Abstract:In a Middle East oilfield, reservoirs are characterized by high temperature, high salinity, high CO2 / H2S content, and low pH, which leads to harsh corrosive environment. With development of the field, the increasing water cut and application of CO2-EOR technology have made tubulars face greater corrosion risk. Therefore, employing feasible anti-corrosion coating to corresponding part is one of the most effective technologies to mitigate downhole corrosion risk, reduce workover, and avoid potential HSE risk. Corrosion environment characteristics was thoroughly studied by reviewing production history, water chemistry, gas composition, downhole temperature and pressure, logging data, etc. Downhole corrosion condition was classified based on NACE standard RP0775-2005. Based on this, the field simulated corrosion tests were carried out on the self-healing coating in high-temperature and pressure autoclave. The self-healing coating was fabricated by loading slow-released MBT-LDH nanocomposites to the phenolic epoxy resin. For comparison, the similar experiment was also conducted on commercial phenolic epoxy coating and heavy-duty coating. The anti-corrosion performance and applicability of the coatings were characterized by SEM/EDS, FT-IR and EIS. Two main factors have been considered while evaluating the coating options, the first consideration is reliability and durability of the coating. If the coating is easily damaged during operation and transportation, its protective performance decreases after damage, which cannot be easily repaired again. The second consideration is the compatibility of the coating in a harsh downhole environment. Considering the above aspects, the self-healing coating, commercial phenolic epoxy coating and commercial heavy-duty were selected. After corrosion tests, a small amount of corrosion products can be observed on the commercial phenolic epoxy coating surface both in the simulated well head and bottom condition. There were no obvious morphology changes on the heavy-duty coating surface in both condition, however, chemical degradation of the coating was observed in well bottom condition. Notably, the self-healing coating appeared no peeling, bubbling and other defects in both conditions. There were corrosion products identified in the pre-destructed area of the coating, which attributed to the localized inhibition of the self-healing coating. This paper investigated the corrosion resistance coating technology, including coating selection evaluation, typical tubing thread area protection technique, coating chemical and physical property analysis and evaluation. The study also recommended coating applicability for the target reservoir. The results suggested that phenolic epoxy based self-healing coating show robust anti-corrosion performance and can be used in the downhole containing CO2 and H2S.

Design and Performance of A Packer Fluid in H2S/CO2 Environments

Corrosion-resistant systems of formate packer fluid for G3/N80/TP110SS pipes at high temperature, high pressure and high H2S/CO2 ratios

Investigation on mechanical properties and corrosion behavior of rubber for packer in CO2-H2S gas well

Study on Anti-Corrosion Performance and Applicability of Self-Healing Coating for Tubulars in CO2 /H2S Environment

Studies on Couple Corrosion of Casing Steel in Completion Fluid and Inhibitor Selection for Wenchang Oil Fields

Preparation of a Corrosion Inhibitor Preventing H2S Corrosion and Coupon Test

Research on the Multifactor Synergistic Corrosion of N80 and P110 Steel Tubing in Shale Gas Wells in Sichuan Basin

Corrosion Behavior and Mechanical Performance of Drill Pipe Steel in a CO2/H2S-Drilling-Fluid Environment

Corrosion Behavior of Tubing in High-Salinity Formation Water Environment Containing H2S/CO2 in Yingzhong Block

PREPARATION OF A CORROSION INHIBITOR PREVENTING H_2S CORROSION AND COUPON TEST

A New Drilling Fluid System for Temporary Plugging of Low Permeability Carbonate Reservoirs Containing H2S and CO2

Revealing the Deterioration Effect of Scale Inhibitor on the Performance of Corrosion Inhibitor under Dynamic Conditions

Design of water-based annulus protection fluid for CO2 flooding injection well

Development of a novel packer fluid for high-temperature and high-pressure oil and gas wells with using design of experiments and artificial intelligence

Experimental Studies on CO2 Corrosion of Rubber Materials for Packer under Compressive Stress in Gas Wells

Experimental Study on Corrosion of J55 Casing Steel and N80 Tubing Steel in High Pressure and High Temperature Solution Containing CO2 and NaCl

Failure evaluations for packers in multistage fracturing technology with immobile strings

Corrosion Inhibitor Selection Study for Topside Unit of a Subsea Platform

CORROSION PROBLEMS INDUCED BY WATERS CONTAINING LOW H_2S AND MEDIUM CO_2 FROM GAS WELLS AT A GAS FIELD

Effect of Service Environmental Parameters on Electrochemical Corrosion Behavior of L80 Casing Steel

Reliability Analysis of Elastic Graphite Packer in Heat Injection Well During Oil Shale In-Situ Conversion