Expert system based adaptive dynamic matrix control for ball mill grinding circuit

ChenXi-song,LiShi-hua,ZhaiJun-yong,LiQi

IF: 8.5

2009-01-01

Expert Systems with Applications

Abstract:Ball mill grinding circuit is a multiple-input multiple-output (MIMO) system characterized with couplings and nonlinearities. Stable control of grinding circuit is usually interrupted by great dist...

What problem does this paper attempt to address?

Research on Multivariable Constrained Fast Dynamic Matrix Control Algorithm

LIU Fu-chun,ZHAO Jun,QIAN Ji-xin

DOI: https://doi.org/10.3785/j.issn.1008-973x.2005.05.015

2005-01-01

Abstract:For fast dynamic processes and non-square multivariable systems, a multivariable constrained fast dynamic matrix control (DMC) algorithm was presented. A two-layer architecture including dynamic and economic optimization induced an auto control structure transformation for non-square multivariable systems. The extra degrees of freedom could be utilized to calculate the optimal values of inputs when the basic control objects of outputs were met. The approach of coordinating the step response model with the parametric model was employed to improve output prediction and remove truncation error. The one-step control move was calculated by only optimizing one point in the future horizon for each output. Compared to the traditional DMC algorithm, the proposed algorithm greatly reduces the calculation burden and has better control performance, and it can be embedded in distributed control system (DCS). The effectiveness of the algorithm was validated by an industrial project and a simulated example.
The sliding variable structure control of mixed magnetic bearing system

Hua Li,XiaoLong Chen

DOI: https://doi.org/10.1109/ICICTA.2010.672

2010-01-01

Abstract:Mixed magnetic bearing system (MMBS) has a complex non-linear. Firstly, this paper analyzes MMBS according to the principle and a mathematical model is established. And then a sliding mode variable structure control (SMVSC) method is presented, which bases on non-linear system. Compared with the traditional PID control method, SMVSC has good stability and robustness. At the same time, it can rapidly achieve system balance within a short time and has a strong inhibitory effect to interfering signals. Simulation results show the effectiveness and practicability of the algorithm. © 2010 IEEE.
Application And Prospect Of The Pmlsm Driver On Grinding Machine

Yuetong Xu,Zichen Chen

DOI: https://doi.org/10.1109/WCICA.2006.1713534

2006-01-01

Abstract:Permanent magnet linear synchronous motors (PMLSM) is much superior to the traditional ones driven by rotating motor with the transition elements, but its control system is much more complex. To the model uncertainty and disturbance in grinding, a robust velocity controller was designed according to the frequency characteristic of the system and the design objectives. The Bode of the sensitivity function and the direct-forward transfer function was presented to demonstrate the disturbance rejection and robustness performance of the system. Simulation and experiment results demonstrate that the designed system is robust stable. Compared to original fluid driving system, The PMLSM driver had smaller steady-state error and better performance to reject disturbance.
Self-Optimized Control Strategy for Ball Mill Pulverizing System

Qishou Liu,Jintao Huang,Gang He,Guojun Lian,Shiwen Sun

DOI: https://doi.org/10.3321/j.issn:0253-987X.2000.07.008

2000-01-01

Abstract:Ball mill control is a difficult operation in power plant because it involves three I/O factors, namely intense coupling, non-linearity and large inertia. In order to get optimum condition and the highest efficiency, based on mathematical models of the mill, a control strategy was proposed that combines ordinary control system with dynamic self-optimized control system. This makes it possible for designing a complete mill control system using PLC and simulating software.
Application of Predictive Functional Control on Ball Mill Grinding Circuit

Xuri QIN,Xiaoming JIN

DOI: https://doi.org/10.3969/j.issn.1001-7119.2009.03.018

2009-01-01

Abstract:Ball mills grinding circuits are multivariable,strongly coupled,long time delay and nonlinear process.The operating conditions often vary violently.Traditionally grinding circuits are controlled by decouped multi-loop PID controllers that minimize the effect of interaction among the control loops.The PID controllers generally become sluggish and a accurate control of the circuit is not possible.Model predictive controllers can handle such highly interacting multivariable systems effectually due to its coordinated approach.Predictive functional control(PFC)is a branch of the MPC family.The main distinguishing feature of the PFC algorithm over other MPC algorithms is the construction of the manipulated variables.So the controller’s on line-calculation work is being reduced,parameter adjustment facilitated,tracing ability improved,featured by good disturbance resistance and robustness at the same time.Simulation of PFC studies on a laboratory ball mill grinding circuit are carried out compared with decoupled multi-loop PID controllers,Predictive functional controllers and their performances are compared.The simulation result shows that the control strategy can achieve better control performance of setpoint tracking and disturbance rejection.
Control of ball mill storage pulverized coal system

Wei XU,Xiaolu FENG,Jiandong SUN,Zhengjiang ZHANG

DOI: https://doi.org/10.3969/j.issn.1002-3364.2014.07.087

2014-01-01

Abstract:Ball coal mill system is a complicated obj ect with characteristics of multi-variety coupling,nonlin-ear and time-delay.The conventional independent three sets of PID controlling systems have no auto adapt-ability and decoupling ability,so it cannot work steadily for long term and the control effect is not good.By taking the thermal power plant's ball mill pulverizing control system as the research obj ect,the ball mill pulverizing control system's control method and existing problems were investigated,from the view of pre-dictive control.Moreover,the simulation model was established,and simulation comparison between model predictive control and PID control was carried out.The results show that the model predictive control can obtain fairly good results.
Control of ball mill grinding circuit using model predictive control scheme

M. Ramasamy,S.S. Narayanan,Ch.D.P. Rao

DOI: https://doi.org/10.1016/j.jprocont.2004.06.006

IF: 3.951

2005-04-01

Journal of Process Control

Abstract:Ball mill grinding circuits are essentially multivariable systems with high interaction among process variables. Traditionally grinding circuits are controlled by detuned multi-loop PI controllers that minimize the effect of interaction among the control loops. Detuned controllers generally become sluggish and a close control of the circuit is not possible. Model Predictive Controllers (MPC) can handle such highly interacting multivariable systems efficiently due to its coordinated approach. Moreover, MPC schemes can handle input and output constraints more explicitly and operation of the circuits close to their optimum operating conditions is possible. Control studies on a laboratory ball mill grinding circuit are carried out by simulation with detuned multi-loop PI controllers, unconstrained and constrained model predictive controllers and their performances are compared.

automation & control systems,engineering, chemical
Hybrid Intelligent Modeling Approach for the Ball Mill Grinding Process

Ming Tie,Jing Bi,Yushun Fan

DOI: https://doi.org/10.1007/978-3-540-72383-7_72

2007-01-01

Abstract:Modeling for the ball mill grinding process is still an imperative but difficult problem for the optimal control of mineral processing industry. Due to the integrated complexities of grinding process (strong nonlinearity, unknown mechanisms, multivariable, time varying parameters, etc.), a hybrid intelligent dynamic model is presented in this paper, which includes a phenomenological ball mill grinding model with a neurofuzzy network to describe the selection function of different operating conditions, a populace balance based sump model, a phenomenological hydrocyclone model with some reasoning rules for its parameters correction and a radius basis function network (RBFN) for fine particle size error compensation. With the production data from a ball mill grinding circuit of an iron concentration plant, the experiments and simulation results show the proposed hybrid intelligent modeling approach effective.
Application of Fault Diagnosis Expert System in Grinding Process

Wei Qin,Wenjun Yan,Jing Xu

DOI: https://doi.org/10.1109/ical.2010.5585295

2010-01-01

Abstract:Directing at the complex structure, cockamamie production technology and great operation difficulty of vertical roller mill, this paper constructs the fault expert system to guide and optimize the grinding process. First, the expert database is established with fuzzy cluster analysis, principal component analysis (PCA) and tendency analysis. With support vector machine (SVM) regression, the multiple regression equations of main operation loops are fitted. In online, by looking up expert database and corresponding equations, the system gives out adjustment suggestions according to the variation tendency. Making use of OPC and VC++ techniques, this system has been applied in the practical field. The practical running conditions indicate that this system is effective and credible.
A Hybrid Controller of Self-Optimizing Algorithm and ANFIS for Ball Mill Pulverizing System

Hui Cao,Gangquan Si,Yanbin Zhang,Xikui Ma

DOI: https://doi.org/10.1109/icma.2007.4304089

2007-01-01

Abstract:For ball mill pulverizing system of the thermal power plant, a hybrid controller of self-optimizing algorithm and adaptive neuro-fuzzy inference system(ANFIS) is proposed. In order to keep the ball mill pulverizing system working at the optimum point all along, the self-optimizing algorithm is presented. The self-optimization algorithm can automatically find out the extreme point and adjust the control set values in time. The adaptive neuro-fuzzy inference system, which integrates the advantages of the neural network and the fuzzy control, uses the learning ability of the neural network to optimize the membership functions and fuzzy logic rules of fuzzy control. Such combined framework makes fuzzy control more systematic and less relying on expert knowledge. Simulations results verify that the controller can control the ball mill pulverizing system effectively and has higher control quality.
-Synthesis-Based Adaptive Robust Control of Linear Motor Driven Stages With High-Frequency Dynamics: A Case Study

Zheng Chen,Bin Yao,Qingfeng Wang

DOI: https://doi.org/10.1109/TMECH.2014.2369454

2015-01-01

Abstract:Existing control approaches for the precision motion control of linear motor driven systems are mostly based on rigid-body dynamics of the system. Since all drive systems are subjected to the effect of structural flexible modes of their mechanical parts, the neglected high-frequency dynamics resulting from these structural modes have become the main limiting factor when pushing for better tracking performance and higher closed-loop control bandwidth. In this paper, physical modeling and dynamic analysis that take into account the flexibility of the ball bearings between the stage and the linear guideways are presented with experimental verification. With the gained knowledge of these high-frequency dynamics, a novel μ-synthesis-based adaptive robust control strategy is subsequently developed. The proposed control algorithm uses adaptive model compensation having accurate online parameter estimation to effectively deal with various nonlinearity effects and to transform the difficult trajectory tracking control problem into a robust stabilization problem. The well-developed μ-synthesis-based linear robust control technique is then employed in the fast feedback control loop design to explicitly deal with the robust control issue associated with the high-frequency dynamics to achieve higher closed-loop bandwidth for better disturbance rejection. Comparative experiments have been performed and the results show the better tracking performance of the proposed algorithm over existing ones.
Robust nonlinear controller for PMLSM feed drives in grinding machines

Yue-tong XU,Jian-zhong FU,Zi-chen CHEN

DOI: https://doi.org/10.3785/j.issn.1008-973X.2005.11.024

2005-01-01

Abstract:A globally stable nonlinear controller was introduced into a permanent magnet linear synchronous motor (PMLSM) feed drive to eliminate the large model uncertainties and disturbances. To enhance the stability and tracking performance, the nonlinear controller fully utilizes the signals such as the position tracking error and its integral position tracking error, the velocity and its error and the second derivative of the reference input. Then a Lyapunov function was constructed to verify the stability of the nonlinear controller. Simulations and experimental results show that the tracking error and the speeding response of the nonlinear controller is much superior to those of the traditional nested PI controller; that the nonlinear controller is robust to model uncertainties and disturbances; and that the velocity fluctuation is small for different cutting depth in the grinding.
Expert System of Mill Running in a Dressing Plant from Chengde

Zhang Jie,Wang Jianmin,Yang Zhigang,Li Yanjiao

DOI: https://doi.org/10.3969/j.issn.1001-1250.2013.07.037

2013-01-01

Abstract:For large inertia,lag and nonlinear characteristics in process of mill running,an expert system based on fuzzy self-optimizing control was put forward.Fuzzy control,self-optimizing control and traditional PID control are organically combined together,and used in control design of grinding classification system of a concentrator in Chengde.By combination of PLC and industrial control computer form a DCS system.Practice shows that the expert system for the safe and stable operation,energy saving effect is obvious.It can greatly reduce the labor intensity of on-site operation,and also improve their working conditions.
Linear Active Disturbance Rejection Control for Ball Mill Coal-Pulverizing Systems

DONG Jun-yi,SUN Li,LI Dong-hai

DOI: https://doi.org/10.13374/j.issn2095-9389.2015.04.016

2015-01-01

Abstract:The ball mill coal-pulverizing ( BMCP) system is a multivariable coupled system with long time-delay, large inertia and parameter uncertainties. This paper analyzes the dynamic characteristics of the BMCP system and proposes a control strategy based on a decentralized linear active disturbance rejection controller ( LADRC) . The proposed control strategy has simple structure, strong disturbance rejection ability, and is independent of accurate mathematical models. When it is applied to the BMCP system, parameter uncertainties, disturbances and coupling in the BMCP system can be estimated and actively compensated. Based on industrial control requirements, set point tracking simulation, perturbation simulation and random Monte-Carlo experiment are carried out. In compari-son with a PID controller, the LADRC achieves better control results and has a stronger robustness.
An Intelligent Non-Collocated Control Strategy for Ball-Screw Feed Drives with Dynamic Variations

Hui Liu,Jun Zhang,Wanhua Zhao

DOI: https://doi.org/10.1016/j.eng.2017.04.007

IF: 12.834

2017-01-01

Engineering

Abstract:The ball-screw feed drive has varying high-order dynamic characteristics due to flexibilities of the slender screw spindle and joints between components, and an obvious feature of non-collocated control when a direct position measurement using a linear scale is employed. The dynamic characteristics and non-collocated situation have long been the source of difficulties in motion and vibration control, and deteriorate the achieved accuracy of the axis motion. In this study, a dynamic model using a frequency-based substructure approach is established, considering the flexibilities and their variation. The position-dependent variation of the dynamic characteristics is then fully investigated. A corresponding control strategy, which is composed of a modal characteristic modifier (MCM) and an intelligent adaptive tuning algorithm (ATA), is then developed. The MCM utilizes a combination of peak filters and notch filters, thereby shaping the plant dynamics into a virtual collocated system and avoiding control spillover. An ATA using an artificial neural network (ANN) as a smooth parameter interpolator updates the parameters of the filters in real time in order to cope with the feed drive’s dynamic variation. Numerical verification of the effectiveness and robustness of the proposed strategy is shown for a real feed drive.
Application Of Information Fusion Based On Rbf Neural Networks And Fuzzy Control To Ball Mill Pulverizing System

Gangquan Si,Hui Cao,Yanbin Zhang,Lixin Jia

DOI: https://doi.org/10.1109/WCICA.2008.4593704

2008-01-01

Abstract:Ball mill pulverizing system is a typical multi-input and multi-output (MIMO) system with the characteristics as strong coupling, nonlinearity, large delay and time-varying. The running conditions and the precise mathematic model of the system can not be obtained easily for its complex characteristics, so the conventional control strategy is not effective. An information fusion based method including multi-sensors, data preprocessing, RBF neural networks, fuzzy controller is put forward in this article. By combining multiple sensors' information, the RBF neural networks extract features and estimate the running conditions, and then the adjustments of outputs are decided by fuzzy control. By using the fusion method, the running conditions' measurements are more accurate and reliable than that using single sensor method and the control system can adapt to the time-varying characteristic of the ball mill pulverizing system. The practical application indicates that the information fusion based control system runs stably and efficiently.
Integrated Automation System of Grinding Process

Zhi-gang YANG,Jie ZHANG,Yan-jiao LI

2014-01-01

Abstract:Grinding process is with large inertia and lag , nonlinear and multivariable coupling features , traditional control methods or manual control cannot obtain more satisfactory results , caused the product percent of pass low grinding process ,large energy consumption , low production efficiency , and the ball mill is also often appear "full mill",causes the production accidents .This paper aiming at these problems that existing in the grinding process , putting forward process management ,intelligent optimization and process control of three-layer structure of integrated automation system .Through running results of a concentration in tangshan ,which show that the system can not only steady the whole grinding process ,and improve the grinding efficiency .
All-coefficient Adaptive Control of Active Magnetic Bearing System Based on Characteristic Model

Ruochen Sun,Changsheng Zhu

DOI: https://doi.org/10.1109/icems56177.2022.9983258

2022-01-01

Abstract:Due to nonlinear characteristics of electro-magnetic field, coupling of radial degree of freedom of rotor system and interference of rotor mode by specific frequency, the model of active magnetic bearing is uncertain. All-coefficient adaptive control (ACAC) strategy based on feature model can solve the problem of nonlinear, strong coupling and the stability of the system when the controlled object is excited to the unmodeled system, and the controller design is simple. In this paper, the all-coefficient adaptive control strategy based on feature model is applied to position control of active magnetic bearing flexible rotor system. In order to improve the dynamic performance of the controller, a new integrated controller combining ACAC control with active disturbance rejection controller (ADRC) is proposed to further improve the response speed of the system to disturbances such as burst load.
Intelligent modeling and compound control of pre-grinding system

刘志鹏,颜文俊

DOI: https://doi.org/10.3785/j.issn.1008-973X.2012.08.023

2012-01-01

Abstract:In order to improve the operational efficiency and energy saving in cement plants. Detailed analysis on the pre-grinding system according its features was given. An intelligent modeling and compoud control system was built to stablize and optimize the pre-grinding system in this paper. The whole system was devided into two sub-systems, one is controlled by fuzzy logic control (FLC), and the other was handled by linear matrix inequality based model predictive control (LMI-based MPC), and the model was acquired by using least square support vector machine (LS-SVM) regression. The control system was implanted with the support of OPC, DCS and C++ techniques. The control system has been deployed in the field to control the pre-grinding system. The result shows that the pre-grinding system gets a good control from the control system, and pre-grinding system is more stable than what it was before.
Implicit Generalized Predictive Control of an Active Magnetic Bearing System

Chang Wu,Changsheng Zhu

DOI: https://doi.org/10.1109/icems.2014.7013873

2014-01-01

Abstract:In this paper, a simple implicit generalized predictive self-tuning control based on Controlled Auto-Regressive Integrated Moving-Average(CARIMA) model for an active magnetic bearing system(AMB) is proposed. The dynamic behaviors of the AMB system depend on the air gaps between the stator and the rotor. In practice, no precise mathematical model can be established because the AMB system is inherently unstable and the relationship between the electromagnetic force and the current in the coils is nonlinear. The proposed control strategy is a new method of remote predictive control, which combines the advantages of various algorithms as a whole and guarantees the stability of the open loop unstable system. With the implicit generalized predictive control algorithm, the model parameters are not need to be identified, and the solving Diophantine equation on-line can be avoided. It can reduce the workload and save time. Finally, the simulation results on the AMB system with the algorithm show the tracking performance and the effectiveness of the implicit generalized predictive self-tuning control.

Expert system based adaptive dynamic matrix control for ball mill grinding circuit

Research on Multivariable Constrained Fast Dynamic Matrix Control Algorithm

The sliding variable structure control of mixed magnetic bearing system

Application And Prospect Of The Pmlsm Driver On Grinding Machine

Self-Optimized Control Strategy for Ball Mill Pulverizing System

Application of Predictive Functional Control on Ball Mill Grinding Circuit

Control of ball mill storage pulverized coal system

Control of ball mill grinding circuit using model predictive control scheme

Hybrid Intelligent Modeling Approach for the Ball Mill Grinding Process

Application of Fault Diagnosis Expert System in Grinding Process

A Hybrid Controller of Self-Optimizing Algorithm and ANFIS for Ball Mill Pulverizing System

-Synthesis-Based Adaptive Robust Control of Linear Motor Driven Stages With High-Frequency Dynamics: A Case Study

Robust nonlinear controller for PMLSM feed drives in grinding machines

Expert System of Mill Running in a Dressing Plant from Chengde

Linear Active Disturbance Rejection Control for Ball Mill Coal-Pulverizing Systems

An Intelligent Non-Collocated Control Strategy for Ball-Screw Feed Drives with Dynamic Variations

Application Of Information Fusion Based On Rbf Neural Networks And Fuzzy Control To Ball Mill Pulverizing System

Integrated Automation System of Grinding Process

All-coefficient Adaptive Control of Active Magnetic Bearing System Based on Characteristic Model

Intelligent modeling and compound control of pre-grinding system

Implicit Generalized Predictive Control of an Active Magnetic Bearing System