Abstract:The dynamic characteristics of a continuous rigid-frame bridge with fabricated super-high piers (CRFB-FSP) connected by grouting sleeves and adjacent continuous beam bridges (AB) are significantly different, and they are prone to pounding under earthquake excitation. At present, the pounding response between the CRFB-FSP and AB is still unclear, and the impact of the pounding on the seismic performance of a CRFB-FSP is still in the exploratory stage. In this study, two 1/20 scaled models of a CRFB-FSP (MB) and a cast-in-place AB were designed and manufactured. Then, according to the research purpose and the output performance of the shaking table, three each of non-long-period (NLP) ground motions and near-fault pulse-type (NFPT) ground motions were selected as the inputs of the excitation shaking table test. The peak ground acceleration (PGA) changes from 0.5 g to 1.5 g. According to the similarity ratio (1/20), the initial gap between the MB and AB was taken as 7 mm (prototype design: 140 mm). Furthermore, the longitudinal pounding response between the CFRB-FSP and AB, as well as its influence on the seismic performance of the CFRB-FSP, was systematically investigated through a shaking table test and finite element analysis (FEA). The results showed that the pounding with the CRFB-FSP easily caused a persistent pounding, which may increase the damage risk of the pier. The peak pounding force under the NFPT ground motion was more significant than under the NLP ground motion, whereas the pounding number under the NFPT ground motion was smaller. The peak pounding force increased with the increase in the initial gap, pounding stiffness, span, and pier height. With and without pounding, the CRFB-FSP reflected higher-order mode participation (HMP) characteristics. After pounding, under the NFPT excitation, the HMP contribution increased significantly compared with that of the without pounding condition, while this effect under the NLP excitation was smaller. The peak displacement of the main beam of the CRFB-FSP increased with the increase in the main beam span, pier height and initial gap. The peak bending moment of the pier bottom increased with the increase in the main beam span and initial gap, however, decreased with the increase in the pier height. Moreover, the peak displacement of the main beam and the peak moment of the pier bottom of the CRFB-FSP both reduced. In contrast, the corresponding seismic response of the AB increased under the same conditions.

Pounding-Induced Stress Wave Analysis and Mitigation of Highway Bridges Under Earthquakes

An Analysis of Pounding Mitigation and Stress Waves in Highway Bridges with Shape Memory Alloy Pseudo-Rubber Shock-Absorbing Devices

Stochastic seismic responses analysis of long-span rigid-framed bridge with high piers considering travelling wave effect

Dynamic and Mitigation Analysis of Seismic Pounding Effect on Multi-Span Highway Bridges Subjected to Spatial Earthquakes

Experimental and Analytical Study on Pounding Reduction of Base‐isolated Highway Bridges Using MR Dampers

Point-To-Surface Pounding of Highway Bridges with Deck Rotation Subjected to Bi-Directional Earthquake Excitations

Highway bridge unseating and reduction analysis using SMA restrainers under earthquake excitations

Application of the Endurance Time Method to the Seismic Analysis and Evaluation of Highway Bridges Considering Pounding Effects

Pounding analysis methods and control of highway bridges under seismic excitations

Pounding Reduction of Highway Bridges with Pounding Effect by Using Magnetorheological Dampers Under Earthquake Excitations

Semi-Active Control Of Highway Bridges With Pounding Effect By Using Magnetorheological Dampers Under Earthquake Excitations - Art. No. 642310

Research on the Pounding Response and Pounding Effect of a Continuous Rigid-Frame Bridge with Fabricated Super-High Piers Connected by Grouting Sleeves

Probabilistic Pounding Analysis of High-Pier Continuous Rigid Frame Bridge with Actual Site Conditions

A Phenomenological Contact-Element Model Considering Slight Non-Uniform Contact for Pounding Analysis of Highway Bridges under Seismic Excitations

Seismic Study of an Isolated Cable-Stayed Bridge under Near-Fault Ground Motions

Shaking Table Test on Seismic Performance of Continuous Rigid Frame Bridge with Cast-in-place and Fabricated Super High Piers

Stochastic Seismic Response Analysis of Long-span Continuous Rigid Frame Bridge

Experimental study of a highway bridge with shape memory alloy restrainers focusing on the mitigation of unseating and pounding

SEISMIC DESIGN METHOD OF SMALL AND MEDIUM SPAN BRIDGE CONSIDERING BEARING FRICTION SLIPPING

Study on Semi-Active Control of Highway Bridge Pounding under Seismic Excitations

3d Impact Model Of Highway Bridge During Seismic Events