Abstract:The volatiles and char derived from municipal solid waste (MSW) pyrolysis can be catalytically reformed and gasified using high-temperature CO 2 (HT-CO 2 ) as gasifying agent and char as a catalyst simultaneously to obtain high quality synthesis gas, but the reactor's design for this purpose is still a question. In this research, the contact configuration between the HT-CO 2 , the volatile compounds, and the char from MSW pyrolysis were studied to understand the relevant reaction behaviors and to establish guidelines for the reactor's design. Three contact modes were designed, including: M1, where volatiles and HT-CO 2 contact first, then contact the char; M2, where volatiles, CO 2 , and char contact simultaneously at the bottom of the char layer; and M3, where CO 2 contacts with the char first, then the volatiles contact in the middle of the char layer. The temperature evolution in the char layer, the yields and properties of the resultant combustible gases, used char, and tar were investigated. Experimental results revealed that the contact mode significantly affected the levels of char gasification and volatiles' reforming. For M1, intense thermal cracking of volatiles occurred and 65.41% of the input heat of HT-CO 2 was consumed for thermal cracking, resulting in substantial carbon deposition and limited energy transfer from char to the synthesis gas. While, the char contacting HT-CO 2 firstly in M3 improved its catalytic activity, causing 73.33 % of the input heat utilized for gasification and reforming; as a result, the maximum synthesis gas yield of 0.71 Nm 3 /kg MSW and gas energy ratio of 76.3 % were obtained respectively in M3 with the lowest tar yield of 5.45 %; additionally, the used char corresponded to the highest specific surface area of 10.12 m 2 /g. Ultimately, M3 is constructive and recommended, and the findings of this study offer helpful guidance for the design of pyro-gasification reactors.

Biochar and Pyrolytic Gas Properties from Pyrolysis of Simulated Municipal Solid Waste (SMSW) under Pyrolytic Gas Atmosphere

Municipal Solid Waste Pyrolysis under Circulated Pyrolytic Gas Atmosphere

Pyrolysis of typical solid wastes in a continuously operated microwave-assisted auger pyrolyser: Char characterization, analysis and energy balance

Effects of Sludge Pyrolysis Temperature and Atmosphere on Characteristics of Biochar and Gaseous Products

Gas Emissions from Blends of Bituminous Coal and Biomass Chars under Different Pyrolysis Conditions

Char Characteristics of Municipal Solid Waste Prepared under N2 and CO2 Atmospheres

Pyrolyzed Waste Stream and Biochar Performance Evaluation in Food Waste Anaerobic Digestion

A comparison between CO2 gasification of various bioass chars and coal char

Effects of N2/CO2 Atmosphere on the Pyrolysis Characteristics for Municipal Solid Waste Pellets

Pyrolysis Gas Characteristics of Municipal Solid Waste

A Novel Integrated Pyrolysis-Gasification Technology for Improving Quality of Bio-Gases from Multisource Solid Wastes

Product characteristics and heat of reaction of municipal solid waste in pyrolysis and gasification at low temperatures

Pyrolysis of Biomass Wastes into Carbon Materials

Upgrading gas and oil products of the municipal solid waste pyrolysis process by exploiting in-situ interactions between the volatile compounds and the char

Syngas Production from Pyrolysis of Municipal Solid Waste (MSW) with Dolomite As Downstream Catalysts

MSW pyro-gasification using high-temperature CO 2 as gasifying agent: Influence of contact mode between CO 2 , char and volatiles on final products

PYROLYTIC KINETICS OF COMBUSTIBLE OF MSW

Hot Char-Catalytic Reforming of Volatiles from MSW Pyrolysis

Decoupling Study of Municipal Solid Waste Gasification: Effect of Pelletization on Pyrolysis and Gasification of Pyrolytic Char

Municipal solid wastes pyro-gasification using high-temperature flue gas as heating resource and gasifying agent

TGA Pyrolysis and Gasification of Combustible Municipal Solid Waste