Abstract:The Mg-Al-RE series heat-resistant magnesium alloys are applied in automotive engine and transmission system components due to their high-temperature performance. However, after serving at a high temperature for a long time, the Al11RE3 phase coarsened and even decomposed, while the Mg17Al12 phase grew and dissolved, which limits the service temperature of Mg-Al-RE series heat-resistant magnesium alloys to a maximum of 175 °C. In this study, a new preparation method for in situ AlN particles was presented. The AlN/Mg-4Al-4La-0.3Mn composites were prepared by a master alloy and casting method. The effects of various contents of AlN (0.5-3.0 wt.%) on the microstructure and mechanical properties of the Mg-4Al-4La-0.3Mn (AE44) alloy at room (25 °C) and high temperatures (150-250 °C) were investigated. Microstructure analysis revealed that the inclusion of AlN led to a reduction in both the grain size and second phase size in the AE44 alloy, while also improving the distribution of the second phase. The average grain size, Al11La3 phase, Al2La phase, and Al3La phase of the 2.0 wt.% AlN/AE44 composite were 135.7, 9.6, 1.9, and 12.6 μm, respectively, which were significantly lower than those of the AE44 matrix alloy (179.8, 12.6, 3.3, 17.8 μm). The refinement was attributed to the ability of AlN particles to serve as heterogeneous nucleation cores for α-Mg and, at the same time, impede the growth of the solid-liquid interface, eventually leading to grain refinement. With the increase in the AlN content, the mechanical properties of composites initially exhibited an increase at both room and high temperatures, followed by a subsequent decrease. When the AlN content was 2.0 wt.%, the composite exhibited optimal strength and plasticity matching. At room temperature, the TYS, UTS, and EL values of the 2.0 wt.% Mg-4Al-4La-0.3Mn composite were 96 MPa, 175 MPa, and 7.0%, respectively, which were increased by 26 MPa, 27 MPa, and 0.7% when compared with the base alloy. The TYS of the 2.0 wt.% Mg-4Al-4La-0.3Mn composite at 150 °C, 200 °C, and 250 °C were 17 MPa, 14 MPa, and 22 MPa higher than those of the matrix alloy, respectively. The main strengthening mechanisms were second phase strengthening, load transfer strengthening, and thermal mismatch strengthening. At elevated temperatures, AlN particles effectively pinned the grain boundaries, inhibiting their migration, and hindered dislocation climbing, resulting in excellent mechanical properties of the composites at high temperatures. This study contributes to the advancement of in situ AlN particle preparation methods and the exploration of effects of AlN on the properties and microstructure of Mg-Al-RE alloys at high temperatures (150-250 °C).

High-Temperature Mechanical Properties of Aluminum Alloy Matrix Composites Reinforced with Zr and Ni Trialumnides Synthesized by In Situ Reaction

Microstructure and Mechanical Properties of Mg-Al-La-Mn Composites Reinforced by AlN Particles

Study of the high-temperature mechanical properties of Al-6061/NiTi reinforced metal matrix composites

Design, microstructure and high temperature properties of in-situ Al3Ti and nano-Al2O3 reinforced 2024Al matrix composites from Al-TiO2 system

The Mechanical Properties of Intermetallic Ni50−xTi50Alx Alloys (X=6,7,8,9)

Microstructures and mechanical properties of aluminum matrix composites fabricated from Al-x wt.% Zr(CO3)2 (x = 5, 10, 15, 20, 25) systems

Direct Laser Fabricated in Situ TiC Particulate Reinforced Ni30Al20Fe Intermetallic Matrix Composite

Reaction Synthesis of Ni/Ni3Al Multilayer Composites Using Ni and Al Foils: High-temperature Tensile Properties and Deformation Behaviour

Enhanced High Temperature Mechanical Properties and Heat Resistance of an Al–Cu–Mg–Fe–Ni Matrix Composite Reinforced with In-Situ TiB 2 Particles

Influence of Zr Microalloying on the Microstructure and Room-/High-Temperature Mechanical Properties of an Al–Cu–Mn–Fe Alloy

Microstructure evolution and tensile behavior of MgAlB4w/Al composites at high temperatures

Microstructure and tensile properties of in situ synthesized (TiC + TiB + Nd2O3)/Ti-alloy composites at elevated temperature

Improvement of the tensile strength of Al18B4O33w/Al composite at elevated temperatures by change of interfacial state

A Novel Al–Cu Composite with Ultra‐High Strength at 350 °C via Dual‐Phase Particle Reinforced Submicron‐Structure

Design of a Thermally Stable Heat-Resistant (Al2O3+Al3Ti)/Al Composite with Excellent High-Temperature Mechanical Properties: Multimechanism Synergistic Strengthening Strategy

Insight into Microstructure Evolution of In-Situ ZrB2np/AA6111 Composites with Both Excellent Room and High Temperature Properties

Microstructure-property relationship in Zr-alloyed Ni-rich NiTi alloys: Enhancements in high-temperature stability and superelasticity

The Evolution of Microstructure and Mechanical Properties at Elevated Temperature of Cast Al–Li–Cu–Mg Alloys with Ni Addition

Enhanced high temperature mechanical properties and heat resistance of an Al–Cu–Mg–Fe–Ni matrix composite reinforced with in-situ TiB2 particles

Fabrication, Mechanical and Thermal Behaviors of Antiperovskite Manganese Nitride Mn3.1Zn0.5Sn0.4N Reinforced Aluminum Matrix Composites

Microstructure and Mechanical Properties of Ti2AlC Particle and In-Situ TiAl3 Reinforced Pure Al Composites