The parameter study of terahertz free-electron laser oscillator based on electrostatic accelerator *

Ailin Wu,Qika Jia,Juhao Wu

2013-01-01

Abstract:Free-Electron Laser Oscillator based on Electrostatic Accelerator (EA-FELO) is one of the best methods to realize the powerful terahertz source, which can not only produce high power, but also obtain coherent and tunable wavelength. In this paper, we investigate the effects of the main parameters in this scheme, including the initial electron-beam energy spread, emittance and beam current. Besides, the influence of the radius of the mirrors and the position of the undulator on FEL performance is also studied. The numerical results from 1D FEL Oscillator simulation code FELO are presented, and show that this compact device could achieve the terahertz light with the peak output power is about 5.3kW. INTRODUCTION Since the terahertz sources provide wide applications in medical science, material science and industry, a compact, wavelength tunable and high-power THz source attracted much attention in many laboratories [1]. It is noteworthy that EA-FELO could achieve high average power generation, high energy conversion efficiency and high spectral purity, because of its CW operation. successfully, such as University of California Santa Barbara FEL (UCSBFEL) employed a 6MeV Pelletron accelerator and obtained 2.5 mm to 30 μm FEL [2], Israel FEL based on a 6 MeV EN tandem acceleration can produce average power of 1kW in the range of 70-130 GHz [3]. Recently, we also have made some primary research and analysis on it [4-5]. On the basis of the research on FEL Oscillator’s basic principle, a conceptual design and parameters study of a compact EA-FEL is proposed in this paper. The numerical modeling has been carried out by using 1D FEL stimulation code FELO [6]. BRIEF REVIEW OF THE EA-FEL OSCILLATOR SCHEME In this scheme, electrostatic accelerator generates continuous beams of very high quality electrons and small energy spread. The resonator is of a symmetric nearconcentric design and a collector collects the decelerated electrons. The schematic of this EA-FEL Oscillator is provided in Figure 1. Figure 1: Conceptual design of the EA-FEL Oscillator. Reference to the electron beam parameters of normal electrostatic accelerator and the present technology, we use a 3MeV beam to limit the size of EA tank and apply other electron parameter as in UCSB-FEL. According to the equation of maximum gain of FEL Oscillator, the small signal gain is proportional to the number of periods and on-axis field strength, so we must strike a balance between achieving larger output power and satisfying device miniaturization. The main design parameters for the simulations are listed in Table 1. Table 1: The Main Parameters for EA-FEL Oscillator Electron Beam Beam energy 3 MeV Current 2 A Energy spread 0.01% Emittance 10 mm-mrad Undulator K 0.3 Period length 2 cm Number of periods 50 Optical Cavity Radius of curvature of mirrors 1.08 m Radiation wavelength 303 m  Distance from upstream mirror to undulator centre 1m Optical cavity length 2m ___________________________________________ * Work supported by the Major State Basic Research Development Programme of China under Grant No. 2011CB808301 and the National Nature Science Foundation of China under Grant No. 10975137 # wuailing@mail.ustc.edu.cn Such devices have been developed and operated WEPD51 Proceedings of FEL2012, Nara, Japan ISBN 978-3-95450-123-6 488 C op yr ig ht c ○ 20 12 by th e re sp ec tiv e au th or s THz and Long Wavelength FELs PARAMETER STUDY OF THE EA-FEL OSCILLATOR SCHEME The goals of the EA-FEL Oscillator optimization are maximum net gain and peak output power. Firstly, the influence of electron beam on gain and output power is studied as shown in Figure 2. It is found that when the energy spread is less than 0.02%, the peak output power is considerable, about 5300W. Refer to the energy spreads of electron beam in UCSB FEL, this parameter of beam could be set to 0.01%. As shown in Figure 3, with the increase of beam current, the FEL could grow considerably and the saturation time is reduced. The output powers at different emittance are also simulated and the results indicate the emittance of beam has little influence on the FEL performance. 0.01 0.02 0.03 0.04 0.05 4700 4800 4900 5000 5100 5200 5300