phases of granulite assemblages with the late phase minerals occurring as coronae or fine-grained intergrowths; while in some very low-strain domains, the early phase assemblages may be preserved.