Abstract:In this study, the effect of Cr content on microstructure and electrochemical measurement of low alloy steel in 3.5 wt% NaCl solution was investigated using scanning electron microscope (SEM), X-ray diffractometer (XRD), X-ray photoelectron spectroscopy (XPS) and electrochemical workstation, and the CCT curves of the samples were calculated using JMatPro software. The results showed that the augmentation of Cr content inhibits the formation of ferrite and promotes the development of cementite in low alloy steels. And the reduction of Ar3 (the temperature at which austenite transforms to ferrite) and the increase in Ar1 (the temperature at which ferrite transforms to pearlite) also contribute to the expansion of the pearlite area. The XRD results show that the samples primarily consist of Fe-Cr solid solution with a body-centered cubic structure. As the Cr content increases, the peaks corresponding to the (110), (200), and (211) planes gradually enhance which means the improvement in the crystallinity of the samples. The improvement in the crystallinity can result in a decrease of grain size. Due to the suitable ratio of cementite to pearlite and the synergistic effect of grain size refinement, the Cr2 sample exhibits the best tensile property when the Cr content is 0.970 wt%. Cr(OH)3 and Cr2O3 with protective effects are generated in the corrosion film on the surface of Cr-containing low-alloy steels. And Cr also promotes the transformation of γ-FeOOH to α-FeOOH in the corrosion film because of the atomic radius of Cr3+ being smaller than that of Fe3+. These substances enhance the ability of the corrosion film to block corrosive media and protect the matrix. The results of the electrochemical measurement showed that the increasing Cr content from 0.970 to 4.657 wt% resulted in the enhancement of steel's corrosion resistance. The Cr4 sample exhibits the best corrosion resistance when the Cr content is 4.657 wt%.

Electrochemical behavior and corrosion products of Cr-modified reinforcing steels in saturated Ca(OH)2 solution with chlorides

Effect of DC Stray Current on Electrochemical Behavior of Low-Carbon Steel and 10%cr Steel in Saturated Ca(OH)2 Solution

Chloride-induced Corrosion Resistance of Low-Alloyed Reinforcement Steels in Two Different Ph Simulated Concrete Solution

Passive Behavior of New Alloy Corrosion Resistant Steel Cr10Mo1 in Chloride-containing Environment

Effects of Cr content on corrosion behaviour and corrosion products of spring steels

Passive Behaviour of New Alloy Corrosion Resistant Steel Cr10Mo1 in Simulating Concrete Pore Solutions with Different Chloride Contents

Corrosion Resistance of a Cr-Bearing Low-Alloy Reinforcing Steel: Effect of Surface Condition, Alkaline Solution, and Chloride Content

Passivation and depassivation properties of Cr–Mo alloyed corrosion-resistant steel in simulated concrete pore solution

Corrosion Resistance of Cr10Mo1 Alloy Corrosion-Resistant Steel in Seawater–Sea Sand Concrete Pore Solution

Passivation Characteristics Of Alloy Corrosion-Resistant Steel Cr10mo1 In Simulating Concrete Pore Solutions: Combination Effects Of Ph And Chloride

Investigating the effect of Cr content on the microstructure and electrochemical measurement of low alloy steel

Enhanced Corrosion Resistance of Reinforcing Steels in Simulated Concrete Pore Solution with Low Molybdate to Chloride Ratios

The Passive Film Growth Mechanism Of New Corrosion-Resistant Steel Rebar In Simulated Concrete Pore Solution: Nanometer Structure And Electrochemical Study

Effect Of Cr Content On The Electrochemical Behavior Of Low-Chromium X65 Steel In Co2 Environment

Influence of Surface Condition on the Electrochemical Behavior of Alloy Steel in Saturated Ca(OH)2 Solution

EIS analysis on chloride-induced corrosion behavior of reinforcement steel in simulated carbonated concrete pore solutions

Natural Passivation Behavior and Its Influence on Chloride-Induced Corrosion Resistance of Stainless Steel in Simulated Concrete Pore Solution

Long-Term Electrochemical Behavior of Low-Alloy Steel in Simulated Concrete Pore Solution with Chlorides

Atomic force microscopy and electrochemical investigation on the corrosion behavior of carbon steel passivated by molybdate and chromate.

Role of Red Mud in Natural Passivation and Chloride-Induced Depassivation of Reinforcing Steels in Alkaline Concrete Pore Solutions

Influence of Chloride Concentration and Pre-Passivation on the Pitting Corrosion Resistance of Low-Alloy Reinforcing Steel in Simulated Concrete Pore Solution