Abstract:This study achieves combustion applications of methanol-diesel dual-direct injection in a retrofitted diesel engine by investigating methanol sprays and engine performance/emissions. Methanol draws high attention due to its green production potential and ease of adaptation to existing combustors and supply infrastructure. One of the most promising methods for utilising methanol in diesel engines is the dual direct injection, which provides a wide operating range and flexible injection control. This study provides an effective solution for dual direct injection by implementing a nozzle cap idea, which can mount a conventional direct injector for methanol delivery in an existing diesel engine. The custom-made nozzle cap can provide hole orientation variations, which effectively controls the methanol-air mixture distributions within the piston bowl. To this end, methanol sprays formed through the three-hole nozzle cap are analysed for varied injector pressure of 15 ∼ 35 MPa. High-speed schlieren imaging confirmed working of the new nozzle for methanol injection with expected results of increased liquid penetration length and cone angle for higher injection pressure. The spray images also helped understand how the mixtures would be distributed within the piston bowl due to direct injection. Experiments performed on a 1-litre single-cylinder common-rail diesel engine operating at 1400 rpm, up to 70 % methanol energy fraction and a broad range of methanol injection timings of BDC to TDC, showed that the methanol-diesel dual direct injection combustion produces overall lower power output than the diesel baseline due to lower calorific value and flame temperature of methanol but significantly reduced CO 2 emissions by up to 16 % and very low smoke emissions. The results showed high sensitivity to methanol injection timings and energy fraction in terms of the measured pressure, derived heat release rate and produced power due to an increase in mixture homogeneity for earlier injection timings and stratified charge conditions for later injection timings. However, the nozzle orientation change and expected methanol-air mixture distributions showed no measurable impact on pressure and heat release rate as well as engine power output and combustion stability. The most significant impact of the methanol three-hole nozzle orientation and resulting mixture distributions was found from uHC and NO x emissions because a nozzle orientation directing methanol more towards the corner of the piston bowl opposite side of the injector led to increased liquid wall wetting and methanol in crevice volumes and thereby causing less complete combustion for higher uHC and lower NO x . The low sensitivity of methanol mixture distributions to the in-cylinder pressure and engine power output but the measurable impact found on uHC and NO x emissions empathies the required optimisation of methanol direct injector nozzle depending on the combustion chamber design of the base diesel engine.

Investigation of Injection Strategy for a Diesel Engine with Directly Injected Methanol and Pilot Diesel at Medium Load

Effect of injection strategy on a diesel/methanol dual-fuel direct-injection engine

Effects of fuel injection timings and methanol split ratio in M/D/M strategy on a diesel/methanol dual-fuel direct injection engine

Engine Performance and Emissions of A Compression Ignition Engine Operating on the Diesel-Methanol Blends

Simulation on Diesel/DME Mixed Injection System

Study on injection characteristics of diesel and DME

Combustion and Emission Characteristics of a DI Diesel Engine Fueled by Diesel-Methanol Blends

Numerical Investigation on the Influence of Injection Location and Injection Strategy on a High-Pressure Direct Injection Diesel/Methanol Dual-Fuel Engine

Investigation on efficient and clean combustion pre-injection strategy of a diesel/methanol dual direct-injection marine engine under full load

Experimental investigations of the effects of pilot injection on combustion and gaseous emission characteristics of diesel/methanol dual fuel engine

An exploratory numerical study of a diesel/methanol dual-fuel injector: Effects of nozzle number, nozzle diameter and spray spacial angle on a diesel/methanol dual-fuel direct injection engine

Experimental study on effects of pilot injection strategy on combustion and emission characteristics of diesel/methanol dual-fuel engine under low load

A full-parameter computational optimization of both injection parameters and injector layouts for a methanol/diesel dual-fuel direct injection compression ignition engine

Effect of three-hole nozzle orientations on sprays and combustion in methanol-diesel dual direct injection engines

Optimization of methanol/diesel dual-fuel engines at low load condition for heavy-duty vehicles to operated at high substitution ratio by using single-hole injector for direct injection of methanol

To achieve high methanol substitution ratio and clean combustion on a diesel/methanol dual fuel engine: A comparison of diesel methanol compound combustion (DMCC) and direct dual fuel stratification (DDFS) strategies

Simulation Study on the Impact of Injection Strategies on the Performance of Methanol–Gasoline Dual-Fuel Engines

A comparative study on operating range and combustion characteristics of methanol/diesel dual direct injection engine with different methanol injection timings

The effect of diesel pilot injection strategy on combustion and emission characteristic of diesel/methanol dual fuel engine

Numerical optimization of injector hole arrangement for marine methanol/diesel direct dual fuel stratification engines

Experimental Investigation on the Effects of Direct Injection Timing on the Combustion, Performance and Emission Characteristics of Methanol/Gasoline Dual-Fuel Spark Turbocharged Ignition (DFSI) Engine with Different Injection Pressures under High Load