Abstract:The production of micro- and nanosized dry powder formulations of pharmaceutical drugs by spraying methods with high yields and desired rheological characteristics is typically challenging from laboratory up to commercial scales. In this work, supercritical CO 2 was used in a supercritical enhanced atomization (SEA) process as a bottom-up method to create micro- and nanoparticles, with an enhanced control over their physicochemical properties, to produce injectable aqueous suspensions of itraconazole (ITZ). The existing drying chamber design was optimized to significantly improve the SEA process product yield. Additionally, a novel set-up was integrated for the continuous production of ITZ particles directly collected in an aqueous stabilizer media by the supercritical enhanced atomization-induced particle entrapment into suspension (SEA-PES) process. To evaluate the influence of various SEA-PES processing parameters on the particle size, morphology, residual solvent, and particle collection yield of each experimental run utilising the in-house built continuous set-up, a solvent screening study followed by a design of experiments (DoE) was carried out. Based on the given output parameters, tetrahydrofuran (THF) was selected as the optimum solvent for ITZ. The best excipient/s for stabilising ITZ micro- and nanoparticles in suspension, respectively, have previously been discovered to be vitamin E TPGS (0.5% w/w) in combination with PVP K30 (0.5% w/w). Using both the SEA and SEA-PES methods, homogeneous ITZ micro- and nanosuspensions (solid content of 200 mg/g) with D50 0.23 ± 0.06 μm and 3.5 ± 0.2 μm were produced, respectively. These suspensions were stable and resuspendable after 365 days of storage at 25 °C. Finally, utilising a newly developed discriminatory dissolution method, the in vitro release characteristics of ITZ micro- and nanosuspensions were evaluated. There was no significant difference between the SEA and SEA-PES methods to generate the drug micro- and nanosuspensions, according to both solid-state and in vitro release profiles analysis. This work provides proof of concept for establishing a cost-effective experimental platform for the continuous production of injectable micro-and nanosuspensions of ITZ.

Continuous Preparation of Itraconazole Nanoparticles Using Droplet-Based Microreactor

Synthesis of Colloidal Metal Nanocrystals in Droplet Reactors: the Pros and Cons of Interfacial Adsorption.

Preparation of Itraconazole Nanoparticles by Anti-Solvent Precipitation Method Using a Cascaded Microfluidic Device and an Ultrasonic Spray Drier

Continuous and Scalable Production of Well-Controlled Noble-Metal Nanocrystals in Milliliter-Sized Droplet Reactors.

Preparation of Smectic Itraconazole Nanoparticles with Tunable Periodic Order Using Microfluidics-Based Anti-Solvent Precipitation

Converting nanosuspension into inhalable and redispersible nanoparticles by combined in-situ thermal gelation and spray drying

The Increased Dissolution and Oral Absorption of Itraconazole by Nanocrystals with an Endogenous Small-Molecule Surfactant as a Stabilizer

Integrating micromixer precipitation and electrospray drying toward continuous production of drug nanoparticles

Continuous Embedded Droplet Printing in Yield‐Stress Fluids for Pharmaceutical Drug Particle Synthesis

Continuous Production of Water‐Soluble Nanocrystals Through Anti‐Solvent Precipitation in a Fluidic Device

Microflow Nanoprecipitation of Positively Charged Gastroresistant Polymer Nanoparticles of Eudragit® RS100: A Study of Fluid Dynamics and Chemical Parameters

Continuous Microfluidic Antisolvent Crystallization as a Bottom-Up Solution for the Development of Long-Acting Injectable Formulations

Supercritical enhanced atomization induced particle entrapment for continuous production of injectable micro and nano-suspensions

Bottom-up production of injectable itraconazole suspensions using membrane technology

Establishment of a semi-continuous nano-production line using the Microfluidizer® technology for the fabrication of lipid-based nanoparticles part 1: Screening of critical parameters and design of experiment optimization studies

Development of Stable and Intensified Mixing Processes for the Precise and Scalable Production of Uniform Drug Delivery Nanocarriers

Continuous Production of Monodisperse Silver Nanoparticles Suitable for Catalysis in a Droplet-Based Microreactor System

Comparison of different methods for preparation of a stable riccardin D formulation via nano-technology.

Droplet‐based microreactor for the production of micro/nano‐materials

Droplet Reactor System That Can Be Automated for the Continuous and Scalable Production of Noble-metal Nanocrystals.

Easy-to-perform and cost-effective fabrication of continuous-flow reactors and their application for nanomaterials synthesis