Abstract:Drying is a very important unit operation in many industries such as food, pharmaceuticals, chemicals and ceramics. In most cases, wet materials are dried by forced convection using hot air flow. Heat and mass transfer processes during drying have been studied by both experimental and numerical simulation methods. For the purpose of studying the mechanism of heat and mass transfer and stress-strain distribution during the hot air drying of biological porous medium, two-way coupled thermo-hydro-mechanical mathematical model has been developed to simulate the hot air convective drying process of biological porous media on basis of Fickian diffusion theory, Fourier’s law of heat conduction and thermoelasticity mechanics. The following assumptions were made in order to find a solution to the hot air drying model: the biological porous medium was homogeneous and isotropic; the deformation during drying was elastic. The transient model, composed of a system of partial differential equations, was solved by finite difference methods. The computational procedure was programmed using C language. Some physical and mechanical properties of carrot changing with dry basis moisture content and temperature were considered. The numerical results were compared with available experimental data obtained during the drying of potatoes and carrots. The relative errors between numerical results and experimental data were both less than 5%, which showed the numerical results obtained using the mathematical model were in good agreement with the experimental data. Numerical simulations of the drying curve variations and the spatio-temporal distributions of moisture, temperature and drying stresses and strains of carrot were also evaluated. The temperature and moisture content showed a gradient inside carrot slice during drying. As the drying process proceeded, the temperature inside the carrot slice initially increased to reach the wet bulb temperature of the environment and eventually leveled off. The dry basis moisture content inside the carrot slice decreased, with the fastest decreased at the heat and mass transfer interface, eventually reached the equilibrium moisture content of the potato and leveling off. Both the moisture content gradient and the temperature gradient decreased gradually in the thickness direction. The normal stress was negative in all parts of the carrot slice, and the larger the closer to the evaporation interface. The shear stress was positive in all parts of the carrot slice, and the maximum shear stress occurred in the middle of the carrot slice. As in the case of the normal stress, the values of the normal strain were negative. The change trend of normal strain with time was consistent with that of moisture content. These results indicated that the observed physical deformations were caused by the dehydration of carrot slice during drying. The influence of drying conditions, such as air temperature, air velocity and the thickness of porous media on drying process was analyzed. Analysis showed that under certain drying conditions, the higher air temperature, the greater air velocity and the thinner slice thickness, the shorter drying time. This work should help in developing an understanding of the relationship between mass and heat transfer, shrinkage, stress, strains and physical degradation.

Stress simulation and cracking prediction of corn kernels during hot-air drying

Research on drying characteristics of corn kernel based on COMSOL porous media model

Heat-transfer simulation of slice potato during drying.

Modeling Simultaneous Heat and Mass Transfer for Microwave Drying on Apple

Study on Damage Mechanism and Crack Growth of the Corn Grain

Theoretical Analysis and Multiscale Finite Element Simulation of the Dynamic Behavior of Maize Kernel Impact on Threshing Tooth

Simulation and experimental study on the effect of deformation on heat and mass transfer in potato chips during superheated steam drying

Numerical Modelling of Drying Induced Cracks in Wood Discs Using the Extended Finite Element Method

Mathematical modeling of the drying process of corn ears

Mathematical Model and Numerical Simulation of Biological Porous Medium During Hot Air Drying

NUMERICAL SIMULATION OF DRYING CRACKING USING MULTI-FIELD COUPLING DISCRETE ELEMENT METHOD

Simulation and experimental study of heat-moisture-solute transfer during drying process of porous media

Drying Characteristics and Quality of Fresh White Waxy Corn under Different Drying Methods

Flight Crew Fatigue Management in a More Flexible Regulatory Environment: An Overview of the New Zealand Aviation Industry

STATISTICAL ANALYSIS OF FATIGUE DAMAGE LIFE OF CORN KERNELS

Spatial variation of moisture content along the axial distance of corn at different superheated steam drying temperatures and various instantaneous times

Hot air–assisted radio frequency drying of corn kernels: the effect on structure and functionality properties of corn starch

The impact of drought and heat stress at flowering on maize kernel filling: Insights from the field and laboratory

Mechanical Properties of Maize Kernel Horny Endosperm, Floury Endosperm and Germ

Modelling the Effects of Post-Heading Heat Stress on Biomass Partitioning, and Grain Number and Weight of Wheat.

Effects of growth on the diffusion constant for carbon monoxide.