Abstract:The nickel(Ni)-patterned electrode enables researchers to quantify the triple-phase boundary (TPB) length and Ni surface area, exclude the influence of bulk gas diffusion and clearly separate the active regions of the chemical/electrochemical reactions. This tool has been studied for identifying the reaction mechanism in SOFC but rarely in SOEC. In this study, the Ni-patterned electrodes with the stripe width of 100 μm were tested in both the solid oxide fuel cell (SOFC) and solid oxide electrolysis cell (SOEC) modes at the atmosphere of H2O/H2 and further H2O/CO2/H2/CO. The experimental test shows the stability of the Ni-patterned electrode in the H2O/H2 atmosphere was much poorer than that in the CO/CO2 atmosphere due to the nickel reacting with steam. Thus, the Ni-patterned electrode needed to operate at a temperature of ≤700oC with the inlet H2/H2O molar ratio of >7 and the current-applied time shouldn’t be over 5 h to keep the accuracy of the TPB length and Ni surface area. The effects of the temperature, partial pressure of H2O and H2 are investigated. The activation energy of the Ni-patterned electrodes was 0.386 eV. The electrochemical performance had a positive correlation with both the partial pressure of H2 and H2O, especially showed higher sensitivity to the partial pressure of H2O. Further, a possible mechanism of the H2O/H2 electrochemical conversion was proposed according to the experimental data and existing literature, which contains two-step charge-transfer reaction: H(Ni)+O2-(YSZ)OH-(YSZ)+(Ni)+e- and H(Ni)+OH-(YSZ)H2O(YSZ)+(Ni)+e-. Based on the experiments, an analytical calculation was performed to investigate the rate-determining steps in the Ni-patterned electrodes by bridging the connection between the kinetic parameters and operating conditions. The results indicate the rate-limiting steps may be different for the SOFC and SOEC modes. In SOFC mode, the H2 electrochemical oxidation could depend more on the charge-transfer reaction H(Ni)+O2-(YSZ)→OH-(YSZ)+(Ni)+e-, however in SOEC mode, the rate-determining step of the H2O electrochemical reduction should be H2O(YSZ)+(Ni)+e-→OH-(YSZ)+H(Ni). In this way, a reversible mechanism could be applied for reversible SOFC (RSOFC) to describe the conversion between hydrogen and steam by different charge-transfer-reaction domination in the SOFC and SOEC mode. Figure 1

Mechanism of Rate-Limiting Step Switchover for Reversible Solid Oxide Cells in H2/H2O Atmosphere

Reaction Mechanism and Rate-Determining Step Speculation of Reversible CO/CO2 Electrochemical Conversion on the Nickel Patterned Electrodes

Reversible H2/H2O electrochemical conversion mechanisms on the patterned nickel electrodes

A Practical Approach for Identifying Various Polarization Behaviors of Redox-Stable Electrodes in Symmetrical Solid Oxide Fuel Cells

From Fundamental Interfacial Reaction Kinetics to Macroscopic Current–Voltage Characteristics: Case Study of Solid Acid Fuel Cell Limitations and Possibilities

Functionally Graded Infiltration Triggering Ultrahigh Electrolytic Current in Robust Reversible Solid Oxide Cells

Elementary Reaction Modeling of Reversible CO/CO2 Electrochemical Conversion on Patterned Nickel Electrodes

Mechanism Analysis of the Reduction Process of the NiO-YSZ Anode of a Solid Oxide Fuel Cell by Hydrogen

Mechanism and Kinetics of Ni-Y2O3-ZrO2Hydrogen Electrode for Water Electrolysis Reactions in Solid Oxide Electrolysis Cells

Hydrogen Oxidation Mechanisms on Perovskite Solid Oxide Fuel Cell Anodes

The Mechanism of H[sub 2]S Poisoning Ni/YSZ Electrode Studied by Impedance Spectroscopy

Mechanism for Reversible CO/CO2 Electrochemical Conversion on a Patterned Nickel Electrode

Carbon Monoxide/carbon Dioxide Electrochemical Conversion on Patterned Nickel Electrodes Operating in Fuel Cell and Electrolysis Cell Modes

The Reduction Process of a NiO/YSZ Anode for Intermediate Temperature Solid Oxide Fuel Cells

Importance of Oxygen Spillover for Fuel Oxidation on Ni/YSZ Anodes in Solid Oxide Fuel Cells.

Unveiling Key Interface Characteristics of Ni/Yttria-Stabilized Zirconia Solid Oxide Cell Electrodes in H2O Electroreduction Using Operando X-ray Photoelectron Spectroscopy

Elementary Reaction Modeling of Solid Oxide Electrolysis Cells: Main Zones for Heterogeneous Chemical/Electrochemical Reactions

Bifunctional Electrocatalyst Materials for Improved Cell Reversal Tolerance in PEM Fuel Cell

Coupling Ammonia Catalytic Decomposition and Electrochemical Oxidation for Solid Oxide Fuel Cells: A Model Based on Elementary Reaction Kinetics

Numerical modeling of an anode-supported SOFC button cell considering anodic surface diffusion

Reversible Solid Oxide Cell with Proton Conducting Electrolyte:Materials and Reaction Machanism