Abstract:The high power proton beam has wide application potentials in future clean nuclear energy system, neutron physics study, RIB production and particle physics research. Cyclotrons are intrinsic in continuous-wave beam mode, which has the characteristics of high efficient power conversion rate, compact structure and relatively low construction cost. CIAE is dedicated to developing high power proton cyclotron in China for a long time. In this talk, the recent construction progress of the 100MeV cyclotron will be presented in detail. The commissioning of this cyclotron is in progress and we got the first beam on July 4, 2014. In additions, this talk also introduce the recent progress of the pre-study of a high power 800 MeV separate-sector ring cyclotron, which is proposed to provide high power proton beam for applications neutron and neutrino physics, proton radiography and nuclear data measurement. CONSTRUCTION OF CYCIAE-100 Installing and Assembling As a driving accelerator for Beijing Radioactive Ionbeam Facility (BRIF), a 100 MeV Hcompact cyclotron, normally referred to as CYCIAE-100, is being constructed to provide the proton beam of 70-100 MeV with beam current of 200-500 μA [1]. By the end of 2013, the main magnet, the main coil, the rf system, the vacuum system, the inject system, the ion source, the diagnosis and extraction systems, the lifting system and the power supply systems are installed on site. Figure 1 shows the photo of the assembled cyclotron. Figure 1: Photo of the assembled 100MeV compact cyclotron. The total weight of the main magnet is 436 tons and the overall accuracy is 0.05 mm. The quality factor of the two rf resonators reach 9500, which is highest value among the existing compact cyclotrons in the world. In order to reduce the beam loss caused by residual gas stripping, the high-speed cryo-panel system is utilized used so as to further increase the vacuum to 5x10-8 torr level. Figure 2: The integral phase slip of the final field map. By the end of July 2013, we finished the field mapping and shimming. In order to correct the magnetic field error caused by air pressure during operation, the field map was accurately measured under vacuum condition for the first time. The trim-coils system, which is usually used in this type of cyclotrons as a supplementary method to adjust local magnetic field, is proved unnecessary in the CYCIAE-100 cyclotron since a small integral phase slip of less than ±10° (see Fig. 2) can be reached simply by properly trimming the 16 shimming-bars. The operating RF frequency for the final field map is 44.8125 MHz. Furthermore, profiting from the deep-valley structure of the magnet, the vertical betatron frequency is kept above 0.5 and the crossing of dangerous Walkenshaw resonance line at high energy region is avoided, as is shown Fig. 3. Since November 2013, we started the rf resonator conditioning, which is a time-consuming work. The main purpose is to eliminate the multipacting effects at low rf power region and to reduce the rf sparking at high rf power region. The multipacting effects can cause the mismatching of impedance and reflect the rf power back to the amplifier. In order to speed up the conditioning process, some aquadag solution is printed to the sensitive surfaces of the resonators to repress secondary electron emission. Finally, the 33 kW rf power can be fed into both resonator within one hour, which is good enough to carry out beam commissioning. Figure 3: The betatron tune of the final field map. ____________________________________________ *Work supported by NSFC (Grant No. 11375273) #yangjianjun2000@tsinghua.org.cn WEPMH1 Proceedings of SAP2014, Lanzhou, China ISBN 978-3-95450-171-7 16 C op yr ig ht © 20 14 C C -B Y3. 0 an d by th e re sp ec tiv e au th or s

52 Kw CW Proton Beam Production by CYCIAE-100 and General Design of High Average Power Circular Accelerator

Construction Progress of Two Superconducting Cyclotrons for Proton Therapy and Proton Irradiation at CIAE *

Innovative research and development activities on high energy and high current isochronous proton accelerator

High Intensity Proton Beam Transportation Through Fringe Field of 70 MeV Compact Cyclotron to Beam Line Targets

New development of the high power proton cyclotrons at ciae

Conceptual Design of an 800 Mev High Power Proton Driver

Physics Design of CYCAIE-100

mA beam acceleration efforts on 100 MeV H− cyclotron at CIAE ☆

Physics design of a 70MeV high intensity cyclotron, CYCIAE-70

Isotope production by the high current proton beam of CYCIAE-100

Independent Research and Development and Innovative Applications of High-Intensity Proton Cyclotrons Toward Serialization

DESIGN AND CONSTRUCTION PROGRESS OF CYCIAE-100, A 100 MEV H- CYCLOTRON AT CIAE

Investigation and quantitative simulation of beam physics for 230 MeV SC cyclotron under construction at CIAE

GENERAL ENGINEERING CONSIDERATION FOR THE 100MEV CYCLOTRON

The design and construction of a pulsed beam generation system based on high intensity cyclotron

Beam Line Design for a 100 MeV High Intensity Proton Cyclotron at CIAE

Design, construction and commissioning of the 100KW RF amplifier for cyciae-100

Overall Design of CYCIAE-14, a 14mev PET Cyclotron

100 MeV H- CYCLOTRON AS AN RIB DRIVING ACCELERATOR

100mev High Intensity Proton Cyclotron As A Driving Accelerator For The Radioactive Ion Beam Facility

Hˉ Cusp Source Development for 100 MeV Compact Cyclotron at CIAE