Abstract:The current research about the flow ripple of axial piston pump mainly focuses on the effect of the structure of parts on the flow ripple. Therein, the structure of parts are usually designed and optimized at rated working conditions. However, the pump usually has to work in large-scale and time-variant working conditions. Therefore, the flow ripple characteristics of pump and analysis for its test accuracy with respect to variant steady-state conditions and transient conditions in a wide range of operating parameters are focused in this paper. First, a simulation model has been constructed, which takes the kinematics of oil film within friction pairs into account for higher accuracy. Afterwards, a test bed which adopts Secondary Source Method is built to verify the model. The simulation and tests results show that the angular position of the piston, corresponding to the position where the peak flow ripple is produced, varies with the different pressure. The pulsating amplitude and pulsation rate of flow ripple increase with the rise of pressure and the variation rate of pressure. For the pump working at a constant speed, the flow pulsation rate decreases dramatically with the increasing speed when the speed is less than 27.78% of the maximum speed, subsequently presents a small decrease tendency with the speed further increasing. With the rise of the variation rate of speed, the pulsating amplitude and pulsation rate of flow ripple increase. As the swash plate angle augments, the pulsating amplitude of flow ripple increases, nevertheless the flow pulsation rate decreases. In contrast with the effect of the variation of pressure, the test accuracy of flow ripple is more sensitive to the variation of speed. It makes the test accuracy above 96.20% available for the pulsating amplitude of pressure deviating within a range of ±6% from the mean pressure. However, with a variation of speed deviating within a range of ±2% from the mean speed, the attainable test accuracy of flow ripple is above 93.07%. The model constructed in this research proposes a method to determine the flow ripple characteristics of pump and its attainable test accuracy under the large-scale and time-variant working conditions. Meanwhile, a discussion about the variation of flow ripple and its obtainable test accuracy with the conditions of the pump working in wide operating ranges is given as well.

Effects of the Varying Lateral Clearances on the Pressure Ripple of Internal Gear Pumps in Biped Robots

Experimental Research on Performance of Water Hydraulic Internal Gear Pump

Theoretical Analysis for the Flow Ripple of a Tandem Crescent Pump with Index Angles

An advanced pressure pulsation model for external gear pump

Investigations of the Micro Surface Shape for the Gear-Shaft/journal-bearing Interface in Water Hydraulic Internal Gear Pumps

Numerical and experimental studies on flow performances and hydraulic radial forces of an internal gear pump with a high pressure

Modeling of Pneumatic Dual Reciprocating Bellows Pump with Flexible Linkage

Effects of Non-Uniform Pistons Distribution on Axial Piston Pump Flow Ripple

Effects of Index Angle on Flow Ripple of a Tandem Axial Piston Pump

Flow Ripple Reduction of an Axial Piston Pump by a Combination of Cross-Angle and Pressure Relief Grooves: Analysis and Optimization

Analysis and Optimization on U-shaped Damping Groove for Flow Ripple Reduction of Fixed Displacement Axial-Piston Pump

Numerical analysis of the lubricating gap between the gear shaft and the journal bearing in water hydraulic internal gear pumps

58812 ANALYSIS OF THE PISTON/CYLINDER PAIR OF AXIAL PISTON PUMP BASED ON VIRTUAL PROTOTYPE(Fluid-Structure Interaction in MBS)

Theoretical and Simulation Investigations on Flow Ripple Reduction of Axial Piston Pumps Using Nonuniform Distribution of Pistons

Motion Modelling of the Floating Bushing in an External Gear Pump Using Dimensional Analysis

Flow Ripple Reduction of Axial-Piston Pump by Structure Optimizing of Outlet Triangular Damping Groove

Impact of Typical Steady-State Conditions and Transient Conditions on Flow Ripple and Its Test Accuracy for Axial Piston Pump

Performance reliability evaluation of high‐pressure internal gear pump

A Numerical and Experimental Investigation of Parametric Effect on Flow Ripple

Effects of Splined Shaft Bending Rigidity on Cylinder Tilt Behaviour for High-Speed Electro-Hydrostatic Actuator Pumps