Abstract:The simultaneous application of new low-NOx emissions standards and greenhouse gas (GHG) rules has placed great pressure on the commercial vehicle industry and has driven demand for innovative solutions. One potential solution, gasoline compression ignition (GCI), utilizes gasoline’s lower reactivity to promote partially premixed combustion and extract efficiency while reducing the PM-NOx trade-off curve. Gasoline’s volatility allows for the use of higher levels of exhaust gas recirculation (EGR), a key enabler of GCI combustion. In order to deliver higher levels of EGR while maintaining sufficient boost pressure, a tailored and efficient air-handling system is critical. This work presents the analysis-led development of a low-NOx GCI air-handling system including both turbocharger matching and EGR configuration for a prototype heavy-duty GCI engine based on a model year 2013 Cummins ISX diesel engine using low octane gasoline (RON80). In the analysis-driven development process, a 1D engine system-level analysis was closely coupled with closed-cycle 3D CFD GCI combustion development. Three different boost systems were investigated using a validated 1D engine model: 1) the production turbocharger; 2) an off-the-shelf single-stage waste-gate turbocharger; 3) a prototype single-stage variable geometry turbocharger. For each boost system, three EGR configurations were evaluated: 1) a high-pressure EGR route; 2) a low-pressure EGR route; 3) a dual-loop EGR route. The air-handling system performance was first investigated over five steady-state engine operating conditions extracted from the ramped modal cycle supplemental emissions test. Then, through cosimulation using a Simulink-based engine controls model, the best performing candidates under transient operation through the Heavy-Duty Federal Test Procedure certification cycle were identified. The production turbocharger, designed for 4–6 g/kWh engine-out NOx, suffered from low combined turbocharger efficiency under the low-NOx GCI thermal boundary conditions. The prototype 1-Stage variable geometry turbocharger, when used with a high-pressure EGR configuration, demonstrated higher combined efficiencies, while the waste-gate turbocharger showed the best results when used with a dual-loop EGR system. All low-pressure only EGR configurations were found to incur additional pumping penalties due to the need for a back pressure valve to drive sufficient EGR levels. In the transient test cycle analysis, the single-stage high-pressure EGR system was capable of delivering the target boost and EGR, while the off-the-shelf waste-gate turbocharger, with its higher mass inertia, showed slower turbine response and a resulting lag in boost response. Unsurprisingly, the dual-loop EGR system also suffered from delays in EGR delivery during engine acceleration. In summary, the prototype single-stage variable geometry turbocharger with a high-pressure EGR system produced the best performance over both the steady-state and transient engine cycles and was identified as the best candidate for the prototype low-NOx heavy-duty GCI engine.

Air Supply System Design of a Diesel–Brayton Combined Cycle Engine

Numerical Study on the Performance of Centrifugal Compressor in the Combined Diesel-Brayton Cycle Engine

Study of a Hybrid Pneumatic-Combustion Engine under Steady-State and Transient Conditions for Transport Application

Simulation and Experimental Research on a Mixed Pulse Converter Turbocharging System

Thermodynamic Design and Optimization of the Multi-Branch Closed Brayton Cycle Based Precooling-Compression System for a Novel Hypersonic Aeroengine

Tailored Air-Handling System Development for Gasoline Compression Ignition in a Heavy-Duty Diesel Engine

Optimisation of the Design Parameters of a Compressed Air Engine Based on Numerical Simulation

Numerical and Experimental Investigation of A Compressor with Active Self-Recirculation Casing Treatment for A Wide Operation Range

Exploring the Combustion Performance of a Non-Road Air-Cooled Two-Cylinder Turbocharged Diesel Engine

Optimization of Supercritical Carbon Dioxide Recompression Brayton Cycle Considering Anti-Condensation Design of Centrifugal Compressor

Modeling and Performance Analysis of a Pre-Cooling and Power Generation System Based on the Supercritical CO2 Brayton Cycle on Turbine-Based Combined Cycle Engines

A Method of Turbocharger Design Optimization for a Diesel Engine with Exhaust Gas Recirculation

Design of transonic centrifugal compressor for vehicle

Challenges for Developing and Marketing a Brayton-Cycle Based Power Genset Gas-Turbine Using Supercritical CO2 and a Compressor Design for Simple Recuperated Cycle

Compressor Design For Multi-Point Operating Conditions Of Turbocharged Gasoline Engines

Strategy on Performance Improvement of Inverse Brayton Cycle System for Energy Recovery in Turbocharged Diesel Engines

System-component Combined Design and Comprehensive Evaluation of Closed-Air Brayton Cycle

An Experimental and Computational Investigation of Tailor-Developed Combustion and Air-Handling System Concepts in a Heavy-Duty Gasoline Compression Ignition Engine

Power augmentation and Ramp-Up rate improvement through compressed air Injection: A dry low NOx combustor CFD analysis

Numerical Analysis of Flow Interaction of Turbine System in Two-Stage Turbocharger of Internal Combustion Engine

Parameter Study Of A Brayton Cycle Waste Heat Recovery System For Turbocharged Diesel Engines