Abstract:Conductive polymer composites (CPCs) exhibit favorable density and corrosion resistance for application as bipolar plate (BP) in proton exchange membrane fuel cell (PEMFC). However, achieving CPCs that combine the required level of electrical conductivity and mechanical strength is a challenge that has limited their application in PEMFC BPs. This study explored the potential of achieving CPC BPs with high electrical and mechanical performance by using carbon black (CB) as a secondary filler in graphite-polymer composites. Polypropylene (PP)/epoxy blend was selected as the matrix due to its good combination of strength and toughness as well as its potential to form a co-continuous morphology, which promotes the formation of more continuous conducting networks within the composite, leading to enhanced electrical performance. The PP/epoxy/graphite/CB composites were prepared by melt mixing in a Rheomixer at 190 °C and 60 rpm for 10 min, followed by compression molding at 200 °C and 6 metric tonnes for 10 min. The electrical conductivity of the composites increased from 49.26 Scm−1 to 90.34 Scm−1 (in-plane) and from 0.37 Scm−1 to 9.34 Scm−1 (through-plane) as the total filler content increased from 50 to 85 wt%. The flexural strength initially increased from 45.57 MPa at 50 wt% to 51.84 MPa at 60 wt% total filler content. Further increase in total filler content led to a decrease in flexural strength. The nanosize CB particles, used as a minor filler, filled the voids between the graphite particles, leading to the formation of more conducting pathways and higher electrical conductivities compared to the PP/epoxy/graphite composites without CB fillers. The PP/epoxy/graphite/CB composite with 80 wt% total filler content exhibited the most promising in-plane conductivity (88.5 Scm−1), through-plane conductivity (8.52 Scm−1), and flexural strength (28.53 MPa) for BP application.

Preparation of Thermostable Electroconductive Composite Plates from Expanded Graphite and Polyimide

Polybenzimidazole/ionic-liquid-functional Silica Composite Membranes with Improved Proton Conductivity for High Temperature Proton Exchange Membrane Fuel Cells

Cross-Linkable Polymeric Ionic Liquid Improve Phosphoric Acid Retention and Long-Term Conductivity Stability in Polybenzimidazole Based PEMs

Effect of molding temperature on the properties of phenolic resin/carbon black/graphite composite bipolar plates

Investigating the Integration of Nonwoven Carbon Fibers for Mechanical Enhancement in Compression Molded Fiber-Reinforced Polymer Bipolar Plates

Fabrication of Electrically Conductive Polymer Composites for Bipolar Plate by Two‐step Compression Molding Technique

Preparation and Performance Study of PEK‐C‐OH/MWCNT‐COOH/Graphite Composite Bipolar Plates for PEMFCs With Improved Interface Properties

Preparation and properties of high performance nanocomposite bipolar plate for fuel cell

High-Precision Thin Wall Bipolar Plates for Fuel Cell Applications via Injection Compression Molding with Dynamic Mold Temperature Control

Collective Enhancements on Thermal-Electrical and Mechanical Properties of Graphite-Based Composite Bipolar Plates through the Coupled Manipulations of Molding and Impregnation Pressures

Gel-state Polybenzimidazole Proton Exchange Membranes with Flexible Alkyl Sulfonic Acid Side Chains for a Wider Operating Temperature Range (25–240 °C)

Novel Cross-Linked Membranes Based on Polybenzimidazole and Polymeric Ionic Liquid with Improved Proton Conductivity for HT-PEMFC Applications

Interlayer decoration of expanded graphite by polyimide resins for preparing highly thermally conductive composites with superior electromagnetic shielding performance

Expanded graphite (EG)/Ni@Melamine foam (MF)/EG sandwich-structured flexible bipolar plate with excellent electrical conductivity, mechanical properties, and gas permeability

Ionically Crosslinked Composite Membranes from Polybenzimidazole and Sulfonated Poly (fluorenyl ether ketone) for High-Temperature PEM Fuel Cells

Polybenzimidazole and ionic liquid composite membranes for high temperature polymer electrolyte fuel cells

Carbon/Carbon Composite Bipolar Plate for Proton Exchange Membrane Fuel Cells

Preparing Amorphous Graphite/resin Bipolar Plate by Mould Pressing Process

Electrical and mechanical properties of polypropylene/epoxy blend-graphite/carbon black composite for proton exchange membrane fuel cell bipolar plate

High performance polyvinylidene fluoride/graphite/multi-walled carbon nanotubes composite bipolar plate for PEMFC with segregated conductive networks