Pd/TiC/Ti Electrode with Enhanced Atomic H* Generation, Atomic H* Adsorption and 2,4-DCBA Adsorption for Facilitating Electrocatalytic Hydrodechlorination

Zimo Lou,Zheni Wang,Jiasheng Zhou,Chuchen Zhou,Jiang Xu,Xinhua Xu

DOI: https://doi.org/10.1039/d0en00182a

2020-01-01

Environmental Science Nano

Abstract:Efficient dechlorination of a chlorinated aromatic compound was achieved with the application of a novel Pd/TiC/Ti electrode.

What problem does this paper attempt to address?

TiC Doped Palladium/nickel Foam Cathode for Electrocatalytic Hydrodechlorination of 2,4-DCBA: Enhanced Electrical Conductivity and Reactive Activity

Zimo Lou,Yizhou Li,Jiasheng Zhou,Kunlun Yang,Yuanli Liu,Shams Ali Baig,Xinhua Xu

DOI: https://doi.org/10.1016/j.jhazmat.2018.08.066

IF: 13.6

2019-01-01

Journal of Hazardous Materials

Abstract:Titanium carbide (TiC) with excellent electrical conductivity, chemical and thermal stabilities has been recognized as one of the most promising electrocatalysts. A novel cathode, titanium carbide doped palladium/nickel foam (TiC-Pd/Ni foam), was synthesized via electroless deposition to improve the performance of Pd/Ni foam in electrocatlytic hydrodechlorination (ECH). TiC can be co-precipitated onto the surface of cathode during galvanic replacement reaction between Pd(II) solution and Ni foam. Both constant potential and constant current tests proved that TiC-Pd/Ni foam cathode performed remarkably higher activity for 2,4-dichlorobenzoic acid (2,4-DCBA) than Pd/Ni foam cathode, owing to the excellent conductivity of TiC and enhanced water dissociation over TiC-Pd/Ni foam cathode. Under the optimized reaction conditions of -0.85 V (vs Ag/AgCl), electrolyte of 10 mM and initial pH of 4, 99.8% of aqueous 2,4-DCBA (0.2 mM) was removed within 90 min. The removal process of the aqueous 2,4-DCBA obeyed first-order decay kinetic model. Over 86.3% of 2,4-DCBA can still be removed by TiC-Pd/Ni foam cathode in the fifth consecutive run within 120 min, which was much higher than that of Pd/Ni foam cathode (37.5%). Consequently, TiC-Pd/Ni foam cathode was a promising design for enhanced ECH activity and reduced operation cost.
TiO2@PDA inorganic-organic core-shell skeleton supported Pd nanodots for enhanced electrocatalytic hydrodechlorination

Zhefei Zhao,Li Yu,Lingxia Zheng,Tianyang Guo,Zhuoqing Lv,Shuang Song,Huajun Zheng

DOI: https://doi.org/10.1016/j.jhazmat.2022.128998

IF: 13.6

2022-08-01

Journal of Hazardous Materials

Abstract:The development of catalysts with high atom utilization and activity is the biggest challenge for electrocatalytic hydrodechlorination (EHDC) technology. Herein, a design strategy of TiO2@PDA inorganic-organic core-shell skeleton for loading lower dosage of noble palladium (Pd) with robust activity is reported. The self-supported TiO2@PDA nanorod arrays provides exposed surface area for anchoring Pd and PDA as interlayer controls the Pd nucleation to form nanodots with high dispersion, realizing high atom utilization. Moreover, the strong interaction between PDA and Pd realizes the coexistence of electron-rich and deficient Pd species with suitable proportion, which facilitate the H* formation and the C-Cl bond activation, respectively, resulting in the promoted activity. The optimal TiO2@PDA/Pd electrode exhibits a low dosage of Pd (0.093 mg cm−2) and excellent activity for 4-chlorophenol reduction with a mass activity (MA) of 23.96 min−1g−1, which is 3.31 times as high as that of TiO2/Pd. The design scheme with inorganic-organic core-shell skeleton as support is benefit for developing highly efficient and lower price elctrocatalysts for EHDC.

environmental sciences,engineering, environmental
Preparation and electrocatalytic dechlorination performance of Pd/Ti electrode

jingli zhang,zhanping cao,yongzhi chi,liping xie,ligang lin

DOI: https://doi.org/10.1080/19443994.2014.903205

IF: 1.1

2015-01-01

Desalination and Water Treatment

Abstract:The Pd/Ti working electrode was prepared by the electrochemical deposition on the Ti plate and its structure and morphology were analyzed by an X-ray diffraction (XRD) and a transmission electron microscopy. The results showed that Palladium (Pd) crystals were coated uniformly on Titanium (Ti) base material with the average size of 8.69 nm. The cyclic voltammetry was employed to study the electrochemical reduction characteristics of 2,4,5-tripolychlorinated biphenyl (PCB29) in an electrocatalytic system. The results showed that the PCB29 dechlorination was a two-electron transfer reduction controlled by adsorption and conformed to the characteristics of the first-order reaction. The efficiencies of PCB29 degradation in the electrocatalytic system were more than 95% after 5 h at its concentration (mg/L) of 60, 80, and 100. The dechlorinations of PCB29 obeyed the pseudo-first-order reaction kinetic behavior. The reaction rate constant was approximately 0.011 min(-1). The reaction rate increased slightly as the temperature rose. The 2,5-PCB was first mainly generated by PCB29 para-position dechlorination, 2-PCB by meta-position dechlorination, and then diphenyl by the subsequent ortho-position dechlorination. Diphenyl could be further hydrogenated to phenyl cyclohexane. The chlorine substitution position on PCB29 mainly affected the order of PCB29 electrocatalytic dechlorination.
Enhanced atomic H* utilization on urchin-like TiO 2 -suppoted palladium nanoparticles for efficient electrocatalytic detoxification of chlorinated organics

Jun Zhang,Shuyue Liu,Shiyu Lu,Chunyuan Wang,Pingjuan Liang,Huan Yi,Mengjie Li,Laizheng Luo,Rong Wang,Guangming Jiang

DOI: https://doi.org/10.1016/j.fuel.2024.131001

IF: 7.4

2024-01-29

Fuel

Abstract:Improving the utilization of hydrogen radicals (H*) is of great significance for effective Pd-mediated electrocatalytic hydrodechlorination (EHDC) in detoxifying chlorinated organic pollutants (COPs). However, the limited H* utilization by single Pd arises from its inadequate performance in adsorbing/activating COPs and inferior mass transfer of low-concentration COPs. In this study, an urchin-like yolk/shell TiO 2 spheres with mesoporous structure are developed for supporting Pd nanoparticles (Pd/U-TiO 2 ), which exhibits superior EHDC activity and selectivity for 2,4-DCP reduction. Notably, the prepared Pd/U-TiO 2 catalyst achieves a mass activity of 4.2 min −1 g Pd -1 and a specific activity of 1.94 min −1 mol Pd -1 when detoxifying 50 mg/L of 2,4-DCP at −0.85 V, surpassing the most reported catalysts. Furthermore, the Pd/U-TiO 2 catalyst consistently demonstrates higher H* utilization efficiency compared to single Pd, regardless of the 2,4-DCP concentration or reaction mode (batch or continuous-flow). This enhanced H* utilization efficiency is attributed to two key factors: the urchin-like and yolk/shell structure of U-TiO 2 enhances the mass diffusion of 2,4-DCP, and the strong interactions between Pd and U-TiO 2 generate electron-rich Pd species that enhance the adsorption and activation of COPs. Overall, this work highlights the synergistic effects of strong metal-support interactions and mass diffusion in enhancing atomic H* utilization. This study lays a significant experimental and theoretical foundation for designing efficient electrocatalysts for the detoxification of chlorinated organic pollutants and various other halogenated organic pollutants.

energy & fuels,engineering, chemical
Enhanced electrocatalytic hydrodechlorination by modulating metal-support interaction and H generation of single-Pd-atom anchored NiFeP electrode

Zhefei Zhao,Xuyao Yao,Ruopeng Yu,Xingyu Luo,Minhao Chen,Xiangxiang Zhang,Yinghua Xu,Youqun Chu,Xinbiao Mao,Huajun Zheng

DOI: https://doi.org/10.1016/j.cej.2024.152340

IF: 15.1

2024-05-24

Chemical Engineering Journal

Abstract:Electrocatalytic hydrodechlorination (EHDC) stands out as an economical and prospective technology for eliminating chlorinated organic pollutants. Single-atom catalyst engineering and metal-support interaction (MSI) offer the promising strategies for developing electrocatalysts with high atom utilization and reactivity. Herein, atomically dispersed palladium (Pd) anchored on the iron (Fe)-introduced nickel phosphide (NiFeP) support is reported. The prepared NiFeP-Pd electrode exhibits outstanding electrocatalytic activity in 4-CP removal efficiency (98.8 %) with an ultra-low dosage of Pd (0.0497 mg cm −2 ) and the highest reported MA value (446.01 min −1 g −1 ), surpassing Ni 2 P-Pd by 6.34 times. Experimental results combined with theoretical calculations suggest that the superior performance of NiFeP-Pd stems from the modulated support by Fe introduction, which not only enhances the generation of adsorbed atomic hydrogen species (H*), but also reduces the energy barrier of C-H formation on Pd sites by regulating the MSI. In addition, single-Pd-atom construction on NiFeP with good conductivity and large specific surface area makes the contributions as well.

engineering, chemical, environmental
Enhanced indirect atomic H* reduction at a hybrid Pd/graphene cathode for electrochemical dechlorination under low negative potentials

Ran Mao,Huachun Lan,Li Yan,Xu Zhao,Huijuan Liu,Jiuhui Qu

DOI: https://doi.org/10.1039/c8en00727f

2018-01-01

Abstract:A Pd/reduced graphene oxide (rGO) hybrid catalyst was fabricated on carbon fiber paper (CFP) via chemical reduction and a subsequent electrodeposition process. The catalytic properties of Pd/rGO/CFP were assessed in electroreductive dechlorination of trichloroacetic acid (TCAA), one of the most common disinfection by-products. In comparative tests of CFP, rGO/CFP, Pd/CFP, and Pd/rGO/CFP, atomic H* could be generated at all four electrodes by an appropriate choice of the applied potential, while Pd/rGO/CFP exhibited superior properties, with the lowest overpotential of -0.5 V. As evidenced by scavenger experiments, TCAA dechlorination mainly proceeded via indirect H* reduction at the Pd-containing catalytic electrodes. DFT calculations indicated easier adsorption of H* on the rGO supported Pd as compared to the bare Pd (E-ads: -3.63 eV vs. -2.93 eV), thereby resulting in an enhanced ability for Pd/rGO/CFP to retain a high surface concentration of atomic H*. Due to the enhanced production of H* stemming from electronic coupling between Pd and rGO sheets, combined with the unique ability of rGO-supported Pd particles to adsorb atomic H*, the hybrid Pd/rGO/CFP cathode possessed superior catalytic properties for TCAA dechlorination.
Unveiling the efficient state of Pd catalyst for robust electrocatalytic hydrodechlorination

Shuyuan Xu,Bingbao Mei,Fengjiao Li,Jianing Mao,Changxing Huang,Yufeng Yan,Ningning Chen,Yinghua Xu,Meiqin Shi

DOI: https://doi.org/10.1088/1361-6528/aceb6b

IF: 3.5

2023-07-30

Nanotechnology

Abstract:The application of electrochemical hydrodechlorination has been impeded due to the low utilization and activity of Pd catalyst. Herein, a series of Pd catalysts were prepared via the controllable evolution of Zn state during the pyrolysis of ZIF-8 nanosheet. Various forms of Pd with different chemical surroundings were generated upon the combined use of galvanic displacement and ion exchange process. Electrocatalytic hydrodechlorination of 4-chlorophenol was performed and the EHDC efficiency of Pd/CN reaches 100 % within 3 h at extra low Pd concentration. The coexistence of zero-valent Pd (Pd 0 ) and nitrogen coordinated Pd (Pd-N) was verified by XAFS which provide multiple active sites for focusing on adsorbing H* and cracking C-Cl respectively. The synergetic effect between different chemical state of Pd for efficient hydrodechlorination of chloroaromatics and scheme for dexterous preparation of Pd based electrocatalyst are proposed and discussed.

materials science, multidisciplinary,physics, applied,nanoscience & nanotechnology
Mxene-functionalized metal–organic frameworks enhancing the generation of active hydrogen atoms for efficient electrocatalytic hydrodechlorination

Qinghao Zhao,Chunchao Chen,Jiahua Fu,Yapeng Zhang,Jinyan Huo,Hongbo Zeng,Qingfeng Xu,Jianmei Lu

DOI: https://doi.org/10.1016/j.seppur.2024.128040

IF: 8.6

2024-05-25

Separation and Purification Technology

Abstract:To simultaneously reduce the usage of Pd and enhance the generation of active hydrogen atoms (H*), a novel Pd/MXene@Ni-MOF/NF composite was reported for electrocatalytic hydrodechlorination (EHDC). The synthesized catalyst delivered excellent activity, successfully achieving complete removal of 2-chlorophenol (2-CP) within 90 min and the rate constant was approximately 2.8 times higher than that of Pd/NF catalyst. Additionally, Pd/MXene@Ni-MOF/NF composites also showed a full range of pH tolerance, excellent ion interference resistance and long-term stability. Mechanistic studies suggested that the modification of MXene improved the electrocatalytic properties of Ni-MOF and the generation of H* by its optimized hydrophilicity, electrical conductivity and structural stability, which offered sufficient active species for the conversion of 2-CP to phenol on Pd nanoparticles.

engineering, chemical
Electrodeposition Decoration of Pd0 on F‐Co(OH)2 Nanoarrays with Intentionally Introduced Pd2+ Species for Efficient Electrocatalytic Hydrodechlorination of 2,4‐dichlorophenol

Rui Xiang,Yingxue Yu,Qing Gao,Yujuan Zhuang,Chengyun Wang,Lishan Peng

DOI: https://doi.org/10.1002/ejic.202400602

IF: 2.551

2024-10-16

European Journal of Inorganic Chemistry

Abstract:Developing a Pd‐based catalyst possessing high efficiency and low mass loading remains a big obstacle for the large‐scale application of electrocatalytic hydrodechlorination (EHDC) of chlorophenols (CPs). Herein, high dispersion Pd nanoparticles imbedded in Pd2+ hydroxide species are decorated on the surface of F‐Co(OH)2 nanowire arrays with a newly developed electrodeposition and hydrolysis coupled process. EHDC of 2,4‐dichlorophenol (2,4‐DCP) with the as‐obtained Pd/F‐Co(OH)2/NF‐a exhibits superior performance than other control samples in this work and literature reports. A 100% removal of 2,4‐DCP is accomplished within 120 min, featuring fast reaction kinetics (kobs = 5.0 × 10‐2 min‐1) and mass activity (MA = 22.2 min‐1 g‐1Pd). Mechanism investigation shows that the intentionally introduced Pd2+ sites play a pivotal role in the adsorption of 2,4‐DCP, while high dispersion of Pd facilitates the generation of active H*, thus promoting the catalytic performance. This work presents a valuable example for designing high‐performance Pd‐based EHDC catalysts by composition tuning.

chemistry, inorganic & nuclear
Noble-metal-free 3D hierarchical Ni-WC heterostructure with enhanced interfacial charge transfer for efficient electrocatalytic hydrodechlorination

Qi Wang,Jing Du,Yuan-Yuan Ma,Xiao-Yu Yin,Ze-Yu Tian,Zhan-Gang Han

DOI: https://doi.org/10.1016/j.cej.2022.139107

IF: 15.1

2023-01-01

Chemical Engineering Journal

Abstract:Electrocatalytic hydrodechlorination (EHDC) provides a promising approach to efficiently remove the halogenated organic pollutants in water. Herein, a kind of noble-metal-free three-dimensional (3-D) hierarchical nickel-tungsten carbide (Ni-WC) heterostructure supported on nickel foam (NF) (Ni-WC/NF) was fabricated via the in-situ hydrothermal growth and annealing treatment of Ni,W-rich polyoxometalate {Ni54W72}. Featuring self-supported 3-D hierarchical skeleton structures and abundant Ni-WC interfaces, Ni-WC/NF exhibited high-efficient EHDC performance towards 4-chlorophenol (4-CP) with 100 % conversion efficiency in 3 h, large reaction rate constant of 2.2 × 10-2 min−1 and high current efficiency of 13.9 %, which is comparable to the-state-of-the-art Pd-based catalysts. The active atomic hydrogen (H*) generation kinetics and the interactions of Ni-WC heterostructure with 4-CP/phenol were evaluated. DFT calculations demonstrated that the coverage of 4-CP determines the EHDC efficiency, the Ni-WC heterostructure optimizes the electronic structure of Ni, enhances the adsorption of 4-CP and facilitates the desorption of phenol, thus promoting EHDC performance. This work provides an efficient noble-metal-free catalyst for enhanced electrochemical dechlorination in organic-pollutant treatment.

engineering, chemical, environmental
Atomically dispersed Pd electrocatalyst for efficient aqueous phase dechlorination reaction

Zhechuan Mao,Linghui Liu,Hong Bin Yang,Yangliang Zhang,Zeqing Yao,Huan Wu,Yanqiang Huang,Yinghua Xu,Bin Liu

DOI: https://doi.org/10.1016/j.electacta.2021.138886

IF: 6.6

2021-09-01

Electrochimica Acta

Abstract:High atom utilization is important for practical application of Pd catalysts in dechlorination of chlorinated organic pollutants (COPs). Herein, we report atomically dispersed Pd (coordinated with 2 pyridinic N) anchored on N-doped carbon (A-Pd-NC) as an efficient catalyst toward electrochemical dechlorination of COPs in aqueous solution. Constant current electrolysis showed that the A-Pd-NC catalyst possessed a much higher dechlorination activity (DA, 98.9 mmol•g−1•h−1) than commercial Pd/C (2.4 mmol•g−1•h−1). Using A-Pd-NC as an effective electrocatalyst, near 100% product selectivity of 4-chlorophenol to phenol could be achieved at pH = 3. Constant potential electrolysis, cyclic voltammetry (CV), electron spin resonance (ESR), X-ray photoelectron spectroscopy (XPS) and density functional theory (DFT) calculation results suggested that the dechlorination stability of A-Pd-NC was dependent on the potential applied on the catalyst and the dechlorination reaction followed the hydrodechlorination mechanism with electrochemically adsorbed H as the reductant.

electrochemistry
Atomic hydrogen-mediated enhanced electrocatalytic hydrodehalogenation on Pd@MXene electrodes

Lan-Ying Liu,Guo-Shuai Liu,Shi-Ming Niu,He Liu,Min-Hua Cui,Ai-Jie Wang

DOI: https://doi.org/10.1016/j.jhazmat.2023.132113

IF: 13.6

2023-07-24

Journal of Hazardous Materials

Abstract:In this study, a catalyst was synthesized to enhance the electrocatalytic hydrodehalogenation (ECH) of emerging halogenated organic pollutants (HOPs) by improving the dispersibility, catalytic activity , and stability of palladium (Pd). The average size of Pd nanoparticles (NPs) was reduced to 3.62 ± 0.34 nm with a more intensive peak of Pd (111), which facilitated atomic hydrogen (H*) production. The /CC electrode demonstrated superior ECH activity for diclofenac (DCF) degradation, with a reaction rate constant ( k obs ) 2.48 times higher than that of Pd/CC (without MXene). The satisfactory ECH performance of /CC remained consistent within a wide range of initial DCF concentrations (5–100 mg/L), and no significant ECH attenuation was observed even after up to 10 batches. Furthermore, the high activity of /CC was also observed in the ECH of other halogenated organic pollutants (levofloxacin, tetrabromobisphenol A, and diatrizoate). Density functional theory (DFT) calculations revealed that electronic configuration modulation of the catalyst optimized binging energies to H* , DCF, and dechlorinated products, thereby enhancing the ECH efficiency of DCF.

environmental sciences,engineering, environmental
Generation of adsorbed atomic hydrogen by Pd(II) doped Fe(OH)2 enables ultra-fast reductive dechlorination of trichloroethylene

Li-Zhi Huang,Yi Wang,Jia Deng,Jianping Yuan,Yitao Dai,Weizhao Yin

DOI: https://doi.org/10.1016/j.apcatb.2022.122094

2023-03-01

Abstract:Trichloroethylene (TCE) is a notorious persistent pollutant in groundwater, while most reductive dechlorination processes result in the formation of toxic less-chlorinated by-products. In this work, adsorbed atomic hydrogen (H*) was produced by Pd(II) doped Fe(OH)2, which was used for ultra-fast reductive dechlorination of TCE without the formation of less-chlorinated by-products. When the Fe(OH)2 dosage is 0.5 mM and the Pd(II) dosage is 20 μM, TCE (42 μM) is completely removed in 60 min with the pseudo first-order reaction rate constant of 7.74 h−1. Radical quenching experiment and electrochemical analysis both confirmed that adsorbed H* rather than absorbed H* contribute to the reduction of TCE. Density function theory calculation demonstrated that small Pd clusters were more beneficial to TCE dechlorination than large Pd clusters. The pseudo first-order rate constant for TCE reduction in real groundwater was as high as 0.018 min–1, demonstrating the potential application of Pd/Fe(OH)2 in groundwater remediation.

chemistry, physical,engineering, chemical, environmental
H*ads dynamics engineering via bimetallic Pd-Cu@MXene catalyst for enhanced electrocatalytic hydrodechlorination

Lan-Ying Liu,Min-Hua Cui,John Justo Ambuchi,Shi-Ming Niu,Xin-Hui Li,Wo-Long Wang,He Liu,Guo-Shuai Liu,Ai-Jie Wang

DOI: https://doi.org/10.1016/j.envres.2024.118859

2024-07-01

Abstract:Electrocatalytic hydrodechlorination (EHDC) is a promising approach to safely remove halogenated emerging contaminants (HECs) pollutants. However, sluggish production dynamics of adsorbed atomic H (H*ads) limit the applicability of this green process. In this study, bimetallic Pd-Cu@MXene catalysts were synthesized to achieve highly efficient removal of HECs. The alloy electrode (Pd-Cu@MX/CC) exhibited better EHDC performance in comparison to Pd@MX/CC electrode, resulting in diclofenac degradation efficiency of 93.3 ± 0.1%. The characterization analysis revealed that the Pd0/PdII ratio decreased by forming bimetallic Pd-Cu alloy. Density functional theory calculations further demonstrated the electronic configuration modulation of the Pd-Cu@MXene catalysts, optimizing binging energies for H* and thereby facilitating H*ads production and tuning the reduction capability of H*ads. Noteably, the amounts and reduction potential of H*ads for Pd-Cu@MXene catalysts were 1.5 times higher and 0.37 eV lower than those observed for the mono Pd electrode. Hence, the introduction of Cu into the Pd catalyst optimized the dynamics of H*ads production, thereby conferring significant advantages to EHDC reactions. This augmentation was underscored by the successful application of the alloy catalysts supported by MXene in EHDC experiments involving other HECs, which represented a new paradigm for EHDC for efficient recalcitrant pollutant removal by H*ads.
Modulating Adsorption of Active Hydrogen Atoms on Palladium Nanoparticles: Doping Ruthenium into Metal–Organic Frameworks for Efficient Electrocatalytic Hydrodechlorination

Chunchao Chen,Liujun Jin,Huilong Dong,Jun Jiang,Hao Feng,Dongyun Chen,Najun Li,Qingfeng Xu,Jianmei Lu

DOI: https://doi.org/10.1016/j.seppur.2023.124527

2023-01-01

Abstract:To simultaneously optimize the dispersion and electrocatalytic activity of palladium (Pd) nanoparticles, we report a novel Pd-NiRu-MOF/NF composite electrode with low noble metal dosage for electrocatalytic hydrodechlorination. The as-prepared electrode exhibits outstanding activity, particularly the complete dechlorination of 2-chlorophenol within 75 min at -0.85 V, outperforming reported state-of-the-art electrode materials. Moreover, the catalytic activity could be well-maintained after continuous five catalytic cycles and even 30-day exposure to air as well as deliver excellent catalytic performance for other priority chlorophenols. CO-stripping experiments demonstrate that the dispersion of Pd nanoparticles increases the electrochemically active surface area of Pd. X-ray photoelectron spectroscopy and density functional theory analysis disclose that the electronic structure of Pd is modulated via introducing Ru atoms into Pd-Ni-MOF/NF, thereby enhancing the adsorption of H*ads on Pd-NiRu-MOF/NF and boosting the electroreductive remediation of chlorophenols. Notably, the electrochemical dechlorination of chlorophenols remains effective in natural water or soil, indicating that Pd-NiRuMOF/NF composite electrode has a good application potential in removing organic halides in wastewater or soil.
Carbon-nanotube-doped Pd-Ni Bimetallic Three-Dimensional Electrode for Electrocatalytic Hydrodechlorination of 4-Chlorophenol: Enhanced Activity and Stability.

Yifan Wu,Ling Gan,Shupeng Zhang,Haiou Song,Chang Lu,Wentao Li,Zheng Wang,Bicun Jiang,Aimin Li

DOI: https://doi.org/10.1016/j.jhazmat.2018.05.034

IF: 13.6

2018-01-01

Journal of Hazardous Materials

Abstract:A novel composite bimetallic electrode, palladium-nickel/multi-walled carbon nanotubes/graphite felt (Pd-Ni/MWCNTs/GF), was synthesized for the electrocatalytic hydrodechlorination of 4-chlorophenol (4-CP). GF with a three-dimensional structure was used as the electrode substrate, and doped with MWCNTs, which can improve the GF conductivity and serve as a skeleton for metal loading. Ni and Pd were deposited on the electrode surface stepwise to obtain a well-aligned, highly active and stable Pd-Ni/MWCNTs/GF electrode. The Pd-Ni/MWCNTs/GF cathode showed a high reactivity for the electrocatalytic hydrodechlorination of 4-CP; up to 100% removal of 4-CP was achieved within 30 min, and followed pseudo-first-order kinetics with a rate constant of 0.162 min-1. Compared with other cathodes, the Pd-Ni/MWCNTs/GF electrode showed superior performance in 4-CP reduction. Excessive current will lower the reaction efficiency and current efficiency because of hydrogen evolution, and acidic solution conditions are more conducive to electrocatalytic reactions. Experiments confirmed that the Ni had a small amount of loss under acidic conditions but remained stable under neutral and alkaline conditions, whereas the loss of Pd for different pH values was constantly low. In cycle tests, the bimetallic electrode exhibits a better reactivity and stability than the single-metal Pd electrode in the long-term.
Construction of Pd nanoparticles/two-dimensional Co-MOF nanosheets heterojunction for enhanced electrocatalytic hydrodechlorination

Zimo Lou,Chaochao Yu,Xiaofei Wen,Yinghua Xu,Jianming Yu,Xinhua Xu

DOI: https://doi.org/10.1016/j.apcatb.2022.121730

2022-01-01

Abstract:To simultaneously enhance the catalytic activity of Pd and lower its dosage, we report a Pd/Co-MOF nanosheets/ Ni foam electrode (Pd/Co-MNSs/Ni foam) with conductive 2D MOF nanosheets as interlayer for electrocatalytic hydrodechlorination (ECH). Such electrode delivers high ECH activity for nearly complete dechlorination (similar to 97%) of chloramphenicol (CAP) with an apparent rate constant of 0.11 min(-1), outcompeting the well-reported and the commercial electrode materials. Pd/Co-MNSs/Ni foam maintains its activity after 9 consecutive runs and 5-day exposure to air, and shows rapid degradation kinetics for other priority contaminants. The formation of Pd/Co-MNSs heterojunction interface increases the electron density of metallic Pd and brings the d states closer to Fermi level than Pd alone, thus optimizing the binding of ECH intermediates. This support construction-based strategy tunes the interface of catalytic electrode to expose active sites and modulate the electronic states of catalyst to promote intrinsic activity, boosting electroreductive remediation of organic halides.
Ultra-low-loading Pd nanocrystals modified Ni foam electrode for efficient electrochemical hydrodechlorination

Huan Wu,Zhechuan Mao,Baoquan Liu,Deyin Chen,Meiqin Shi,Bosheng Lv,Yinghua Xu,Lianbang Wang

DOI: https://doi.org/10.1016/j.apcatb.2023.122978

2023-11-01

Abstract:Pd nanocrystals modified Ni foam electrode (Pd NCs/Ni) with Pd loading of 12.5 μg cm−2 was prepared via electrodeposition and exhibited higher mass activity in the electrochemical hydrodechlorination. With the assistance of polyvinylpyrrolidone and bromide ion, Pd nanocrystals with abundant catalytic sites were uniformly anchored on both the inner and surfaces of the Ni foam. Six chlorophenols were rapidly dechlorinated to phenol using Pd NCs/Ni with high conversion (> 98%) and selectivity (∼ 100%). Pd NCs/Ni showed broad applicability to various reaction conditions and maintained stable activity over 12 consecutive cycles. The electrochemical hydrodechlorination follows the indirect dechlorination mechanism. Hydrogenolysis between adsorbed H and chlorophenols is the rate-controlling step. Low coordination Pd atoms on the faces of Pd (220) and Pd (311) are the main catalytic sites. The study provides a valuable insight of high performance and low cost Pd modified electrode and its catalytic mechanism in electrochemical hydrodechlorination.

chemistry, physical,engineering, chemical, environmental
MnO2 Enhances Electrocatalytic Hydrodechlorination by Pd/Ni Foam Electrodes and Reduces Pd Needs

Zimo Lou,Jiasheng Zhou,Mei Sun,Jiang Xu,Kunlun Yang,Dan Lv,Yaping Zhao,Xinhua Xu

DOI: https://doi.org/10.1016/j.cej.2018.07.057

IF: 15.1

2018-01-01

Chemical Engineering Journal

Abstract:A Pd/MnO2/Ni foam electrode with hierarchical structure was synthesized via electrodeposition for efficient electrocatalytic hydrodechlorination. Compared with the ordinary Pd/Ni foam electrode, the introduction of MnO2 greatly enhanced the catalytic reactivity and reduced the dose of precious metal Pd. Only a quarter of Pd was required for the Pd/MnO2/Ni foam compared to the Pd/Ni electrode to achieve complete dechlorination of 2,4-dichlorobenzoic acid (2,4-DCBA) within 120 min. Various characterizations suggested that MnO2 covered the surface of the Ni foam and increased the specific surface area of the electrode, while Pd nanoparticles were subsequently deposited on MnO2. The atomic H∗-based indirect dechlorination was the dominant pathway while only approximately 13% of 2,4-DCBA was removed by direct electron transfer. Atomic H∗ adsorbed on Pd acted as the key active species for the dechlorination of 2,4-DCBA by the Pd/MnO2/Ni foam electrode in this study. The introduction of MnO2 would promote the water dissociation and the hydrogen evolution reaction, and provide Pd with more atomic H∗. Pd/MnO2/Ni foam exhibited good stability and reusability according to the XPS spectra and consecutive electrocatalytic experiments, which suggested its long-term potential for efficient removal of chlorinated contaminants. This work demonstrated a new strategy to design efficient electrocatalysts with less precious metal.
Regulating the electronic structure by P-doping cobalt-based catalyst for atomic hydrogen mediated electrocatalytic dechlorination

Ge Song,Huizhong Wu,Xuechun Wang,Shuaishuai Li,Ruiheng Liang,Minghua Zhou

DOI: https://doi.org/10.1016/j.jhazmat.2024.134750

IF: 13.6

2024-06-01

Journal of Hazardous Materials

Abstract:Electrocatalytic dechlorination by atomic hydrogen (H*) is efficient, but limited by the low efficiency of H* production. Herein, a phosphorus-doped cobalt nitrogen carbon catalyst (Co-NP/C) was prepared, which had high catalytic activity in a wide pH range (3−11). The turnover frequency of Co-NP/C (3.54 min −1 ) was 1.21–59000 times superior to that of current Pd-based and non-noble metal catalysts (0.00006–2.92 min −1 ). Co-NP/C significantly enhanced H* generation, which was 1.52, 2.44, and 3.77 times stronger than that of Co-N/C, NP/C, and N/C, respectively, since the introduction of phosphorus was found enhanced the electron density of cobalt and regulated the electron transfer. Co-NP/C showed outstanding catalytic performance after ten cycles and could achieve nearly complete chloramphenicol removal. This regulation method was verified to be effective for other non-noble metal (Fe, Mn, Cu, Ni) phosphorus doped catalysts, proposing a general class for efficient electrochemical dechlorination, which would be of great significance for the elimination of chlorinated organic pollutants.

environmental sciences,engineering, environmental

Pd/TiC/Ti Electrode with Enhanced Atomic H* Generation, Atomic H* Adsorption and 2,4-DCBA Adsorption for Facilitating Electrocatalytic Hydrodechlorination

TiC Doped Palladium/nickel Foam Cathode for Electrocatalytic Hydrodechlorination of 2,4-DCBA: Enhanced Electrical Conductivity and Reactive Activity

TiO2@PDA inorganic-organic core-shell skeleton supported Pd nanodots for enhanced electrocatalytic hydrodechlorination

Preparation and electrocatalytic dechlorination performance of Pd/Ti electrode

Enhanced atomic H* utilization on urchin-like TiO 2 -suppoted palladium nanoparticles for efficient electrocatalytic detoxification of chlorinated organics

Enhanced electrocatalytic hydrodechlorination by modulating metal-support interaction and H generation of single-Pd-atom anchored NiFeP electrode

Enhanced indirect atomic H* reduction at a hybrid Pd/graphene cathode for electrochemical dechlorination under low negative potentials

Unveiling the efficient state of Pd catalyst for robust electrocatalytic hydrodechlorination

Mxene-functionalized metal–organic frameworks enhancing the generation of active hydrogen atoms for efficient electrocatalytic hydrodechlorination

Electrodeposition Decoration of Pd0 on F‐Co(OH)2 Nanoarrays with Intentionally Introduced Pd2+ Species for Efficient Electrocatalytic Hydrodechlorination of 2,4‐dichlorophenol

Noble-metal-free 3D hierarchical Ni-WC heterostructure with enhanced interfacial charge transfer for efficient electrocatalytic hydrodechlorination

Atomically dispersed Pd electrocatalyst for efficient aqueous phase dechlorination reaction

Atomic hydrogen-mediated enhanced electrocatalytic hydrodehalogenation on Pd@MXene electrodes

Generation of adsorbed atomic hydrogen by Pd(II) doped Fe(OH)2 enables ultra-fast reductive dechlorination of trichloroethylene

H*ads dynamics engineering via bimetallic Pd-Cu@MXene catalyst for enhanced electrocatalytic hydrodechlorination

Modulating Adsorption of Active Hydrogen Atoms on Palladium Nanoparticles: Doping Ruthenium into Metal–Organic Frameworks for Efficient Electrocatalytic Hydrodechlorination

Carbon-nanotube-doped Pd-Ni Bimetallic Three-Dimensional Electrode for Electrocatalytic Hydrodechlorination of 4-Chlorophenol: Enhanced Activity and Stability.

Construction of Pd nanoparticles/two-dimensional Co-MOF nanosheets heterojunction for enhanced electrocatalytic hydrodechlorination

Ultra-low-loading Pd nanocrystals modified Ni foam electrode for efficient electrochemical hydrodechlorination

MnO2 Enhances Electrocatalytic Hydrodechlorination by Pd/Ni Foam Electrodes and Reduces Pd Needs

Regulating the electronic structure by P-doping cobalt-based catalyst for atomic hydrogen mediated electrocatalytic dechlorination