Abstract:An isolated single polymer suspending in the dilute solution exhibits a collapse transition when switched from good solvent to poor solvent. The transition passes through a thermally reversible intermediate molten globule state holding a characteristic core-shell structure with a concentrated core and a dilute shell, which appears more obvious for shorter chains. Therefore, the collapse transitions of short-chain polymers appear more gradual than those of long-chain polymers. This intermediate molten globule state is interesting because it allows a better understanding of the protein folding and its bio-functions as well as of polymer interface properties. We performed dynamic Monte Carlo simulations to compare the intermediate molten globule state of a single ring polymer to that of a single linear polymer. Their molten globule structures appeared very similar. This observation thus ruled out the specific effect of chain ends, and allowed us to focus on the surface effect of the globules in the intermediate states, which was also obvious for the limited chain length. We observed that, right below the theta point as the critical demixing point for solution of the polymer with infinite chain lengths, the intermediate molten globule states showed two energy states of monomers separately in the core and in the shell, appearing as a coexistence of two concentrations separately deviating from the critical. point. We, therefore, considered the molten globule state as a result of pre-dissolution, similar to the pre-melting phenomenon of single-chain single crystals around their equilibrium melting points. The surface dissolution model was then applied to describe the characteristic core-shell structures near the critical point during collapse transition of single-chain polymers. According to the surface dissolution model, near the critical theta point, the globule-solvent interface energy of the collapsed globules became high, which was then optimized by forming a thin layer of coexisting dilute phase, i.e. replaced by the globule-coil plus coil-solvent interface energy. The situation is something similar to the complete wetting of the vapour on a solid substrate, except that the partial surface dissolution achieves a minimum free energy with an equilibrium thickness of the surface layer. In fact, on the phase diagram, right below the theta point, any concentration deviation from the theta state will enter the metastable region for first-order phase transition. The equilibrium layer thickness defines the soluble length of chain segments on the surface. For a real single-chain polymer, however, the extent of surface dissolution may not be able to reach the equilibrium end, because the topological constraint inside the globule, for example, a knotting, will not allow the equilibrium lengths of chain segments to release at the globule surface. This kind of pre-dissolution behaviours could be unique for polymers at interfaces near the critical point. Since shorter chains make smaller globules, their surface dissolution phenomena become more obvious and their collapse transitions appear more gradual. Owing to the surface dissolution near the critical point for phase separation, the distribution of monomer energy states becomes discontinuous along the direction normal to interface. This behaviour reveals a discrepancy at the molecular level if compared to the traditional theoretical treatment of a continuous concentration gradient along this normal direction for the critical interfaces. Thus, the pre-dissolution model may provide a profound approach to better understand the microscopic nature of polymers at the near-critical fluid-fluid interfaces.

One Intellectual Problem in Polymer Research - the Coil-to-Globule Conformation Transition of Flexible Chains

One Intellectual Problem in Polymer Research-the Coil-to-Globule Conformation Transition of Flexible Chains

Coil–Globule Transition of a Water-Soluble Polymer

Local Coil–helix Transition of Semiflexible Polymers Confined in Spheres

Globule-to-Coil Transition of a Single Homopolymer Chain in Solution

The Phase Behaviour of Single Polyethylene Chains with and Without Fixing One End

Phase Behavior of a Single Polyethylene Chain Confined Between Two Adsorption Walls Part B Polymer Physics

Folding and Formation of Mesoglobules in Dilute Copolymer Solutions

Intermediate Molten Globule State and Its Thermodynamic Interpretation in the Collapse Transition of Single Ring Polymer

Monte Carlo Simulation of Coil-to-Globule Transition of Compact Polymer Chains: Role of Monomer Interacting

The Coil-To-Globule-To-Coil Transition of Linear Polymer Chains in Dilute Aqueous Solutions: Effect of Intrachain Hydrogen Bonding

A Comparison Between the 'Coil-to-globule' Transition of Linear Chains and the "volume Phase Transition" of Spherical Microgels

Kinetic mechanisms of crumpled globule formation

Comparison of the Coil-to-Globule and the Globule-to-Coil Transitions of a Single Poly(N-isopropylacrylamide) Homopolymer Chain in Water

Structural Transformation in the Collapse Transition of the Single Flexible Homopolymer Model

First Observation of the Molten Globule State of a Single Homopolymer Chain.

Unusual Transformation of Polymer Coils in a Mixed Solvent Close to the Critical Point.

Conformations of Two-dimensional Macromolecules and Condensed Structure Modulation

Thermodynamic and Conformational Insights into the Phase Transition of a Single Flexible Homopolymer Chain Using Replica Exchange Monte Carlo Method.

Unconventional Transitions of Poly(N-isopropylacrylamide) upon Heating in the Presence of Multiple Noncovalent Interactions

First Observation of Two-Stage Collapsing Kinetics of A Single Synthetic Polymer Chain