Syddansk Universitet Ultrathin 90-degree sharp bends for spoof surface plasmon
Yihao Yang,Hongsheng Chen,Sanshui Xiao,N. Asger Mortensen,Jingjing,Zhang
2015-01-01
Abstract:At low frequencies outside the plasmonic range, strongly confined surface waves can be achieved on periodically structured metal surfaces, thereby allowing for the design of compact electromagnetic guiding devices. Here, we propose an approach to realize highly efficient transmission of spoof surface plasmons around 90-degree sharp bends on ultrathin metallic films in the microwave regime. We demonstrate that by judiciously engineering the structure, the dispersion relation can be designed to reduce the scattering. Furthermore, the reflection can be suppressed by proper structural decoration at the bending corner. A onedimensional scattering theory is employed to understand and verify the transmission properties of our waveguide bend structure. Our design scheme is not restricted to the specific structure we propose here but can be applied to other guiding components built up on two dimensional metal surfaces. ©2015 Optical Society of America OCIS codes: (250.5403) Plasmonics; (160.3918) Metamaterials; (240.6690) Surface waves. References and links 1. W. L. Barnes, A. Dereux, and T. W. Ebbesen, “Surface plasmon subwavelength optics,” Nature 424(6950), 824– 830 (2003). 2. W. H. Tsai, Y. C. Tsao, H. Y. Lin, and B. C. Sheu, “Cross-point analysis for a multimode fiber sensor based on surface plasmon resonance,” Opt. Lett. 30(17), 2209–2211 (2005). 3. M. L. Brongersma and V. M. Shalaev, “Applied physics. The case for plasmonics,” Science 328(5977), 440–441 (2010). 4. J. Zhang, S. Xiao, M. Wubs, and N. A. Mortensen, “Surface plasmon wave adapter designed with transformation optics,” ACS Nano 5(6), 4359–4364 (2011). 5. Y. Luo, A. Aubry, and J. B. Pendry, “Electromagnetic contribution to surface-enhanced Raman scattering from rough metal surfaces: a transformation optics approach,” Phys. Rev. B 83(15), 155422 (2011). 6. Y. Luo, J. B. Pendry, and A. Aubry, “Surface plasmons and singularities,” Nano Lett. 10(10), 4186–4191 (2010). 7. P. Andrew, S. C. Kitson, and W. L. Barnes, “Surface-plasmon energy gaps and photoabsorption,” J. Mod. Opt. 44(2), 395–406 (1997). 8. J. L. Coutaz, M. Neviere, E. Pic, and R. Reinisch, “Experimental study of surface-enhanced second-harmonic generation on silver gratings,” Phys. Rev. B Condens. Matter 32(4), 2227–2232 (1985). 9. Y. Luo, D. Y. Lei, S. A. Maier, and J. B. Pendry, “Broadband light harvesting nanostructures robust to edge bluntness,” Phys. Rev. Lett. 108(2), 023901 (2012). 10. J. B. Pendry, A. I. Fernandez-Dominguez, Y. Luo, and R. Zhao, “Capturing photons with transformation optics,” Nat. Phys. 9(8), 518–522 (2013). 11. Y. Luo, D. Y. Lei, S. A. Maier, and J. B. Pendry, “Transformation-optics description of plasmonic nanostructures containing blunt edges/corners: from symmetric to asymmetric edge rounding,” ACS Nano 6(7), 6492–6506 (2012). 12. J. B. Pendry, Y. Luo, and R. Zhao, “Transforming the optical landscape,” Science 348(6234), 521–524 (2015). 13. Y. Luo, R. Zhao, and J. B. Pendry, “van der Waals interactions at the nanoscale: the effects of nonlocality,” Proc. Natl. Acad. Sci. U.S.A. 111(52), 18422–18427 (2014). 14. J. B. Pendry, L. Martín-Moreno, and F. J. Garcia-Vidal, “Mimicking surface plasmons with structured surfaces,” Science 305(5685), 847–848 (2004). #241242 Received 18 May 2015; revised 29 Jun 2015; accepted 13 Jul 2015; published 15 Jul 2015 © 2015 OSA 27 Jul 2015 | Vol. 23, No. 15 | DOI:10.1364/OE.23.019074 | OPTICS EXPRESS 19074 15. J. J. Wood, L. A. Tomlinson, O. Hess, S. A. Maier, and A. I. Fernández-Domínguez, “Spoof plasmon polaritons in slanted geometries,” Phys. Rev. B 85(7), 075441 (2012). 16. F. J. Garcia-Vidal, L. Martin-Moreno, and J. B. Pendry, “Surfaces with holes in them: new plasmonic metamaterials,” J. Opt. A, Pure Appl. Opt. 7(2), S97–S101 (2005). 17. D. Martin-Cano, M. L. Nesterov, A. I. Fernandez-Dominguez, F. J. Garcia-Vidal, L. Martin-Moreno, and E. Moreno, “Domino plasmons for subwavelength terahertz circuitry,” Opt. Express 18(2), 754–764 (2010). 18. Y. G. Ma, L. Lan, S. M. Zhong, and C. K. Ong, “Experimental demonstration of subwavelength domino plasmon devices for compact high-frequency circuit,” Opt. Express 19(22), 21189–21198 (2011). 19. A. I. Fernández-Domínguez, L. Martín-Moreno, F. J. García-Vidal, S. R. Andrews, and S. A. Maier, “Spoof surface plasmon polariton modes propagating along periodically corrugated wires,” IEEE. J. Sel. Top. Quantum Electron. 14(6), 1515–1521 (2008). 20. S. A. Maier, S. R. Andrews, L. Martín-Moreno, and F. J. García-Vidal, “Terahertz surface plasmon-polariton propagation and focusing on periodically corrugated metal wires,” Phys. Rev. Lett. 97(17), 176805 (2006). 21. M. Navarro-Cía, M. Beruete, S. Agrafiotis, F. Falcone, M. Sorolla, and S. A. Maier, “Broadband spoof plasmons and subwavelength electromagnetic energy confinement on ultrathin metafilms,” Opt. Express 17(20), 18184– 18195 (2009). 22. X. Shen, T. J. Cui, D. Martin-Cano, and F. J. Garcia-Vidal, “Conformal surface plasmons propagating on ultrathin and flexible films,” Proc. Natl. Acad. Sci. U.S.A. 110(1), 40–45 (2013). 23. Z. Liao, Y. Luo, A. I. Fernández-Domínguez, X. Shen, S. A. Maier, and T. J. Cui, “High-order localized spoof surface plasmon resonances and experimental verifications,” Sci. Rep. 5, 9590 (2015). 24. H. C. Zhang, S. Liu, X. Shen, L. H. Chen, L. Li, and T. J. Cui, “Broadband amplification of spoof surface plasmon polaritons at microwave frequencies,” Laser Photonics Rev. 9(1), 83–90 (2015). 25. X. Wan, X. Shen, Y. Luo, and T. J. Cui, “Planar bifunctional Luneburg-fisheye lens made of an anisotropic metasurface,” Laser Photonics Rev. 8(5), 757–765 (2014). 26. J. J. Xu, H. C. Zhang, Q. Zhang, and T. J. Cui, “Efficient conversion of surface-plasmon-like modes to spatial radiated modes,” Appl. Phys. Lett. 106(2), 021102 (2015). 27. H. F. Ma, X. P. Shen, Q. Cheng, W. X. Jiang, and T. J. Cui, “Broadband and high-efficiency conversion from guided waves to spoof surface plasmon polaritons,” Laser Photonics Rev. 8(1), 146–151 (2014). 28. B. Ng, J. Wu, S. M. Hanham, A. I. Fernándezu-Domínguez, N. Klein, Y. F. Liew, M. B. Breese, M. Hong, and S. A. Maier, “Spoof plasmon surfaces: a novel platform for THz sensing,” Adv. Opt. Mater. 1(8), 543–548 (2013). 29. Z. Liao, X. Shen, B. C. Pan, J. Zhao, Y. Luo, and T. J. Cui, “Combined system for efficient excitation and capture of LSP resonances and flexible control of SPP transmissions,” ACS Photonics 2(6), 738–743 (2015). 30. N. Yu, Q. J. Wang, M. A. Kats, J. A. Fan, S. P. Khanna, L. Li, A. G. Davies, E. H. Linfield, and F. Capasso, “Designer spoof surface plasmon structures collimate terahertz laser beams,” Nat. Mater. 9(9), 730–735 (2010). 31. Y. Liu, H. Shi, C. Wang, C. Du, and X. Luo, “Multiple directional beaming effect of metallic subwavelength slit surrounded by periodically corrugated grooves,” Opt. Express 16(7), 4487–4493 (2008). 32. T. Jiang, L. Shen, J. J. Wu, T. J. Yang, Z. Ruan, and L. Ran, “Realization of tightly confined channel plasmon polaritons at low frequencies,” Appl. Phys. Lett. 99(26), 261103 (2011). 33. W. Zhu, A. Agrawal, and A. Nahata, “Planar plasmonic terahertz guided-wave devices,” Opt. Express 16(9), 6216–6226 (2008). 34. A. I. Fernández-Domínguez, E. Moreno, L. Martin-Moreno, and F. J. Garcia-Vidal, “Guiding terahertz waves along subwavelength channels,” Phys. Rev. B 79(23), 233104 (2009). 35. K. J. Kim, J. E. Kim, H. Y. Park, Y. H. Lee, S. H. Kim, S. G. Lee, and C. S. Kee, “Propagation of spoof surface plasmon on metallic square lattice: bending and splitting of self-collimated beams,” Opt. Express 22(4), 4050– 4058 (2014). 36. A. Mekis, J. C. Chen, I. Kurland, S. Fan, P. R. Villeneuve, and J. D. Joannopoulos, “High transmission through sharp bends in photonic crystal waveguides,” Phys. Rev. Lett. 77(18), 3787–3790 (1996). 37. C. L. C. Smith, N. Stenger, A. Kristensen, N. A. Mortensen, and S. I. Bozhevolnyi, “Gap and channeled plasmons in tapered grooves: a review,” Nanoscale 7(21), 9355–9386 (2015).
What problem does this paper attempt to address?
-
Broadband Nonreciprocal Spoof Plasmonic Phase Shifter Based on Transverse Faraday Effects
Hao Yan,Liqiao Jing,Jia Zhao,Chuanning Niu,Yujie Zhang,Liuge Du,Zuojia Wang
DOI: https://doi.org/10.1364/oe.462863
IF: 3.8
2022-01-01
Optics Express
Abstract:Spoof surface plasmon polaritons (SSPPs) have aroused widespread concern due to their strong ability in field confinement at low frequencies. For miniaturized integrated circuits, there is a pressing need for nonreciprocal spoof plasmonic platforms that provide diode functionalities. In this letter, we report the realization of nonreciprocal phase shifting in SSPPs using the transverse Faraday effect. A plasmonic coupled line is constructed by flipped stacking two corrugated metallic strips, in order to enhance the mode coupling between evanescent waves that carry opposite transverse spin angular momenta. With a transverse magnetized ferrite cladding, the SSPP mode is split into two circularly-polarized ones that show different propagation constants over a broad band. A nonreciprocal phase shifter compatible to standard microstrips is designed to validate the breaking of time-reversal symmetry in SSPPs. Microwave measurement demonstrates a differential phase shift up to 46.2 degrees/cm from 12 GHz to 15 GHz. Owing to the advantages of strong field confinement and contactless ferrite integration, the proposed method enables an alternative pathway for nonreciprocal spoof interconnects. (C) 2022 Optica Publishing Group under the terms of the Optica Open Access Publishing Agreement
-
Ultrathin 90-Degree Sharp Bends for Spoof Surface Plasmon Polaritons
Yihao Yang,Hongsheng Chen,Sanshui Xiao,N. Asger Mortensen,Jingjing Zhang
DOI: https://doi.org/10.1364/oe.23.019074
IF: 3.8
2015-01-01
Optics Express
Abstract:At low frequencies outside the plasmonic range, strongly confined surface waves can be achieved on periodically structured metal surfaces, thereby allowing for the design of compact electromagnetic guiding devices. Here, we propose an approach to realize highly efficient transmission of spoof surface plasmons around 90-degree sharp bends on ultrathin metallic films in the microwave regime. We demonstrate that by judiciously engineering the structure, the dispersion relation can be designed to reduce the scattering. Furthermore, the reflection can be suppressed by proper structural decoration at the bending corner. A one-dimensional scattering theory is employed to understand and verify the transmission properties of our waveguide bend structure. Our design scheme is not restricted to the specific structure we propose here but can be applied to other guiding components built up on two dimensional metal surfaces.
-
Spoof surface plasmon photonics
Francisco J. Garcia-Vidal,Antonio I. Fernández-Domínguez,Luis Martin-Moreno,Hao Chi Zhang,Wenxuan Tang,Ruwen Peng,Tie Jun Cui
DOI: https://doi.org/10.1103/revmodphys.94.025004
IF: 50.485
2022-05-21
Reviews of Modern Physics
Abstract:In undergraduate courses on classical electromagnetism, it is taught that a perfect conductor expels the electromagnetic (EM) field, and hence its surface is not able to support the propagation of bound EM waves. However, when the surface of a perfect conductor is structured at a length scale much smaller than the operating wavelength, geometrically induced surface EM modes can be supported. Owing to their similarities with the surface plasmon polaritons (SPPs) in the optical regime, these surface EM modes were named spoof surface plasmons. The concept of spoof surface plasmons has opened up a new line of research within plasmonics with the aim of transferring all the potentialities of SPPs in the optical regime to lower frequencies (microwave, terahertz, and midinfrared regimes) in which a metal behaves as a quasiperfect conductor. In recent years, several research groups have extended this concept from planar surfaces to waveguides, and eventually to resonators, covering the entire range of structures studied in standard plasmonics. This review provides a detailed perspective on the recent developments in spoof surface plasmon photonics from both the fundamental and applied sides. https://doi.org/10.1103/RevModPhys.94.025004 © 2022 American Physical Society
physics, multidisciplinary
-
High-order modes of spoof surface plasmonic wave transmission on thin metal film structure.
Xiaoyong Liu,Yijun Feng,Bo Zhu,Junming Zhao,Tian Jiang
DOI: https://doi.org/10.1364/OE.21.031155
IF: 3.8
2013-01-01
Optics Express
Abstract:Recently, conformal surface plasmon (CSP) structure has been successfully proposed that could support spoof surface plasmon polaritons (SPPs) on corrugated metallic strip with ultrathin thickness [Proc. Natl. Acad. Sci. U.S.A. 110, 40-45 (2013)]. Such concept provides a flexible, conformal, and ultrathin wave-guiding element, very promising for application of plasmonic devices, and circuits in the frequency ranging from microwave to mid-infrared. In this work, we investigated the dispersions and field patterns of high-order modes of spoof SPPs along CSP structure of thin metal film with corrugated edge of periodic array of grooves, and carried out direct measurement on the transmission spectrum of multi-band of surface wave propagation at microwave frequency. It is found that the mode number and mode bands are mainly determined by the depth of the grooves, providing a way to control the multi-band transmission spectrum. We have also experimentally verified the high-order mode spoof SPPs propagation on curved CSP structure with acceptable bending loss. The multi-band propagation of spoof surface wave is believed to be applicable for further design of novel planar devices such as filters, resonators, and couplers, and the concept can be extended to terahertz frequency range. (C) 2013 Optical Society of America
-
Spoof surface plasmons on ultrathin corrugated metal structures in microwave and terahertz frequencies
T. Cui,Xiaopeng Shen
DOI: https://doi.org/10.1109/METAMATERIALS.2013.6809111
2013-09-01
Metamaterials
Abstract:Structured metal surfaces can support spoof surface plasmons (SPs) in the microwave and terahertz frequencies, opening up a new road to manipulate the surface electromagnetic waves in subwavelength scales. The strong field confinements and fantastic plasmonic effects have motivated a vast range of studies and applications. However, the existing spoof SP structures are difficult to be integrated due to the nonplanar features. In this presentation we will review our recent work on the spoof SPs on ultrathin textured metallic surfaces, including the printed planar surface plasmon polaritons (SPPs) and conformal SPPs propagating on ultrathin corrugated metallic strips, and the spoof multipolar localized SPs on ultrathin textured metallic disks. We show that the proposed designs are versatile and flexible to route and localize SPs by numerical simulations and experiments. Hence the proposed ultrathin textured metallic structures have potential applications in building plasmonic components and sensors in the microwave and terahertz frequencies.
Materials Science,Physics
-
Hyperbolic Spoof Plasmonic Metasurfaces
Yihao Yang,Liqiao Jing,Lian Shen,Zuojia Wang,Bin Zheng,Huaping Wang,Erping Li,Nian-Hai Shen,Thomas Koschny,Costas M Soukoulis,Hongsheng Chen
DOI: https://doi.org/10.1038/am.2017.158
IF: 10.761
2017-01-01
NPG Asia Materials
Abstract:Hyperbolic metasurfaces have recently emerged as a new research frontier because of the unprecedented capabilities to manipulate surface plasmon polaritons (SPPs) and many potential applications. However, thus far, the existence of hyperbolic metasurfaces has neither been observed nor predicted at low frequencies because noble metals cannot support SPPs at longer wavelengths. Here, we propose and experimentally demonstrate spoof plasmonic metasurfaces with a hyperbolic dispersion, where the spoof SPPs propagate on complementary H-shaped, perfectly conducting surfaces at low frequencies. Thus, non-divergent diffractions, negative refraction and dispersion-dependent spin-momentum locking are observed as the spoof SPPs travel over the hyperbolic spoof plasmonic metasurfaces (HSPMs). The HSPMs provide fundamental new platforms to explore the propagation and spin of spoof SPPs. They show great capabilities for designing advanced surface wave devices such as spatial multiplexers, focusing and imaging devices, planar hyperlenses, and dispersion-dependent directional couplers, at both microwave and terahertz frequencies.
-
High-efficiency Chirality-Modulated Spoof Surface Plasmon Meta-Coupler
Jingwen Duan,Huijie Guo,Shaohua Dong,Tong Cai,Weijie Luo,Zhongzhu Liang,Qiong He,Lei Zhou,Shulin Sun
DOI: https://doi.org/10.1038/s41598-017-01664-w
IF: 4.6
2017-01-01
Scientific Reports
Abstract:Efficiently exciting surface plasmon polaritons (SPP) is highly desired in many photonic applications, but most approaches (such as prism and grating couplers) cannot control flexibly their SPP excitation directions. While Pancharatnam-Berry (PB) metasurfaces were recently proposed to achieve direction-controllable SPP excitations, such scheme suffers from low-efficiency issue due to both direct reflections at the coupler surface and the mode mismatch between the coupler and the guiding-out plasmonic structure. In this article, we solve these issues via imposing two criterions to guide design both the metasurface and the plasmonic metal, based on which a direction-controllable SPP excitation with very high efficiency can be realized. As a proof of concept, we designed/fabricated a realistic device working in the microwave regime, and performed both near-field and far-field measurements to demonstrate that it can achieve an spoof SPP conversion efficiency ~78%, much higher than previous devices. Full-wave simulations are in good agreement with experiments, showing that the efficiency can be further pushed to 92% with optimized designs. Our findings can stimulate spoof SPP-related applications, particularly can help enhance the spin-dependent light-matter interactions in low frequency regime.
-
Spoof Surface Plasmons Dispersion and Modes of a Lamellar Grating for Terahertz Applications
Yong-Qiang Liu,Ling-Bao Kong,Pu-Kun Liu
DOI: https://doi.org/10.1109/ursi-at-rasc.2015.7303035
2015-01-01
Abstract:This abstract presents a complete study of dispersion and mode distribution of spoof surface plasmons (SSPs) in planar metal gratings. The subject under investigation is intended for Terahertz wave generation. Because of its characteristics of near field localization of this plasmonic wave and collective resonance effects of electrons in metals, SSPs in this textured metal surface has attracted enormous interest such as potential applications in plasmonic metamaterials (F. J. García-Vidal. et al., J. Opt. A: Pure Appl. Opt, 7, 2005, S97–S101). There are many novel phenomena steam from surface plasmons, such as enhanced total reflection (G. A. Plotz. et al., J. Opt. Soc. Am., 69, 1979, pp.419–422), extraordinary optical transmission (T. W. Ebbesen. et al., Nature, 391, 1998, pp. 667–669), enhanced Raman spectroscopy (P. L. Stiles. et al., Ann. Rev. Chem. 1, 2008, pp. 601–626), superradiant Terahertz Smith-Purcell radiation (Y. M. Shin. et al., Appl. Phys. Lett. 90, 2007, pp. 031502), etc.
-
Electromagnetic Wave Dispersion Curve Computation for Quasi-1D Spoof Surface Plasmon Polaritons
Jiefeng Zhou,Ling Zhang,Da Li,Er-Ping Li
DOI: https://doi.org/10.1109/aces-china62474.2024.10699947
2024-01-01
Abstract:The quasi-one-dimensional (quasi-1D) spoof surface plasmon polariton (SSPP) provides a new route for optically transparent electronic devices. The dispersion curves can control the electromagnetic wave propagation characteristics of the quasi-1D SSPP by manipulating the geometric parameters. However, the dispersion curves of quasi-1D SSPP have not been analytically derived and thoroughly studied. This paper derives the dispersion curves of the quasi-1D SSPP using equivalent permittivity and permeability methods, which can accurately predict the relationship between wave number and its geometric parameters. The simulation results validate the proposed dispersion curves. Based on the dispersion curves, this paper further presents a broadband optically transparent transmission line, which can achieve high-efficiency transmission from 3.0 to 14.4 GHz.
-
Coplanar Excitation of Terahertz Spoof Surface Plasmon and High-Q Sensing
De-xian Yan,Gang Cheng,Er-ping Li,Xiang-jun Li,Xue-ru Zhang,Yi-lin Wu
DOI: https://doi.org/10.37188/co.2022-0204
IF: 1.1
2023-01-01
Chinese Optics
Abstract:In this paper, the coplanar excitation of terahertz Spoof Surface Plasmon (SSP) realized by using a single-layer grating meta-surface coupling method is proposed, which overcomes the disadvantages such as the reflection measurement when applying the medium couplers. The periodic grating and terahertz SSP composite structure are simultaneously constructed on the monolayer metal structure. When the terahertz waves are incident vertically, the wave vector of grating structures and the wave vector of SSPs are matched, and the SSP mode can be excited. The high Q value resonant peaks can be generated in the transmission spectrum, and the Q factor can reach 1 923. The effects of the structural parameters on the grating-coupled meta -surface transmission spectrum and dispersion characteristics are also analyzed. In addition, based on the high Q resonant peak in the transmission spectrum of the designed structure, the high sensing sensitivity is about 67 GHz/RIU at the resonant center frequency of 0.22 THz. The structure proposed in this paper, which realizes terahertz SSP excitation and high Q sensing by treating a single-layer meta-surface structure, exhibits great application potential in many practical applications.
-
Band Rejection Filter Based on A Composite Spoof Surface Plasmon Periodic Structure
Michael Chisala,Jing Zhou,Dong Yang,Lin Hai
DOI: https://doi.org/10.1109/apcap.2017.8420666
2017-01-01
Abstract:Research has demonstrated how the interaction between electromagnetic fields and specially tailored sub wavelength metallic structures leads to unique properties such as strong confinement of electromagnetic fields and backward wave propagation. Various designs of surface plasmon (SP) propagation wave-guides in the microwave and terahertz frequency regime employing corrugated ultra-thin periodic metallic unit structures have been reported, however SP wave guides employing a combination of different unit cells have not been experimentally demonstrated to the best of our knowledge. In this paper, we propose a novel composite HO2-type ultrathin metallic structure to produce a band-stop spoof SP (SSP) based filter. The proposed structure's SSP wave guide is composed of periodic H and slot-type unit cell structures. The SSP structure is fed from a CPW transmission line through a transition matching structure composed of gradient corrugated grooves and Vivaldi curves to match both the wave number and impedance of the SSP wave guide. Simulation results show excellent band stop filtering performance of the proposed design. In addition, the dispersion analysis of the proposed composite wave guide revealed that the proposed SSP waveguide can support backward wave propagation of surface plasmons. With such unique properties the proposed composite SSP wave-guide has potential in new applications of plasmonic meta-material in integrated microwave circuits.
-
Manipulating Surface Plasmon Waves by Transformation Optics: Design Examples of A Beam Squeezer, Bend, and Omnidirectional Absorber
Yu Zhen-Zhong,Feng Yi-Jun,Wang Zheng-Bin,Zhao Jun-Ming,Jiang Tian
DOI: https://doi.org/10.1088/1674-1056/22/3/034102
2013-01-01
Chinese Physics B
Abstract:We present several design examples of how to apply transformation optics and curved space under coordinate transformation to manipulating the surface plasmon waves in a controlled manner. We demonstrate in detail the design procedure of the plasmonic wave squeezer, in-plane bend and omnidirectional absorber. We show that the approximation method of modifying only the dielectric material of a dielectric-metal surface of the plasmonic device could lead to acceptable performance, which facilitates the fabrication of the device. The functionality of the proposed plasmonic device is verified using three-dimensional full-wave electromagnetic simulations. Aiming at practical realization, we also show the design of a plasmonic in-plane bend and omnidirectional absorber by an alternative transformation scheme, which results in a simple device structure with a tapered isotropic dielectric cladding layer on the top of the metal surface that can be fabricated with existing nanotechnology.
-
Ultrathin metasurface with topological transition for manipulating spoof surface plasmon polaritons
Yihao Yang,Lian Shen,Liqiao Jing,Zheping Shao,Thomas Koschny,Costas M. Soukoulis,Hongsheng Chen
2016-01-01
Abstract: Metasurfaces, with intrinsically planar nature and subwavelength thickness, provide us unconventional methodologies to not only mold the flow of propagating waves but also manipulate near-field waves. Plasmonic metasurfaces with topological transition for controlling surface plasmon polaritons (SPPs) recently have been experimentally demonstrated, which, however, are limited to optical frequencies. In this work, we proposed and experimentally characterized an ultrathin metasurface with the topological transition for manipulating spoof SPPs at low frequency. We demonstrated rich interesting phenomena based on this metasurface, including frequency-dependent spatial localization, non-diffraction propagation, negative refraction, and dispersion-dependent spin-momentum locking of spoof SPPs. Comparing with traditional three-dimensional metamaterials, our metasurface exhibits low propagation loss and compatibility with the photonic integrated circuit, which may find plenty of applications in spatial multiplexers, focusing and imaging devices, planar hyperlens, and dispersion-dependent directional couplers, in microwave and terahertz frequencies.
-
Spoof Surface Plasmonic Graphene for Controlling the Transports and Emissions of Electromagnetic Waves
Pengfei Qin,Er-Ping Li,Yihao Yang,Hanzhi Ma,Bin Zheng,Fei Gao,Zuojia Wang,Lian Shen,Ran Hao,Lay Kee Ang,Hongsheng Chen
DOI: https://doi.org/10.1109/tmtt.2018.2874253
IF: 4.3
2019-01-01
IEEE Transactions on Microwave Theory and Techniques
Abstract:Inspired by the recent development of graphene, we propose and experimentally demonstrate a novel metasurface, namely, spoof surface plasmonic graphene, for controlling the transports and emissions of electromagnetic waves. Similar to graphene, at the corners of the Brillouin zone for our designed metasurface, two bands of spoof surface plasmon polaritons (SSPPs) linearly touch together, forming Dirac-like cones. In the experiments, we directly observed the Dirac cones in the momentum space by using near-field scanning. When the frequency is changed from the lower cone to the Dirac point and to the upper cone, the corresponding SSPPs' transport on the metasurface shows negative group velocities, pseudodiffusion characteristics, and positive group velocities, respectively. The emission of the SSPPs to the air shows a transition of the wavefront from a concave to flat and finally to convex. The metasurface proposed here may find many potential applications in directional antennas, waveguide, diffusion-like transport, focusing and imaging devices, and integrated spoof plasmonic circuits.
-
Terahertz spoof surface plasmon polariton gradient index lens
Shenghao Gu,Xinyao Yuan,Lei Liu,Mingming Sun,Ying Zhang,Quan Xu,Jiaguang Han,Jiaguang Han,Shenghao Gu,Xinyao Yuan,Lei Liu,Mingming Sun,Ying Zhang,Quan Xu,Jiaguang Han
DOI: https://doi.org/10.1016/j.rinp.2023.106332
IF: 4.565
2023-04-01
Results in Physics
Abstract:Plasmonics takes advantage of surface plasmon polaritons (SPPs), which have the characteristics of strong subwavelength field confinement and enhancement. Plasmonic devices that confine light in regions with dimensions that are smaller than the wavelength have important application prospects in on-chip integrated circuits. Nonetheless, at terahertz frequencies, the weak confinement of SPPs and immature near-field technology hinder the development of related devices. Here, a highly confined SPP mode (spoof SPP) is implemented by structuring metal surfaces. Gradient index lenses with variable indices are constructed by fine-tuning the size of the pillars, and the characteristics of several different lenses are examined and explored by scanning near-field terahertz microscopy. Thus, terahertz waves are regulated and more possibilities are provided for further miniaturization and compactness of THz devices.
physics, multidisciplinary,materials science
-
Realization of broadband coherent perfect absorption of spoof surface plasmon polaritons
Cong Wang,Xian Shen,Hongchen Chu,Jie Luo,Xiaoxi Zhou,Bo Hou,Ruwen Peng,Mu Wang,Yun Lai
DOI: https://doi.org/10.1063/5.0089065
IF: 4
2022-04-25
Applied Physics Letters
Abstract:In this work, we propose and demonstrate a scheme to realize broadband coherent perfect absorption of spoof surface plasmon polaritons (SPPs) using an ultrathin conductive film vertically placed on a plasmonic metasurface that supports spoof SPPs. When the conductive film possesses an appropriate sheet resistance, two incident coherent beams of spoof SPP waves can be simultaneously absorbed over a broad spectrum. By tuning the phase difference between the two incident beams from 0 to [Formula: see text], the absorption can be gradually changed from near-100% to near-zero, as verified in full-wave simulations and microwave experiments. Our work extends the theory of coherent perfect absorption from propagating waves to spoof SPPs with a significant advantage of broad working bandwidth.
physics, applied
-
High-Efficiency Directional Excitation of Spoof Surface Plasmon Under Arbitrary Illumination
Li-Zheng Yin,Feng-Yuan Han,Jin Zhao,Yi-Dong Wang,Di Wang,Tie-Jun Huang,Pu-Kun Liu
DOI: https://doi.org/10.1109/lawp.2021.3075534
IF: 4.2
2021-07-01
IEEE Antennas and Wireless Propagation Letters
Abstract:Recent advances in spoof surface plasmon (SSP) have offered enormous opportunities for engineering electromagnetic waves at the subwavelength scale. However, the fundamental limitation of the extremely finite space channels on exciting SSP challenges their practical applications. Here, to the best of our knowledge, a new method that can realize high-efficiency infinite-channel SSP excitation based on hyperbolic plasmonic metasurfaces is proposed. Free-space propagating waves impinging from arbitrary directions can be coupled to SSP owing to the theoretical perfect wave vector match between the modulated incident waves and the hyperbolic plasmonic metasurfaces. A proof-of-method metacoupler working at 8 GHz is designed and fabricated with the novel functionality numerically and experimentally verified by the consistent guide wavelength with theory. Further experimental investigation reveals a total coupling efficiency exceeding 50% for the impinging waves with incidence angles ranging from −44° to 44°. The proposed methodology provides a new route to design multichannel antennas and detectors.
telecommunications,engineering, electrical & electronic
-
Plasmonics: Manipulating Light at the Subwavelength Scale
Cheng-Ping Huang,Yong-Yuan Zhu
DOI: https://doi.org/10.1155/2007/30946
2007-01-01
Active and Passive Electronic Components
Abstract:The coupling of light to collective oscillation of electrons on the metal surface allows the creation of surface plasmon-polariton wave. This surface wave is of central interest in the field of plasmonics. In this paper, we will present a brief review of this field, focusing on the plasmonic waveguide and plasmonic transmission. In the plasmonic waveguide, the light can be guided along the metal surface with subwavelength lateral dimensions, enabling the possibility of high-density integration of the optical elements. On the other hand, in the plasmonic transmission, the propagation of light through a metal surface can be tailored with the subwavelength holes, leading to the anomalous transmission behaviors which have received extensive investigations in recent years. In addition, as a supplement to plasmonics in the visible and near-infrared region, the study of THz plasmonics has also been discussed.
-
Highly-Confined and Low-Loss Spoof Surface Plasmon Polaritons Structure with Periodic Loading of Trapezoidal Grooves
Xiaoyong Liu,Lei Zhu,Qiongsen Wu,Yijun Feng
DOI: https://doi.org/10.1063/1.4926770
IF: 1.697
2015-01-01
AIP Advances
Abstract:In this paper, we propose an ultra-thin spoof surface plasmon polaritons (SPPs) structure, periodically loaded with trapezoidal grooves. Compared to the reported SPPs with rectangular grooves, the proposed SPPs structure can support the guided surface SPP wave with enlarged propagation constant, which implies an enhanced confinement of surface wave along the spoof SPPs structure. Guided-wave characteristics of the proposed SPPs structure are theoretically investigated by virtue of a numerical short-open calibration (SOC) technique. The results show that the loss of spoof SPPs is lower than that in other reported spoof SPPs structures. Experiment on prototype in microwave frequency regime is carried out which validates the theoretical findings. It is believed that the proposed structure could be scaled to THz frequencies, and is very promising in developing the miniaturized planar surface plasmonic devices and circuitry.
-
Terahertz Surface Plasmon Polaritons on A Periodically Structured Metal Film with High Confinement and Low Loss
X. F. Zhang,L. F. Shen,J. -J. Wu,T. -J. Yang
2009-01-01
Journal of Electromagnetic Waves and Applications
Abstract:Spoof surface plasmon polaritons (SPPs) on a real metal film with periodic cut-through slits are investigated theoretically at terahertz frequencies. For both symmetric and antisymmetric modes of spoof SPPs on the film, the propagation length is severely limited by the absorbing loss in the metal when the fields are highly confined. By stuffing the slits with dielectric slabs thicker than the film, the propagation length of spoof SPPs is greatly increased under the subwavelength field confinement, especially for the antisymmetric mode. This improvement of the modal behavior is explained physically.