Synthesis of Single-walled Carbon Nanotubes by Using Sputtered Bimetallic catalyst
Shi-ting Wu,Wenjing Xu,Mingchu Zou,Liusi Yang,Huaisheng Wu,Anyuan Cao
2016-01-01
Abstract:2016 PKU-UTokyo Nano-Carbon Summer Camp Synthesis of Single-walled Carbon Nanotubes by Using Sputtered Bimetallic catalyst Hua An, Rong Xiang 1 , Taiki Inoue 1 , Shohei Chiashi 1 , Shigeo Maruyama 1,2 1. Department of Mechanical Engineering, the University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo, 113-8656, Japan 2. Energy NanoEngineering Laboratory, National Institute of Advanced Industrial Science and Technology (AIST), 1-2-1 Namiki, Tsukuba, 305-8564, Japan anhua@photon.t.u-tokyo.ac.jp Ever since their discovery, single-walled carbon nanotubes (SWNTs) have attracted intensive attention because of their special electronic properties and potential applications. Unfortunately, the as-grown SWNTs are always a mixture of various chiralities, which limits their application in nanoelectronics. Since the chirality determines the structure of SWNTs, diameter control and chirality control are the prerequisite to obtain SWNTs with homogeneous properties. Extensive researches have focused on the diameter-control and chirality-control growth of SWNTs. However, it is a critical challenge to grow single-chirality SWNTs. On the other hand, bimetallic catalysts usually possess different catalytic properties than either of their parent metals and thus they have been widely explored in catalytic reactions for SWNTs growth. Recently, we have tried bimetallic catalysts to grow SWNTs by alcohol catalytic chemical vapor deposition (ACCVD). The catalysts were prepared on silicon substrates by a simple magnetron sputtering method. The SWNTs were characterized by scanning electron microscopy (SEM), Raman spectroscopy, optical absorption spectroscopy and transmission electron microscopy (TEM). We have successfully grown SWNTs with small diameter and narrow chirality distribution by detailed parametric study, which paves a possible way to large-scale industrial applications in nanodevices. Self-introduction I am AN Hua, from China. And currently, I am a third-year PhD candidate in the University of Tokyo. My research topic is about the synthesis of single-walled carbon nanotubes. I like all kinds of delicious foods. Hope to make more friends and have fun in Beijing. 2016 PKU-UTokyo Nano-Carbon Summer Camp Carbon Nanotube and Graphene Applications in Solar Cells Clement Delacou, Il Jeon, Mohamed Atwa, Masaki Sota, Yutaka Matsuo, Shigeo Maruyama Maruyama-Chiashi Laboratory, Department of Mechanical Engineering, The University of Tokyo delacou@photon.t.u-tokyo.ac.jp Single-Walled Carbon Nanotubes (SWNTs) and graphene have the superiorities in terms of high electrical conductivity at high transparency, combined with earth abundance and chemical stability, they are supposed to be a very promising candidate for next-generation solar cell applications. In Maruyama-Chiashi laboratory, we use ACCVD (Alcohol Chemical Vapor Deposition) for using Ethanol as carbon source initially to grow SWNTs[1] (Fig.1) and then also for growing graphene[2] (Fig.2). Numerous studies on these parameters in our laboratory have enabled to understand better how those factors affects growth in term of size, amount, morphology and quality of these nanocarbon materials. One application of these nanocarbon materials in solar cell is to replace ITO (Indium Tin Oxide) as transparent electrode in solar cells, because Indium is rare, expensive, fragile and not flexible. But the current challenge here is to create a dense film with both high transparency and high conductivity. References: Fig.1 TEM of SWNTs Fig.2 SEM of large size monocrystalline graphene [1] S. Maruyama, R. Kojima, Y. Miyauchi, S. Chiashi, and M. Kohno, Chem. Phy. Lett., 2002 [2] X. Chen, P. Zhao, R. Xiang, S. Kim, J. Cha, S. Chiashi, S. Maruyama, Carbon, 2015 Self-introduction Birthday: 1990/1/28 (26) Hometown: Saint Plantaire (village in middle-West of France) Education: Technical Textile Engineering Master Degree in ENSAIT (in Roubaix, North of France) Skills: SWNTs and graphene growth, organic solar cell device Type: Kind, emotional, helpful, creative, social, slow Hobbies: Guitar, song writing, anime, work out, tennis, running 2016 PKU-UTokyo Nano-Carbon Summer Camp Experimental investigation of thermal conductivity of single walled carbon nanotube thin film with infrared thermal imager Ya FENG, Taiki INOUE, Rong XIANG, Shohei CHIASHI, Shigeo MARUYAMA Department of Mechanical Engineering, The University of Tokyo, Tokyo 113-8656, Japan Energy NanoEngineering Lab., National Institute of Advanced Industrial Science and Technology, Tsukuba 305-8564, Japan Fengya@photon.t.u-tokyo.ac.jp In theory, single walled carbon nanotubes (SWNT) have been proven to be with extraordinarily high axial thermal conductivity owing to its unique quasi-one-dimensional structure, thus having been expected to mitigate the severe heat dissipation problem in the continuously shrinking electronic devices. In its bulk counterpart form, the ballistic phonon transfer is seriously impeded by the tube-tube interface scattering, but the remarkable thermal conductivity of single SWNT still boost the application of SWNT thin film as a thermal interface material. Therefore, researches are extensively conducted, trying to precisely measure the thermal conductivity of carbon nanotube films grown in laboratory, which still remains quite a difficulty. Therefore, in this work, we proposed a new method to directly measure the thermal conductivity of SWNT thin film. Two cantilevered silicon thin plates (thickness of 100μm) were joined with the SWNT thin film suspended in between, while the fixed ends were respectively bathed in different temperatures to form a steady state heat flow across. With the infrared thermal imager recording the temperature distribution along the targeted structure, the silicon plates with known thermal conductivity can work as a reference to calculate the heat flux transporting through the SWNT thin film. Repeating the experiment without the SWNT thin film, the effect of thermal radiation can be neatly deducted. [1] MS Dresselhaus et al. Adv. Phys. 49 (6), 705-814 (2000). [2] Tong Tao et al. IEEE T Compon. Pack. T 30 (1), 92-100 (2007). Self-introduction My name is Feng Ya, sophomore of doctor course in Mechanical Engineering, the University of Tokyo. I am Chinese, from Hunan Province, once lived in Beijing for three years during my master course at Chinese Academy of Sciences. I am not a sociable person, so I prefer to be left alone and read a book. 2016 PKU-UTokyo Nano-Carbon Summer Camp Study on the friction properties of a-C:H films in a microstructural point of view Takumi Ishikawa, Junho Choi Department of Mechanical engineering ishikawa@sstl.info Hydrogenated amorphous carbon (a-C:H) films have been gathering attention recently for their high hardness, chemical inertness, low friction coefficient and high wear resistance, which enable a-C:H films to be a good coating materials in tribology fields. On the other hand, these properties are greatly influenced by microstructure of a-C:H films, and the microstructure is changed according to coating methods and parameters. In our previous study, Raman spectroscopy was used to clarify the microstructure of a-C:H films, and the microstructure of a-C:H films evaluated by Raman parameters and the mechanical properties of the films were successfully correlated. In this study, The correlation between the microstructure of a-C:H films and their tribological properties was investigated. From the evaluation of the microstructure of a-C:H films using Raman spectroscopy, it was found that the structure of a-C:H films can be classified into three main categories. i.e., polymer-like carbon (PLC), diamond-like carbon (DLC) and graphite-like carbon (GLC) structures. a-C:H films with DLC structure showed the highest friction coefficient among these three carbon structures. Also, the friction coefficient of DLC structured a-C:H film increases in proportion to their hardness. By investigating the friction surface, we found that chemical species generated during friction may be the main reason which affects the friction coefficient. Higher the friction coefficient is, more oxidation species is generated during friction. It is known that the surrounding environment (water, oxygen, etc.) affect the friction performance of a-C:H films dramatically because they can easily react with the surface chemically. Self-introduction I’m 24 years old. My hometown is Aichi prefecture (near Nagoya), but I live in Tokyo now since my university is there. I have lived in Los Angeles when I was a child for four years. Now, I belong to the tribology laboratory, and I’m majoring in friction. I like to play sports, especially, soft tennis and basketball. Also, I like to read books and watch movies. I want to know more about nano carbon material, and its properties, I’m looking forward to this program. 2016 PKU-UTokyo Nano-Carbon Summer Camp Window-like Organic Solar Cells with p-Doped Carbon Nanotube Il Jeon 1 , Clement Delacou 1 , Shigeo Maruyama 1,2 , and Yutaka Matsuo 1 1 Department of Mechanical Engineering, The University of Tokyo, 2 National Institute of Advanced Industrial Science and Technology (AIST) il.jeon@photon.t.u-tokyo.ac.jp Organic solar cells are flexible and inexpensive, and they are expected to have a wide range of applications. In addition, many transparent organic solar cells have been reported and their success hinges on full transparency, high power conversion efficiency, and low-cost fabrication. Recently, carbon nanotubes and graphene, which meet these criteria, have been used in transparent conductive electrodes. However, their use in top electrodes has been limited by mechanical difficulties in fabrication and doping. Here, expensive metal top electrodes were replaced with high-performance, easy-to-transfer, aerosol-synthesized carbon nanotubes to produce transparent organic solar cells. The carbon nanotubes were doped by two methods developed in this work: HNO3 doping via ‘sandwich tran