Abstract:Objective: The present study determined the influence of polymerization shrinkage of eight commercially available hybrid, micro-filled and nano composites (Z100 and Filtek Supreme, 3M-ESPE; Charisma and Durafill, Heraeus Kulzer; Tetric and InTen-S, Ivoclar Vivadent; Enamel plus HFO, GDF; Palfique Estelite Low Flow, Tokuyama) placed in large class 1 cavities on the bond strength to dentin. Methods: Polymerization shrinkage was recorded for 300 s at room temperature with a Stress-Strain-Analyzer (C(FACTOR)=0.3). The maximum contraction stresses after 300 s, the time until gelation (t(0.5 N)) and the coefficient of near linear fit of contraction force/time (gradient) were analysed. For the evaluation of the micro-tensile-bond-strength (micro-TBS), hourglass shape samples obtained from a total of 32 no carious extracted human third and second molars, randomly divided into 8 groups, were used. Micro tensile bond strengths were determined by computing the ratio of maximum load by the adhesion area of the hourglass shape. In order to analyze the quality of the polymerization within fillings, hardness profiles of a surface cut thought the middle of the restored tooth and along the tooth axis were made. Further, the modulus of elasticity, determined in a three-point-bending test, as well as the variation of the modulus of elasticity and of the hardness within a filling were considered. The statistical analyses were conducted by ANOVA (alpha=0.05) and post-hoc Tukey's test. Results: A significant correlation between polymerization shrinkage and micro-TBS was found (Pearson; -0.44). The correlation between modulus of elasticity in bending test and shrinkage stress (Pearson; 0.77), coefficient of near linear fit m (Pearson; 0.72), time until gelation (Pearson; -0.52) and micro-tensile-bond-strength (Pearson; -0.45) was also significant. A high polymerization tension and modulus of elasticity negatively affected the adhesion of the composite to the tooth hard substance. Further, the number of samples lost during the slice cutting and the hourglass shape preparation was found to correlate highly significantly with the shrinkage stress (Pearson; 0.97), coefficient of near linear fit m (Pearson; 0.94) and modulus of elasticity (Pearson; 0.82). All materials showed sufficient polymerization within the filling in comparison to the filling surface, the hardness at the bottom of the filling was greater than 80% of the maximum hardness value. The modulus of elasticity was not considerably reduced within the filling. Significance: High contraction stress and modulus of elasticity, fast development of contraction force and an early start of stress build-up of materials placed in restrictive cavities cause tension in the material with a possible subsequent distortion of the bond to the tooth structure. A low modulus of elasticity is not necessarily associated with high bond strength. However, it causes a more uniform stress distribution at the restorative composite-tooth interface. This is also evident in a reduced sample loss during the different stages of sample preparation.

Optical and Mechanical Factors in the Temporal Development of Tooth–composite Bond

Durability of Four Composite Resin Cements Bonded to Dentin under Simulated Pulpal Pressure

Influence of adhesive-composite application modalities on their bonding to tooth structure and resistance of the performed restorations to failure

Acoustic Properties of Interfacial Debonding and Their Relationship with Shrinkage Stress in Class-I Restorations.

Characteristics of Biofilm-Induced Degradation at Resin-Dentin Interfaces Using Multiple Combinations of Adhesives and Resins

Evaluation of micro-tensile bond strengths of composite materials in comparison to their polymerization shrinkage

Post-failure analysis of model resin-composite restorations subjected to different chemomechanical challenges

Bonding performance and interfacial characteristics of short fiber-reinforced resin composite in comparison with other composite restoratives.

Bond strength comparison of a fiber‐reinforced composite resin: Different dentin conditions and preparation techniques

Bottom/top hardness ratio and dentin bonding stability of conventional and bulk-fill resin composites

Post-curing in dental resin-based composites

Micro-tensile bond testing of resin cements to dentin and an indirect resin composite

How the Duration and Mode of Photopolymerization Affect the Mechanical Properties of a Dental Composite Resin

Assessments of polymerization shrinkage by optical coherence tomography-based digital image correlation analysis-Part II: Effects of restorative composites

Impact of Fast High-Intensity versus Conventional Light-Curing Protocol on Selected Properties of Dental Composites

Bond strength of prefabricated and CAD-CAM milled glass fiber post-and-cores luted with conventional, universal, and self-adhesive composite resin cement

Fatigue of the resin-dentin interface: a new approach for evaluating the durability of dentin bonds

The effect of thermocycling and dentine pre-treatment on the durability of the bond between composite resin and dentine.

Characterization of Contemporary Conventional, Bulk-fill, and Self-adhesive Resin Composite Materials

Dentin adhesion of bulk-fill composites and universal adhesives in class I-cavities with high C-factor

Comprehensive Evaluation of Long-Term Dentin Bond Strength, Water Sorption, Solubility, and Degree of Conversion of Self-Adhesive Resin Composites