Abstract:Introduction: The reduction of drag is a crucial concern within the shipping industry as it directly influences energy consumption. This study addresses this issue by proposing a novel approach inspired by the unique ridge structure found on killer whale skin. The objective is to develop a non-smooth surface drag reduction method that can effectively decrease drag and improve energy efficiency for ships. Methods: The study introduces a technique involving the creation of transverse bionic groove surfaces modeled after the killer whale skin's ridge structure. These grooves are aligned perpendicular to the flow direction and are intended to modify the behavior of turbulent boundary layer flows that form around the ship's hull. Numerical simulations are employed using the Shear Stress Transport k-ω model to analyze the effects of the proposed groove surface across a wide range of flow conditions. The research investigates the impact of various parameters, such as the width-to-depth ratio (λ/A), groove depth, and inlet velocity, on the drag reduction performance of the bionic groove surface. Results: The study reveals several key findings. Optimal shape parameters for the bionic groove surface are determined, enabling the most effective drag reduction. The numerical simulations demonstrate that the proposed groove surface yields notable drag reduction benefits within the velocity range of 2∼12 m/s. Specifically, the friction drag reduction ratio is measured at 26.91%, and the total drag reduction ratio at 9.63%. These reductions signify a substantial decrease in the forces opposing the ship's movement through water, leading to enhanced energy efficiency. Discussion: Comparative analysis is conducted between the performance of the bionic groove surface and that of a smooth surface. This investigation involves the examination of velocity gradient, streamwise mean velocity, and turbulent intensity. The results indicate that the bionic groove structure effectively mitigates viscous stress and Reynolds stress, which in turn reduces friction drag. This reduction in drag is attributed to the alteration in flow behavior induced by the non-smooth surface. Conclusion: The study proposes a novel approach for drag reduction in the shipping industry by emulating the ridge structure of killer whale skin. The transverse bionic groove surface, aligned perpendicular to flow direction, demonstrates promising drag reduction outcomes across diverse flow conditions. Through systematic numerical simulations and analysis of key parameters, the research provides insights into the drag reduction mechanism and identifies optimal design parameters for the groove surface. The potential for significant energy savings and improved fuel efficiency in maritime transportation underscores the practical significance of this research.

Turbulent Drag Reduction Characteristics of Bionic Nonsmooth Surfaces with Jets

Experimental and numerical investigation on drag reduction of non-smooth bionic jet surface

Drag Reduction Via Turbulent Boundary Layer Flow Control

Use of Bionic Inspired Surfaces for Aerodynamic Drag Reduction on Motor Vehicle Body Panels

Overview of the Technology of Bionic Surface Drag Reduction

Drag reduction using bionic groove surface for underwater vehicles

Skin Friction Reduction Characteristics of Nonsmooth Surfaces Inspired by the Shapes of Barchan Dunes

The Numerical Research of Drag Reduction over Bionic Fluctuation-Adaptive Non-Smooth Surface

Experiment about drag reduction of bionic non-smooth surface in low speed wind tunnel

Research on Drag Reduction Mechanism and Optimization Design of Bionic Jet Flow

Numerical Investigation of Microbubble Drag Reduction on an Axisymmetric Body Based on Eulerian Multiphase Model

Analysis of Aerodynamic Drag Reduction on Automobile by Using Bionic Non-smooth Surface

Active Control of a Turbulent Boundary Layer Based on Local Surface Perturbation

Mechanism of Flow Drag Reduction on Non-Smooth Surface

Rational Analysis of Drag Reduction Variation Induced by Surface Microstructures Inspired by the Middle Section of Barchan Dunes at High Flow Velocity

Experimental study of turbulent drag reduction characteristics of biomimetic divergent spines surfaces based on particle image velocimetry and proper orthogonal decomposition

Aerodynamic drag reduction analysis of vehicle body with bionic non-smooth surfaces

Improved Stable Drag Reduction of Controllable Laser-Patterned Superwetting Surfaces Containing Bioinspired Micro/Nanostructured Arrays

Research on the Drag Reduction Performance of Bionic Micro-gradient Surfaces

Numerical simulation study on the drag reduction characteristics of grooves-microbubbles coupling surfaces

Design and analysis of micro-nano scale nested-grooved surface structure for drag reduction based on ‘Vortex-Driven Design’