Selective Palladium-Catalyzed Aminocarbonylation of Olefins with Aromatic Amines and Nitroarenes
Xianjie Fang,Ralf Jackstell,Matthias Beller
DOI: https://doi.org/10.1002/anie.201308455
2013-01-01
Abstract:Molecular-defined catalysts allow for the refinement of readily available feedstocks to more complex functionalized products. Prime examples for such transformations are carbonylation processes, which make use of carbon monoxide—currently the most important C1 building block. In fact, carbonylations represent industrial core reactions for converting various bulk chemicals into a diverse set of useful products for our daily life. More specifically, the transitionmetal-catalyzed addition of carbon monoxide to olefins or alkynes in the presence of a suitable nucleophile, such as water, alcohols, and amines, leads to the formation of saturated or unsaturated carboxylic acid derivatives. Nowadays, palladium is one of the most commonly employed metals in these transformations. Compared with the reaction of olefins, carbon monoxide, and alcohols (hydroesterification) or water (hydrocarboxylation), related aminocarbonylations leading to amides have received much less attention. The same is also true compared to the well-studied aminocarbonylation of alkynes, intramolecular aminocarbonylation of alkenes, and aminocarbonylation of aryl and vinyl halides. This is somewhat surprising as the aminocarbonylation of olefins provides a 100% atom-efficient route for producing carboxamides, which represent versatile building blocks and intermediates for the chemical, pharmaceutical, and agrochemical industries. In early studies of aminocarbonylations, cobalt-carbonyl complexes or nickel cyanide were used as catalysts. Ironcarbonyl complexes and ruthenium chloride also showed some catalytic activity. However, all these reactions were carried out under very severe conditions (> 200 8C; > 150 atm). Since the 1980s, more effective catalysts, such as ruthenium-carbonyl complexes and cobalt on charcoal, have been developed. Nevertheless, the substrate scope was limited and the reaction conditions were still harsh (150 8C; 70 atm). Notably, the formation of the corresponding formamide by-products was hardly suppressed. Hence, so far there exists no general and selective intermolecular aminocarbonylation of different olefins under mild conditions. Herein, we present an efficient homogeneous palladiumbased catalyst system for the aminocarbonylation of olefins with a variety of (hetero)aromatic amines or nitro compounds under relatively mild conditions. Notably, the corresponding products were obtained in high yield with good regioselectivity, and unwanted formamides were not observed. In our initial investigations we examined the effect of a series of phosphine ligands on the model reaction of 1octene (1a) with aniline (2a) and carbon monoxide. When monodentate ligands were used, no conversion or just trace amounts of the desired products were observed (Table 1, entries 1–4). Commercially available bidentate ligands (e.g. BINAP, Dppp, L2, and L4) showed low activity in the formation of the desired product (Table 1, entries 5–14). Hence, some of our own developed N-phenylpyrrole-based bisphosphine ligands with different steric properties were tested (Table 1, entries 15–17). To our delight, L10 was identified as the most promising ligand and the reaction afforded the desired product 3aa with moderate conversion, albeit with good selectivity. To improve the reaction further, we evaluated the influence of reaction parameters such as the molar ratio of 1a to 2a, acid co-catalyst, and solvent in the presence of L10 as the ligand. As shown in Table 1, the yield of 3aa was strongly affected by the molar ratio of 1a to 2a as a consequence of some isomerization of the olefin. Consequently, as the molar ratio of 1 a to 2a increased to 2:1, the yield of 3aa increased to 86% (Table 1, entry 18). Moreover, no reaction occurred in the absence of para-toluenesulfonic acid monohydrate (p-TsOH), thus indicating the importance of the acid for the generation of the catalytically active palladium hydride species (Table 1, entry 19). Interestingly, changing the THF solvent to toluene resulted in full conversion of 2a and gave nearly quantitative yields of the corresponding amides, as determined by GC (Table 1, entry 20). No conversion was observed and the starting materials were recovered in the absence of [Pd(acac)2] (acac = acetylacetonate) or when using other catalysts such as [Rh(CO)2(acac)], [Co2(CO)8], [Ir(cod)(acac)] (cod = 1,5cyclooctadiene), [Ru3(CO)12], [Fe3(CO)12], and [Ni(acac)2] (Table 1, entry 21). With the optimized reaction conditions established (Table 1, entry 20), we examined the scope and limitations of this aminocarbonylation process with respect to various olefins (Table 2). Both shortand long-chain terminal olefins 1a–1e provided the corresponding amides in good to excellent yields and with good regioselectivities (Table 2, entries 1–4). The more challenging internal olefin 1e was transformed to C9-amides in 53 % yield. The linear amide is still formed preferentially because of isomerization of the olefin (66:34 n/i selectivity; Table 2, entry 5). Lower linear [*] X. Fang, Dr. R. Jackstell, Prof. Dr. M. Beller Leibniz-Institut f r Katalyse e. V. an der Universit t Rostock Albert-Einstein-Strasse 29a, 18059 Rostock (Germany) E-mail: matthias.beller@catalysis.de Homepage: http://www.catalysis.de