Abstract:Purpose Fused filament fabrication (FFF) technique using metal filled filaments in combination with debinding and sintering steps can be a cost-effective alternative for laser-based powder bed fusion processes. The mechanical behaviour of FFF-metal materials is highly dependent on the processing parameters, filament quality and adjusted post-processing steps. In addition, the microstructural material properties and geometric characteristics are inherent to the manufacturing process. The purpose of this study is to characterize the mechanical and geometric performance of three-dimensional (3-D) printed FFF 316 L metal components manufactured by a low-cost desktop 3-D printer. The debinding and sintering processes are carried out using the BASF catalytic debinding process in combination with the BASF 316LX Ultrafuse filament. Special attention is paid on the effects of build orientation and printing strategy of the FFF-based technology on the tensile and geometric performance of the 3-D printed 316 L metal specimens. Design/methodology/approach This study uses a toolset of experimental analysis techniques [metallography and scanning electron microcope (SEM)] to characterize the effect of microstructure and defects on the material properties under tensile testing. Shrinkage and the resulting porosity of the 3-D printed 316 L stainless steel sintered samples are also analysed. The deformation behaviour is investigated for three different build orientations. The tensile test curves are further correlated with the damage surface using SEM images and metallographic sections to present grain deformation during the loading progress. Mechanical properties are directly compared to other works in the field and similar additive manufacturing (AM) and Metal Injection Moulding (MIM) manufacturing alternatives from the literature. Findings It has been shown that the effect of build orientation was of particular significance on the mechanical and geometric performance of FFF-metal 3-D printed samples. In particular, Flat and On-edge samples showed an average increase in tensile performance of 21.7% for the tensile strength, 65.1% for the tensile stiffness and 118.3% for maximum elongation at fracture compared to the Upright samples. Furthermore, it has been able to manufacture near-dense 316 L austenitic stainless steel components using FFF. These properties are comparable to those obtained by other metal conventional processes such as MIM process. Originality/value 316L austenitic stainless steel components using FFF technology with a porosity lower than 2% were successfully manufactured. The presented study provides more information regarding the dependence of the mechanical, microstructural and geometric properties of FFF 316 L components on the build orientation and printing strategy.

Creating Metal Parts by Fused Deposition Modeling and Sintering

Comparison of Stainless Steel 316L Parts Made by FDM- and SLM-Based Additive Manufacturing Processes

Additive manufacturing of 316L stainless-steel structures using fused filament fabrication technology: mechanical and geometric properties

Material extrusion-based fabrication of 316L stainless steel: analysis of debinding and sintering, mechanical properties, and corrosion resistance

Sintering parameter investigation for bimetallic stainless steel 316L/inconel 718 composite printed by dual-nozzle fused deposition modeling

Prototyping and characterisation of 316L stainless steel parts and lattice structures printed via metal fused filament fabrication

Sustainable metal-infused polymer feedstock compatible with low-cost metal sinter-based 3D printing

Study on the Forming and Mechanical Properties of 17-4PH Parts Fabricated by Metal Material Extrusion Additive Manufacturing Technique

Microstructure evolution, phase formation, corrosion, and mechanical properties of stainless steel fabricated by extrusion-based sintering-assisted additive manufacturing

Experimental Study on Metal Parts under Variable 3D Printing and Sintering Orientations Using Bronze/PLA Hybrid Filament Coupled with Fused Filament Fabrication

Anisotropy in tensile properties and fracture behaviour of 316L stainless steel parts manufactured by fused deposition modelling and sintering

A Facile and Sustainable Integrated Fabrication Strategy for Multi-Performance 316l Stainless Steel

3D Printed Fibre-Reinforced Polymer Composites — Review of the Fused Deposition Modeling Process and Mechanical Performance of Products

Anisotropic sintering shrinkage behavior of stainless steel fabricated by extrusion-based metal additive manufacturing

Shrinkage and deformation compensation in metal fused filament fabrication (mf3) sintered copper components using 3d scanning and inverse deformation

Printing, Debinding and Sintering of 15-5PH Stainless Steel Components by Fused Deposition Modeling Additive Manufacturing

Study on Performance of Metal and Polymer Composites Parts Based by Additive Manufacturing

Fused filament fabrication of stainless steel structures - from binder development to sintered properties

316L FFF binder development and debinding optimization

3D printing of metal parts using a highly-filled thermoplastic filament

Indirect Induction Sintering of Metal Parts Produced through Material Extrusion Additive Manufacturing