Abstract:Lithium–sulfur (Li–S) batteries are severely hindered by the low sulfur utilization and short cycling life, especially at high rates. One of the effective solutions to address these problems is to improve the sulfiphilicity of lithium polysulfides (LiPSs) and the lithiophilicity of the lithium anode. However, it is a great challenge to simultaneously optimize both aspects. Herein, by incorporating the merits of strong absorbability and high conductivity of SnS with good catalytic capability of ZnS, a ZnS-SnS heterojunction coated with a polydopamine-derived N-doped carbon shell (denoted as ) with uniform cubic morphology was obtained and compared with the ZnS-SnS2@NC heterostructure and its single-component counterparts ( and SnS2@NC). Theoretical calculations, ex situ XANES, and in situ Raman spectrum were utilized to elucidate rapid anchoring-diffusion-transformation of LiPSs, inhibition of the shuttling effect, and improvement of the sulfur electrochemistry of bimetal ZnS-SnS heterostructure at the molecular level. When applied as a modification layer coated on the separator, the cell with optimized lithiophilicity and sulfiphilicity enables desirable sulfur electrochemistry, including high reversibility of 1149 mAh g–1 for 300 cycles at 0.2 C, high rate performance of 661 mAh g–1 at 10 C, and long cycle life with a low fading rate of 0.0126% each cycle after 2000 cycles at 4 C. Furthermore, a favorable areal capacity of 8.27 mAh cm–2 is maintained under high sulfur mass loading of 10.3 mg cm–2. This work furnishes a feasible scheme to the rational design of bimetal sulfides heterostructures and boosts the development of other electrochemical applications.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsnano.1c00270?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsnano.1c00270</a>.Additional experimental sections (materials synthesis, characterizations, and DFT calculations); SEM, TEM, XRD, TG, XPS, BET, and XANES characterizations of the samples; CV curves; discharge–charge profiles and cycle performance of various electrodes; in situ Raman tests; optimized geometries of LiPSs; Tables S1–S6: Li+ diffusion rates, EIS fitting, and comparisons of electrochemical performance (<a class="ext-link" href="/doi/suppl/10.1021/acsnano.1c00270/suppl_file/nn1c00270_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Oxygen Vacancy Enhanced Catalytic Oxidation of H2S Based on ZnO Incoperated N-doped Hollow Carbon Nanofibers for Cathodes Construction of High-performance Li-S Batteries

A Nitrogen/Oxygen Dual-Doped Porous Carbon with High Catalytic Conversion Ability Toward Polysulfides for Advanced Lithium–Sulfur Batteries

Selective catalytic oxidation of pollutant H2S over Co-decorated hollow N-doped carbon nanofibers for high-performance Li-S batteries

Enhanced catalysis LiS<sub>3</sub> of radical-to-polysulfide interconversion <i>via</i> increased sulfur vacancies in lithium-sulfur batteries

Integration of Desulfurization and Lithium–Sulfur Batteries Enabled by Amino‐Functionalized Porous Carbon Nanofibers

Sulfophobic and Vacancy Design Enables Self‐Cleaning Electrodes for Efficient Desulfurization and Concurrent Hydrogen Evolution with Low Energy Consumption

Multifunctional ZnCo 2 O 4 Quantum Dots Encapsulated In Carbon Carrier for Anchoring/Catalyzing Polysulfides and Self‐Repairing Lithium Metal Anode in Lithium‐Sulfur Batteries

Catalytic Oxidation of Li 2 S on the Surface of Metal Sulfides for Li−S Batteries

Oxygen Defect‐Rich WO3−x–W3N4 Mott–Schottky Heterojunctions Enabling Bidirectional Catalysis for Sulfur Cathode

ZnS-SnS@NC Heterostructure as Robust Lithiophilicity and Sulfiphilicity Mediator toward High-Rate and Long-Life Lithium–Sulfur Batteries

A Self–Regulatory Organosulfur Copolymer Cathode towards High Performance Lithium–Sulfur Batteries

Hierarchical mesoporous heteroatom-doped carbon accelerating the adsorption and conversion of polysulfide for high performance Lithium–Sulfur batteries

Rich Heterointerfaces Enabling Rapid Polysulfides Conversion and Regulated Li2S Deposition for High-Performance Lithium-Sulfur Batteries.

Regulating Li2S Deposition and Accelerating Conversion Kinetics Through Intracavity ZnS Toward Low-Temperature Lithium-Sulfur Batteries.

A hollow Co0.12Ni1.88S2/NiO heterostructure that synergistically facilitates lithium polysulfide adsorption and conversion for lithium-sulfur batteries

Catalytic Interfaces‐Enriched Hybrid Hollow Spheres Sulfur Host for Advanced Li–S Batteries

Coordinated Immobilization and Rapid Conversion of Polysulfide Enabled by a Hollow Metal Oxide/Sulfide/Nitrogen‐Doped Carbon Heterostructure for Long‐Cycle‐Life Lithium‐Sulfur Batteries

Engineering the Conductive Network of Metal Oxide‐Based Sulfur Cathode toward Efficient and Longevous Lithium–Sulfur Batteries

InOOH as an efficient bidirectional catalyst for accelerated polysulfides conversion to enable high-performance lithium-sulfur batteries

High-entropy perovskite oxide nanofibers as efficient bidirectional electrocatalyst of liquid-solid conversion processes in lithium-sulfur batteries

Coupling highly dispersed Sb2S3 nanodots with nitrogen/sulfur dual-doped porous carbon nanosheets for efficient immobilization and catalysis of polysulfides conversion