Abstract:Regarding the issue of intense mining pressure appearing in the underlying gateway below the remaining coal pillar in the close‐distance coal seam (the remaining coal pillar is perpendicular to the underlying section coal pillar), 401 working face is used as the engineering background. Field measurements, laboratory experiments, numerical simulations, and engineering verification techniques are used to study the abutment pressure's evolution properties and the plastic zone's propagation laws before and after the underlying coal seam roadway experienced the mining impact. The conclusions are as follows: 1 The maximum plastic area on the two sides and the roof of the roadway underlying the gob are up to 2 m and 1.5 m, whereas the maximum plastic area on the two sides and the roof of the roadway underlying the remaining coal pillar are up to 5 m and 4.5 m, respectively. Moreover, the plastic area extends along the two sides, and the section coal pillar is completely broken when the working face is mined below the remaining coal pillar. 2 The stress increase coefficient K in the overlap area of the remaining coal pillar and the underlying section coal pillar reaches 3.4 when the mining face penetrates the underlying remaining coal pillar and the advance abutment pressure is overlaid with the concentrated stress of the coal pillar. 3 When the underlying working face is mined to 4 m, ‐2 m, ‐8 m, and ‐14 m away from the remaining coal pillar, the damage range of the roadway 5‐10 m ahead increases in turn. At the same time, the maximum plastic area of the roof passes through the plastic area of the upper coal seam floor. Therefore, the underlying and transition areas on both sides of the remaining coal pillar are divided into Area I (15 m) → Area II (the most complicated area to control under the remaining coal pillar, 20 m) → Area III (25 m) according to the width. Furthermore, the divisional differentiated combined control technology of channel steel truss anchor cable with joint double‐way locking control function of roof and coal pillar in Area I and Area III, while channel steel truss anchor cable with joint double‐way locking control function of roof and side + high resistance integral door‐type support is proposed in Area II. Field engineering practice shows that the deformation of the roadway surrounding rock can be controlled within 210 mm after adopting the above divisional combined control technology. Finally, the mining operation can safely and efficiently pass through the remaining coal pillar. The research results have important reference values for surrounding rock control of mining roadways in the overlapping area of similar "+" type cross‐working face.This article is protected by copyright. All rights reserved.

Control Mechanism of Roof Fracture in No-Pillar Roadways Automatically Formed by Roof Cutting and Pressure Releasing

Effect of Roof Cutting Technology on Broken Roof Rock Bulking and Abutment Stress Distribution: A Physical Model Test

Investigation on the key techniques and application of the new-generation automatically formed roadway without coal pillars by roof cutting

Stability Control of a Roadway Surrounding Rock during the Cutting and Pressure Relief of a Coal-Bearing Roof at a Shallow Mining Depth

Field experiment on directional roof presplitting for pressure relief of retained roadways

Differential roof cutting for roadway support in dual gob-side entry retention on a single working face − Multilevel continuous anchor-grouting control technology: A case study

Mechanism and Control Technology of Rockburst Induced by Thick Hard Roof and Residual Coal Pillar: A Case Study

Roof cutting mechanism and surrounding rock control of small pillar along-gob roadway driving in super high coal seam

Mechanisms and Applications of Pressure Relief by Roof Cutting of a Deep-Buried Roadway near Goafs

An Innovative Mechanism of Directional Rock Cracking Mechanics and Mine Pressure Control Method for Energy-Gathering Blasting

Experiment Research on the Control Method of Automatically Retained Entry by Roof Cutting Pressure Relief Within Thick Hard Main Roof Longwall Top Coal Caving Panel

Stability control measures for roof cutting and NPR supporting of mining roadways in fault areas of kilometre-deep coal mine

Research on the Technology of Small Coal Pillars of Gob-Side Entry Retained in Deep Mines Based on the Roof Cutting for Pressure Unloading in the Lower Key Stratum

Failure mechanism and divisional differentiated control of surrounding rock in mining roadway under remaining coal pillar in close‐distance coal seam

Research on the Stability Mechanism of the Surrounding Rock of Gob-Side Entry Retaining by Roof Cutting in Dianping Coal Mine

Geomechanical Model Test Investigation of Roof Cutting and Roadway Maintenance Technology Under Fault Structures

The entry retained along gob side with small coal pillar and its surrounding rock control: a case study

Geomechanical Model Experiment Research on the Automatically Formed Roadway Without Pillars in a Kilometer-Deep Coal Mine

Characteristic and Mechanism of Roof Fracture Ahead of the Face in an LTCC Panel When Passing an Abandoned Roadway: A Case Study from the Shenghua Coal Mine, China

Failure mechanism of directional roof cutting and design method optimization

Failure characteristics and stability control technology of dynamic pressure roadway affected by the mining activity: A case study